Video

What spindle speed and feed did you set for a 10-degree cutter?

Great Job, Thank you !!

One of most complicated technic in wood cnc is inlay. Thanks.

It's a pity that you don't provide parameters for the diameters of the cutters you use

I’m buying one tonight. Thanks.

C'est un superbe tutoriel, comme je n'en ai jamais trouvé (ni en anglais ni en français). Question : Je n'ai encore jamais débuté de projet d'incrustation, pensez-vous que la nouvelle version Vcarve Pro 12 prenne en compte de manière automatique ces calculs ( czcams.com/video/P1nbIjlBYG4/video.html ) durant la conception ? Merci beaucoup pour ce que vous faites et salutations 👍

Excellent work. What kind of spindle speeds and feed settings do you use on your 1/16" bits for epoxy cutting? I seem to break my 1/16" 0 Fllute bits every time. Trial and error on numerous settings and still break bits routinely. Any insight would be appreciated!

Very nice work! Not your first one I can tell.

Spectacular. What kind of hard wood are those?

Bonjour, Je ne comprends pas. La version d'essai de Vcarve n'autorise pas l'enregistrement du projet. Faut-il payer ?

I'm a new subscriber like your work very nice I'll check out some of your past videos

Wow, that's awesome!

PSA: Tapping with a hammer (17:28) is a critical step. You can see the piece shifting down. I did not do that & paid dearly. So is clamping at the entire perimeter, against the piece itself, with multiple clamps.

On your "Motorcycles" part, you effectively have a zero glue gap, correct? You drilled to the exact amount. If you can do this for part 2, why can't you do this for part 1? You wouldn't need the epoxy then. On my attempt, I left a glue gap of 0.6mm. Small enough to effectively become a glue joint

2:00 "Flattening takes 40 minutes" What are your thoughts on a flattening bit? Is it not suitable for end-grain?

Bonjour Stéphane, serait il possible de savoir quelle résine vous utilisez.Je teste plusieurs résines en ce moment et l'humidité me cause pas mal de problème 🫤. Merci pour le partage (de vos vidéos et de vos infos si vous le voulez bien 😅)... Sam

What wood is being used

Ravenclaw the best!

Upgrade potentiels : utiliser une fraise de 30 pour le surfaçage Faire un topcoat en résine au lieu de mettre du vernis, ca fera une finition parfaitement lisse, on peu voir que tu as des trou et des rayures sur le résultat final Débuller la résine évitera les imperfections lors du surfaçage aussi Sinon beau travail !

Wow. Very nice. With epoxy taking so long to dry, how long does one of these take you to complete? How long do you wait for each color to dry?

Epoxy is nice, but I like inlay films better.

Super Stephan

Trop beau ! Ca faisait longtemps que je n'étais pas venu voir une de tes vidéos !

Great job!!

Encore une belle réalisation 👍🏽

Awesome job!

nice work

NICE! Inspector approved. Lol

Me gusto como haces el proceso 3 veces ,es mas rápido que dejar una sola operación

Clair et précis. Merci beaucoup.

Such a brilliant tutorial

Superbe ❤

What values determine the glue gap vs how much the male piece protrudes above the female? In your example I assume the 1mm glue is the difference between the depth of the female piece compared to the final depth of the male. 8 vs 9. But what values control the gap of the male piece above the female? Thx

Stephan, Thanks for this video!! I just did an inlay and I couldn't figure out why my bit was plunging all the way to the final depth. As soon as I started watching this, I realized what was happening. I didn't even need to finish watching, but I enjoyed it. Thanks again!

Hands down the best instructional video I've come across, your explanations and diagrams are excellent and to the point, every question I had while watching your video was answered seconds later, easily my new go to tutorial channel, thank you for taking the time to put this video together, I've work in video production and know how much time you must have spend filming and editing this piece, it is very my appreciated. Bravo.

Very impressive!

❤❤ что за программа

Is this finish suitable for a plate that will be used for eating and washed?

Nice video. Very clear. I have been creating quite large epoxy resin inlaya and have found normal PVA glue works fine even on pine. I cut the shape/pattern, then paint with PVC let it dry then add resin. I also use a drum sander to do the rough sanding followed by orbital sanding to 400 grit.

Bonjour, est-ce qu'il est obligatoire de travailler en bois de bout pour ce genre de choses, ou bien cela n'a pas d'importance ?

stunning work

I saw that at 25:22 your bit gets mixed with glue. I have the same problem, do you know why this appens?

Thank you very much for the very informative explanation. It is greatly appreciated.

those deck planks you use... is that padauk? that stuff is pricey here in CO. who wastes so much padauk?

Magnifique

Bonjour Stephan Merci pour la vidéo qui est tres claire. Je viens de realiser ma première incrustation à l'aide de ta vidéo, ça se presente bien, j'ai collé ce soir, je surface demain, je suis confiant sur le résultat. J'ai utilisé en finition une fraise conique (14 degrés) avec en bout un R0.5, c'est pas l'idéal avec le rayon de bout, j'ai fait une incrustation d'une étoile à 5 branche pour le test. Les pointes de la partie male de l'etoile sont pointues alors que la partie femelle a le rayon de la fraise, ca force un peu pour l'incrustation (ça m'a permis de valider le principe). En attendant de me procurer la bonne fraise Cordialement Pierre

Bonjour Stephan Bravo pour toutes les vidéos que tu fais. Dis moi, c'est quoi la pate (cire) que tu appliques apres l'huile? Cordialement Pierre

Merci

what is the last coating spray?

just curious, why do you surface with only a 6mm bit?