Video

K-MOTOR PERFORMANCE 6AN to 1/4 Quick Connect Fitting Adapter. Can get it online.

@@TheShopLLC40 thank you, very kind

Anytime! Thanks for watching 🙏🏾

Was a 6.0 LS2 at the time. I later put a 6.2L in it. Its still naturally aspirated

😂😂😂😂

literally, thats probably what he did🤣🤣filled it until it was almost at the top then was like "perfect!"

Thanks bro! Check out the build series on the channel 🙏🏾 2 episodes

😂😂😂 we were all dying

We dont gotta worry about that here in Az lol

Lmao german engineering

All the way to the Top of the dip stick 😂😂

@@TheShopLLC40I’m dead asf 😂😂 they said damn I need to go back to the store and get more after the first 5qt bottle 😅

😂😂 they got the 2 gallon diesel jug 😂

It started pushing out everywhere it could 😂😂 destroyed the turbo seal too

2 times? 😅

😂😂😂 cant even blame that. He did 2 oil changes without draining the oil lol

Ima keep them coming wether you like it or not 😂

Yes we did a hell cat swap on a 13 dodge ram, 4-5th pull in on the dyno the sensor started pushing oil

@TheShopLLC40 I have a 19 5th Gen and seen oil the other day around the sensor like it's starting to leak as well thanks for the reply I'm gonna replace it now.

Have to remove the pulley to get the belt on and off

k061080HD gates belt

@@TheShopLLC40 okay i am stuck... so i got the new belt, but now the belt tensioner is laying in front of the supercharger bracket? and it wont push down so that small idler pulley in between the alternator and procharger wont line up and i cant slide that hex bolt in... this is a mess lol

@@sharkykush3583 thanks bro. Cost more then doing a normal whipple or a pro charger. Have to get hell cat timing cover and accessories to make it all work

He’s probably 20-30k into it. Has a forged bottom end and all good parts. Needs a fuel system, injectors, e85 and a upper pulley it will make 750-800 no problem.

I did thats why i had to pull both heads

To pull the cam and knock the lifter down

Lmao even VR1 wont stop these cheap lifters from breaking

Lmao it was hot outside 😂

Thank you!

Thats what a filter is for..😂

Yup we let the customer know they were the cheaper set. We usually run comp ls7 or johnson if we had the choice. some customers don’t want to spend that money or just don’t have the knowledge about the parts.

Lol taking a nap

Hawk was sleeping at the tree 😂 he was making a sandwich. Got him by a fender up top.

We have the matching wheels for the fronts that go on the rear but the car does not hook up 😂. We got a set of 17” welds to help put the power down. Thank you!

Thats the words out the customers mouth. You can i know they felt in & heard it for weeks 😂

The machine shop said they can turn them for me

Harness is the same just had to change to a LS3 intake. On the ls1 ls6 knock sensors under the intake manifold

Thanks bro

@@TheShopLLC40 I’m working on a 6.2 ls you got any videos putting one together ?

@ItsDLove91 LS3 6.2L? Or LT 6.2? Im doing one rn bro ill make a video and post it

@@TheShopLLC40 yea ls3 I should of capitalized LS lol but I’m ready to watch

@@ItsDLove91 my bad i didnt see it first time i read it lol. Ill put a video together for you, doing one with a stuck lifter so i am pulling it apart now. I’ll put a video together and post it up this week taking it apart and throwing it together.

650-700 i believe the customer said when he got it dynoed

@@TheShopLLC40 Wow! Very cool!

Glad we can help out 💪🏾 stay tuned for more coming

@@TheShopLLC40 how about a crank pulley swap in the garage without a lift video on this one? Pulled my Vortech and belt off, then noticed the crank pulley was separating in chunks. If no video possible, any tips or suggestions is greatly appreciated!

I did show it, and showed where & how it goes.

Thermostat housing is feloro 36122 The pipe orings x2 felpro 36068

Thank you man i got a few videos dropping soon stay tuned 🙏🏾🙏🏾

442 is *not* an engine. 🤦🏿‍♂️🤦🏿‍♂️🤦🏿‍♂️

@@yungkidnf you know lol

You sure about that one? Lol google 442

Thermostat is feloro 36122 The pipe orings x2 felpro 36068

Thanks bro 💪🏾💪🏾 more to come

Got to spend 80-100k to get anything newer that makes good power

Sorry for the late reply its actually a k061080HD gates belt

But it has a smaller upper pulley not sure your size but that will change the belt

I'm running a K061140HD on my d1sc 99 cobra. It's making 10lbs

Appreciate that! A spacer would be nice, make the truck look a bit more aggressive

More to come stay tuned!!

Thank you try to give everyone a visual to help understand whats going on while your in the car feeling with your hands lol