Video

I have never seen a Fish carb, if so economical, why are they not available.? On the other hand, have always regarded the S.U. carb, as the work of a genius.!

double points is longer spark duration speed trick

Nice tool. Have you finished the timing tool for the 3 bolt (helmet cap) distributors? Going to buy both tools

Finally an American that kept the guard on his grinder!! Thank you sir. Your digits will love you for it

Good information

could someone point me in the direction of where i can get frame metal like this

Nice piece of tech on the set up of these distributors, both parts 1 & 2. You might also have mentioned that after setting the points gap, remember to re-tighten the screws on the points mounting plate, though most folks probably already assumed that step.

Where did you get the metal?

I hope you are going to bevel all the pie cuts . Need full penatration. A + work so far. When you flush grind your welds you won't have any weld left ! ! !

I've never seen you or this car build before I came across this by accident googling rear radius rods for ford model A. You earned a subscriber.

Ordered on may 16th , haven’t gotten an email confirmation or tool yet , I don’t know how to communicate with them about my order

Excellent progress. Good luck on your treatment - you're going to kick its ass again. You're an inspiration.

Thanks a lot. form Bangkok

I should have pulled the security camera video for you for bending up the bedsides.

Coming out nice , I’ve would of like to see some video of you making the bed sides on the Mag brake , some other time .

Tilly and Clash!

Thanks for the motivation..... Looking Great....

this video should definitely have more views then it has, very nice presentation and information, like the paper cutouts explaining everthing!

I got an original 8 BA carb at a garage sale and I don’t know how much it’s worth. Decent condition and could be cleaned up real well. Any ideas?

this is frustrating, how do i purchase this tool?

How does that affect your findings?

Why is a ballast resistor needed?

What is a ballast resistor?

The principle of that carb looks very similiar to the Kendig carburetors

A little more explanation would be helpful. Reminds me of those Chinese gadgets videos.

will you ship overseas to Australia?

I have one and am in need of another one for my boxer engine. They rarely appear on ebay. Does anyone have a spare they are willing to part with?

Are you going to put fish plate on your kick up and your pie cuts

Looks simple enough, have you finished up on the helmet style timing fixture. Keep up the good work .

You never explained the cons of electronic distributor and how to know and test when the electronic distributors' magnetic parts stop working. What are the signs and symptoms of a failing or bad electronic distributor?

Cnc is the best way to do it

!! Awesome to see thanks for sharin your Project with us signed up Cause it looks easy enough to do and Build Don't need to be Rocket Scientist to build your Project so Hopefully ya got more to Show us Looks like it gets cold were ya Are too good to see we get Down here to minus 45 the Other day so its winter time Spring around the Corner ther Sayin so keep your HEAD up and stay warm toooo keep them comin from Canada SK we got this going to give it a Shot !!! Brrr chilly Nice Puppy too got one and lots of Rabbits too

The photocell one of the ignition wire falls off the spark plug and has nowhere to discharge to it'll burn out your photo cell and you'll have to buy a new one my suggestion is not buying that one Mallory

The reason for the dual point ignition is to increase the "dwell" time, which allows more current to flow through the coil primary, which allows the coil to output a higher voltage spark, allowing you to increase the plug gap and increase engine power.

Great video, thanks for taking the time to make this!

That master has to be for drum / drum if that what you're running due to the residual valves in the outlets. If it's a disk / drum it will have the wrong residual valve on the front outlet. Propositioning valves are talked about a lot but most people dont even know what residual valves are.

thats not engine turning !!

How about beed rolling an 18 or 16 GA steel floor pan.

very nice ! this video has been the best i have seen on a frame build ever!!! I have looked , trust me... even the big money channels cant top this!

Awesome job my friend! 🍻 Cheers

Very nice Ry

I like the problem-solving too - this helps me get ideas for my own projects!

Looking good Ryan! Its always the little stuff that takes all the time. A little pre work and you can build everything the same! Nice!

Appreciate you bringing us in on the problem solving part. It’s great to see the challenges and then eventually the solutions. Huge fan of the jig. Always time well spent.

Looks like a fantastic tool! Would you ship to New Zealand?

Super bead roller

Very neat carb. Your video has some of the best info I've found. I'm looking to see if i can find a decently priced M1 to put on the 300 six in my vintage race car.

Got mine on order! Thanks!

Awesome info! I just got my first bead roller and this will help me with my first project on my car. Thankyou for your channel.

Cool I did a video on the gapper 7 years ago 🙂