Video

Let’s go!

Access to the winch control box is from the top of the grill near the hood latch. The temp sensor is just zip tied back out of the way.

@@heftyfabworks Thanks. So the location of the temp sensor is not critical? Can be anywhere?

@@BlackDotPatrickthat’s correct

We don't yet but it is on the list.

@@heftyfabworks looking forward to it!

Thankyou! Looking forward to it

If only that was the way business worked

Awesome! Please don't hesitate to give us a call if there's any questions you may have! 719-598-1776

We appreciate the kind words! If there's anything else you've been curious about when it comes to fabrication please don't hesitate to leave a comment and we can possibly make a video for it in the near future!

We don’t have a shop in Vegas. We are in Colorado Springs,CO. We can definitely recommend some good shops in your area though

Customer bought them but they are available at several online retailers like Runnin4Tacos

@@heftyfabworks Thanks so much for the heads up.

The Xterra skids will fit the R51 Pathfinder with the exception of the gas tank skid plate due to the rear subframe and independent rear suspension

Glad you like them!

Not for the 1st Gen Xterra

We do have front license plate brackets available for them but not all states require a front license plate. Building a winch bumper without cutting the front cover isn't really feasible. If you are looking for a front cover or guard there are some available on the market but that is not the intent of this product. This bumper does work with the factory and most aftermarket skid plates without any interference.

Thank you. It was a well thought out build with just the right touches.

It does have the Sasquatch Package with the 2.7. You can definitely feel the 37’s.

Thank you. This was a quick run down for the first orders going out. We will be doing a full video soon

Thank you! A lot went into this one

Thanks

This one we used a heavy load rear leaf spring setup which gives it a higher ride height in the back. The customer frequently pulls a trailer and needs the extra load capacity.

Luckily he was wearing a welding hood. 😂 very few nerve endings left in the fingers

Yes we do, just give us a call

The Toyota alignment cams are notoriously weak. They tend to bend over and make alignments impossible without repairing them. This is one of the solutions to strengthen the weak points on the lower control arm mounts. It strengthens and reinforces the mounts as well as eliminates the weak point in the Cam Bolt alignment tabs. This is the most aggressive kit on the market for this application, there are other less involved cam tab replacement kits as well that we install and stock.

We are looking into it!

That's correct. All of our full front bumpers do fit the 10-13 models as well as the limited models. The only thing you will have to do is relocate your blinkers.

For the 4 Runners

Hefty Fabworks

We have several options available and in stock. Just give us a call at 719-598-1776

2 beers then cut. Be careful though, 3 and your cut lines might get wobbly

Right on!!! Enjoy! Let us know if you have any questions!

Definitely a good idea. I’ve cut probably in the neighborhood of 300-400 of these at this point. I can almost do them blindfolded.

Same fior the limited models

57 to 63 lbs depending on options

You absolutely could use a laser but not everyone wants to buy a laser to cut their bumper cover.

Hello! We can put together complete packages for you. Just give us a call or shoot us an email! 719-598-1776 heftyfabsales@gmail.com

Thank you! We take a lot of pride in our work

Thank you! We'll be here!

Hello, thank you! Our 4Runner front aluminum bumper weighs about 60 lbs.

Thank you!

Thank you. Our single swing arm option (or no swing) will work with a Gobi ladder, but the dual swing arm will not. We build the swing arms pretty tucked into the back hatch so there is no space to fit a Gobi ladder behind an arm.

@@heftyfabworks Ok cool, thanks for clarifying.

The steel sub-structure is 3/16” and 1/4” steel and the outside shell is 3/16” aluminum.

Thank you! I will definitely note that down for a potential future video.