Video

Naja... eben ein nettes Spielzeug.

But how do paint it white?

Hola prodra decirme como seria el orden para regular valvulas en esos motores 1.4?

i was curious how to weld a bearing mount. nice destructive demo guy!

I know this is some 7 yrs old video ,but changing headlamps from factory to led lamps ,your no longer be using vw lamp adjuster on the dashboard which is motorised ,so what do you do with the electronics - as new lamps surly won’t be a straight forward switch ?

you a balkan?

Does the rocker arm have a direction or indifferent?

Hiç güzel olmamış

Mine is completely stuck on locked. Tried this but didn’t work. How can I open the door to fix the door lock. (Drivers side)

🤦🏻‍♂️Bro tf you will be blind from that white light. Blue is way better and sexy.

How did you calculate the radius.This is parabolic mirror and the radus of banding the reflector is the most importing thing ,to reflect most of the signal back to the drone dipole

I can't believe people prefer blue color, white one looks like modern car, its clean and looks modern. Blue one looked like outdated 20years old dial and because its colored it might not much interior

I think blue light looks much better than the new one. But I do appreciate you for making this video and showing us how this is done!

вот они рукоблуды ,а я то думал кто ковыряется в приборках,иди...на ты бы лучше решил проблемы с подушками а не колхозанил )))))))))

I also have a mk4 and also a 2 din radio every time I drive there is no signal on the display, if I stop it works normally again. Can anyone help?

The big one .....make a heavy metal bender👍

Great, you made it look uglier

MUCHAS GRACIAS AMIGO . EXELENTE VIDEO. COMPACTO ,MUY EXPLICITO . GOOD JOB , CONGRATULATIONS.

Great job!

Рассеиватель надо было ставить

Слишком ярко

Let's be honest... You completely screwed it changing from blue to white

Can anyone tell which pin i should apply 12V to test the dash lighs when its on the table ? Would be much helpfull…

Just right for that propose.

Sweet!!

My speed indicator does not work properly after i removed it and replaced it .. what should i do ?

Eye Doctors report that little extra brightness in white lights helps prevent pupils from fully dilating, helping your eyes adjust better to those hideous LED headlights that blind everybody. Also love the fact I can read my dash during the daylight. Great job on the video so where do you get the work light for savaging white leds?

My Peugeot 306 XR 1.4l 3-door hatchback in the beautiful color Peugeot EGED has this issue, which i recently discovered after a failed MOT. Drove it to a garage where i have access to a bridge and plenty of tools and discovered coolant in the oil after taking off the valve cover. The MOT report itself cited the blinkers were too yellow, too high emission, front brakes rotted, something wrong with the rear suspension(later discovered myself the right rear shock absorber was completely stuck) and the chassis beams infront have rot, though luckily behind the front wheels where its easily accessible by just removing the wheels, or for entire access by removing the strut towers. But in a week or two I'm gonna fix the stuff on the mot report and do a block revision, already ordered all the parts for the suspension and lights, brakes, rust converter and primer + paint + rust protector for the spots to be cut out and replaced But the coolant in oil resevoir indicates head gasket failure and also likely why the emissions are too high, gonna order a complete gasket kit, new water pump, belt, pulleys etc. The car just looks too good to not save it

I read the title as "Homicide wrench", 5 or 6 times. Great video anyway!

I think the white light is better. But that it is too bright. It makes the numbers less visible and it looks like it's making it blurry. Nevertheless, your skill and hard work is appreciated. I thought it was much harder to do. Soldering can be tricky, but with a clean tip you can do a lot.

So i dont have to take the timing belt fully off?. Im confident doing gasket but not so the timing belt. See how i feel as i go. Pump will probably need changing too

My leds dont turn completely off. Rhey are glowing a bit when they should be off completely. Any fix for this.

Blue leds suck sooo bad. Warm white is the best.

You cuold GREATLY reduce the excess heat by not rushing. Take a few moments and do in small tacks, pausing briefly. Th same technique is used with very thin metals. I am looking for options of adding the ability to rotate my 43" PC TV/Monitor to my diy mount. Considering bushings as well.

Radio waves act like light so if you place a light where the antenna would be, you could adjust the bend in the reflector to get the most light out. Also keep the reflectors pointing more toward the drone instead of the sky might help. Thanks for the experiment.

sei un grande, io non avrei avuto tutta la tua pazienza per cambiare quei led, Ma volendo fare l'avvocato del diavolo, non ti sembra eccessiva tutta quella luce nel quadro? non ti da fastidio quando guidi? cmq bel video!

DIY idea

Was wondering what kind of engine it had. Seems to run on borscht.

Watching him try to desolder the LEDs with a soldering iron and not using a hot air station makes me cringe

LAŠKO PIVCE ZA MIRNE ŽIVCE

ustam laguna1 arac gostergeler calismiyor gosterge sigortasini sokup takinca calisiyor 24 saat sonra sorun ayni tesekkurler

Hi, why "chech engine light" not turning on at start for some time ? It suppose to be like that on this golf 4 ? On others golf 4 it turns on for some seconds then turn off's. Thanks.

That shyt didn't work one bit😂

Comment je peux avoir ces phares led

These where meant to charge the battery banks so the load would be minimal at the time of cranking. You would use at a steady pace about 1 crank a second for 30 minutes every few hours to recharge the batteries

White ❤ good job 👍

It's not step by step

Pozdrav, Zanima me kod spajanja kabela na multimediju…. Gdje si (tj na šta si zalemio/zaletovao crvenu žicu za kontrolu rikverca) u moru žica koja je to boja ???? Zuti konektor ide na Zuti to nema fule. I Nazad napajanje si uzeo od rikverca ok… Zuti dio si konektovao na Zuti konektor a na šta si opet na ovom kraju zaletovao/zalemio crvenu žicu koja je duga 10-15cm isto kao na prednjem dijelu kod multimedije. Pozdrav

Thanks a lot I caught up on time before I could've ruined my bearings!

I work at a tech repair shop, and i have recently started to collect all the batteries like this, i now have 9 battery packs.