Video

3:34 shows the zip tie mounts being installed in the exact same place the weather seal contacts. It's incredible that this offical install video doesn't just miss things, but objectively gets things WRONG. And as far as I can tell, there is no way to route the electrical conduit so that it's not just going over the weather seal about 3/4 of the way up the rear hatch. Because as shown at 4:36, the conduit will have to pass over the same place as the weather strip once the lift gate is closed. Having water in my vehicle is not worth relocating the camera. Am I missing something, or was buying this kit a big waste of money? How can the conduit pass from the lift gate to the vehicle body without compromising the weather seal?

I'm looking for one that fits a hitch 2003 Ford expedition that will hold a tire and a gas can.

Did yall stop selling these? I can’t find it.

How much weight can this system take?

can you still tow a trailer/ hitch basket with this on?

I have a 3rd gen 1997 4runner. Which ultra swing should i get?

I have the multi-fit ultra-swing on my 4runner and it bounces like hell going down segmented/rough concrete highways at speed. Any solutions for this or something that might have worked itself loose? Its to the point where I'm worried about the tire mounting bolts snapping from the force while on the road.

I bought one 4 years ago. The pin Is stuck and can't open it now. I'm going to have to take it off and put it to the side. I wish I bought this version :(

Anything for a 2024 Honda CRV Hybrid?

I wish they would make this thing in driver side swing config

Will this be available in a swing to driver side configuration???

Is this road legal in Australia?

Does the Tundra camera kit work for 2nd gen Sequoias?

whats shown is the short stinger? Will short stingers work with the spare tire carrier if we move it over to another vehicle?

can we quit with the wheel strap and press down fork... its junk

Great shit man. Very digestible. Can’t wait for mine to arrive.

Drop your post with the bike on the car...for shame. :)

This takes an about 3-4 hours to install. I just helped a friend install and here were some key things they left out like all the comments state. I felt the need to tell my story for the CZcamss. Let’s start out with the plastic cover. Peal back at least 50% back or more. You’ll need the room. Also when you remove the remove the speaker remove the speaker bracket too. It’s 5 screws/bolts. Once again you’ll need the room. Lastly remove the cap located on the very bottom /underside /of the door when it’s open. You’ll know it when you see it. It just pops out when you pull it. You’ll need all this space to run and see and zip tie the wire. Make sure you have extra zip ties and not the little ones they give you in the kit. So let’s get to the meat of this pia job. One way to run the wire and avoid the window is to run it parallel with another existing wire that runs to the right against the frame. Then zip tie it tightly to that wire. This wire runs all the way to the right and never touches the window. Once you get to the right elbow, followed the frame down to the right and zip tie to the wire or this white stationary bracket parallel to the inside of frame and stay on the outer edge. Once you get to the end of the white bracket loop back up under a set of wires and through the grommet hole/remove grommet. Once you are through the grommet hole you’re good. They could have shown you in the video which makes no sense why they didn’t…. The rest is straight forward. Maybe next time I’ll just do one of these videos…

Can it work with Tesla Model Y?

Dose it auto lock at 90 and 120 degrees opened?

Dose this automatic lock at 90° and 120°

Is it limited to 1 bike or is it possible to spec for 2?

Perfect video to explain everything i asked for, beers can holders were extras

This thing is cool. Do you offer a hunting guide discount?

I have a 2023 promaster that I recently converted to an RV. I installed an aftermarket trailer hitch and planning to install your product to mount a spare tire, and to hook my 5x12 all aluminum enclosed trailer as well. So for my applications, it’ll be the megafit right? Does it comes with spare tire adaptor too?

I secured my bag exactly as detailed in this video. Unfortunately, the straps did not remain tight. After one day of mild trail travel, the bag was loose almost to the point of falling off. I solved the problem by sewing the metal buckle to each of two ratchet straps and routing each ratchet strap around the tire. I ran a piece of paracord through the webbing loops at the bottom and tied that to the bottom of the wheel. With this setup, the straps remain tight, the straps and bag do not move while going down the trail, and is still easy to remove.

I attached the bag exactly as the Rigd video shows. Unfortunately, the straps do not remain tight. After one day of mild trail travel, the bag was loose almost to the point of falling off. I solved the problem by sewing the metal buckle to each of two ratchet straps and routing each ratchet strap around the tire. I ran a piece of paracord through the webbing loops at the bottom and tied that to the bottom of the wheel. With this setup, the straps remain tight, the straps and bag do not move while going down the trail, and is still easy to remove.

Will that hold 40’s ?

On a Sprinter B Van, will this hold the spare tire and 2 large Ebikes (77lbs each) ?

Great idea but boy that’s pricy.

Hi there! Is this a Megafit or Multifit? Thank you😊

Hi there! Is this is Multifit or Megafit? Thank you

Love what yall are doing!! I’ve been trying to get in touch with someone at Rig’d would love to talk about a partnership!

This a great concept, but the back up camera is lost, man the camera is a must when backing up!

Rad design and build quality looks solid. I'll be checking these out for my Runner.

So I have this exact same Subaru and color. 2009 Forester. I went on the link on the description, and it looks like you only have this tire rack for an Outback. Do you not have anymore for other models?

Can I use it on Ausie Thorburn bumper for my bikes?

Did you mention what size tools are necessary to tighten the bolt to the stinger?

I bought a an Ultra Swing for my AEV Prospector a year ago. Unfortunately it won't clear the right bumper tube on the rear bumper. An hitch extender isn't solid enough. Do you have a solution for this problem?

I love my UltraSwing, it’s lived a well traveled life in its almost year I’ve had it. Added the table, tire carrier, gas can carrier, and even a 5 lb propane tank carrier. I bet I’ve recovered six vehicles from ditches and mud holes with it even. The only thing I would want from it now is a way to mount an antenna, which I’m working on anyways. An outstanding unit.

Will this fit a 96 Jeep XJ?

So what are the extra 2 washers and nylon nuts used for?

Motocarriers.... The wish. The Dream

All I want to know is if the swing out portion could accommodate a dirt bike carrier! That would be a game changer

The hitch looks great on the Subie. I’ve been told that any swing away that works on them can also be fitted on a Honda Element. Wanting some clarification here before I order.

On your tire carrier did you have to remove the Bisons rear bumper ring mounts ?

How about backup camera relocation? That’s the little detail you missed which maybe messy for most people

I’m really interested in the swinging bike carrier for my Ktm 500 haven’t seen anyone do it yet but your guys seems the beefiest! The double swing carrier is sweet

Ever used it for a dirtbike 250lbs ?

You should sell it in Europe!