Video

You saved me with this!! Thanks for the upload brother

3

You have to attach the chain to a winch or tractor. You can't pull it by hand using a tire.

You want the light off take the bulb out

I didn't see much here except raking gravel (kindof). I was looking for a rake that brings ROCKS to the surface.

Can you show me how it work , i want to make mower peoject but it hard to search it

A ufo in the house.

I bought 2 of these for 500 bucks. With the liquid cool engine great tractors

I had a D17, I loved that tractor. It had a homemade/aftermarket 3 point hitch on it. Not sure what it was, but I cleared a lot of land with a Bush Hog. The Power Director hand clutch was perfect for dropping it back into low speed or even neutral when hitting heavy brush and popping back into high for lighter grass. The 3 point setup lost the traction booster, so I didn't plow with it.

Also you can use a socket and rachet to move the tensioner to remove the belt-put the socket on the bolt on the tensioner and its perfect to leverage the tendsioner pulley but as always be careful and use correct size socket

My 88 Runs OBD1…assume the 91 does too. Short the pins on the OBD1 connector and read the “Service Engine Soon” flashes (you can Google how to read the codes). That will give you an idea of where to look. I had all sorts of readings - ended up replacing plugs wires, distributor cap and rotor, coil, EGR valve,relays, etc. Finally, I got an OBD1 flashing sequence that pointed to the computer. The computer in mine (88..2.5L) is an aluminum box located under the dash, behind the glove compartment. It’s kind of a pain to get out, but you can…one screw hold it’s blacked underneath the dash. I found a replacement computer in a junkyard (you have to have the same serial number box). There is a strip cover held on with two screws. Remove that and you can get to the EPROM inside. Transfer the EPROM from your truck to the replacement computer. Then connect and reinstall the computer. Once I did that, my truck Rand trouble free…and still does. Good luck!!

rough idle might be the MAP senson -its the black item attahed to the front of air cleaner housing Also the Idle air control valve it is under the air cleaner it attaches with 2 screws i saw a video where you can clean the Idle Air Control Valve i guess you can clean it with brake cleaner (dont fill up the part cause it is electrical the point of the valve should be clean and clean the inside of housing being very careful be real careful when installing the IAC the screws are small place something under the area to catch the screws incase you drop them a white rag or whatever check other videos gather info hope you can sort out the problem but it does sound like the MAP sensor uh i just noticed this video was 13 years ago well im late

sometimes you can remove the tensioner and lubricate it around the mounting bolt and free up the rust -pb blaster or similar rust removal type spray and always lubricate new parts if they are high wear area -I always grease mounting bolts and the threads -clean the engine threads to and blow them out with air somehow

Not enough fuel. Carb could be blocked,fuel line could be blocked or better yet water in the tank. Or possibly the carb needs adjusting.

Is that turkeys I'm hearing 😮

A new one is like $200.

I think the through bolt and spacer you replaced is part of the design, engineering for strength and balance. That gap looks like it may cause problems under stress.

Que tipo de aceite usa ❓

Great older mower! I have one bought 5 years ago and have been mowing 4 acres with it replaced the deck belt drive belt and battery . Its built well has servicable hydros and grease zerks for everthing.

Those computer boxes for the 2.5L are hard to find. I got one in a junkyard…replaced the EPROM and my 88 runs like a top.

My favorite John Deere series

what year model is it

Love it. Those old Simplicity's are bad ass. I would prefer an original engine but very cool but nonetheless an awesome machine.

Is that all???

Can a Leyland 384 lift a power link box

I had a very similar problem with my “88. It took me a while, but I found a computer box in a junk 2.5…pulled the EPROM from the original and put in the replacement. It did solve all the problems. I also picked up a spare box because they are getting harder to find.

Beautiful lilac 😊

I just found one. Runs great but I'm curious does the transmission have 2 gears or just one?

I had that same problem with the original blinker assembly. I couldnt get that clip on the outside to hold into the new grill. so i found that In between the 2 lights there is a tab, i drilled into and then into the back of the grill and used a couple zip ties to keep it tight. Kind of a cob job but it works and i didnt have to buy to buy a couple blinker assemblies. Before doing the zip tie thing i tried screwing with that springy tab by filing and using a screw but it would still pull out pretty easy. So out came the zip ties....lol

Saudades de minha infância andava com meu pai de trator pra todo lado.

How long did it hold up? I had to do this on my old 03 as well except it was on a cat

Lo usa para arar? Se consiguen los respuestos ahi

That’s gotta be a bitch to get parts for

Yes please update to see how well it works, I might need to give that a try

Bought a slightly used P3416 off Ebay about 7 years ago and it's a great little saw. Got tons of use out of it and it still runs great

How long do the batteries last on the regular m12?

Is that at full throttle? Great video!🤩

Tractor fiat de argentina!..

Oh my God this is the video that saved my life and saved the truck thank you very much you are a godsend I've been spending over months fixing this or trying to fix it figuring out what the hell is going on kept thinking it was the security but no error was it was these two ground wires or I've been spending over months fixing this or trying to fix it figuring out what the hell is going on kept thinking it was the security but nope here it was it was those two ground wires that you showed in your video I thought I cleaned the ground wires but I guess they're grounding something else out underneath on the frame let alone knowing that this is a used truck and whoever had it before had attached stuff to it thank you again❤

So I actually have the whole tractor with the steering wheel and seat . Missin the engine . I thought we had a cycle bar mower that went on it . Been sitting on farm 50 years . Bringing it home to restore it ..not finding much about the actual ride on .

Can you help me, I have the same one as you but I don't know how to turn it on, when I plugged it in several zeros appear and it doesn't allow me to use the other buttons, they never change from zero. Could you help me maybe?

LOL I didn't know they made these trucks without a tach,😮 that sucks😊

I had the same issue but with the ground cluster on the left inner fender. I put a 6 contact bus bar in and sanded all contacts with emory cloth and just a thin coat of die electric grease. Also added a separate ground wire. This is a common and frustrating problem with 1st gen Canyons and Colorados.

czcams.com/video/pccuAUNwfw8/video.htmlsi=n1_s_u9ta-2ShFXH I’ve got full arsenal of pulleys and winches but they are gonna sit lonely when I put together the four inch square steel tubing laying out back. This just made me smile. I’ve gotta try it. If a bit of a mess is not a problem, a pressure washer will expose the highest main roots. Sawzall to snip ‘em. 🤜🤛

I would have preferred the white l e d lights as opposed to the soft blue lights of these have. So I will be shopping for a different brand.

I have the craftsman with the 3 speed switch

This gun isnt ideal for lug nuts, you would want to use the 1/2 impact for bolts or nuts of that size, this gun is good for smaller nuts and bolts, i would say 17-18mm and below, it will take fresh lug nuts off but not ones that have been sitting for a while,

I am so glad to come across this video saved us money. Have 2010 GMC Canyon that was throwing fault codes and the dash cluster would go blank when driving. Took to a dealership and they said we needed a new EBCM that they don’t make anymore. Options were to live with it or get EBCM reworked. While doing research found this video. After taking the ground off and putting back on it all cleared.

Thats not cool

He's doing a fantastic job! 👍🏼👍🏽👍🏾Many people don't realize cats do thier own kind of guarding. If you pay attention to thier countenance, they will alert you to activity or someone approaching. I feel guarded if I walk with my cats at night or in woods.🐈‍⬛