Video

Новый комментарий за 6 лет

Do you have a link to that little wrench with those bits ? Or where you got it

nice plumbing but this is a usesless contration. it allow you to burn dirty fuel, yes. but lower the horse power. the efficiency is about the same or slightly worse than stock. remove the "geet rod" and report the diferance it made.

Where did you get the new seat covers they look very nice

Is there a chance you know where to get that steering wheel?

How long does it take to get this motor running when it's cold?

Did you finished it already? Im waiting

Great video thanks for sharing

Great job! My 68 needs the same.

Nunca muestran el rendimiento

I want to do this but Where did you get the pipes/hoses? @logan gamble

How long you had this vehicle and what year is your car

Will it cut grass without stalling out?

You should study the documents and data on the lawnmower conversion of 2008, with just mineral water in carb. 6-7 amps electrolysis through spark plug with magnetic field coil over plug wire to extend the spark time , to about -34 degrees. EGR incereases efficiency. Hydrogen gas and water vapor pressure generated runs engine. see- S1R9A9M9 . Magnets under flywheel provides alternator 10 amps after battery was disconnected. Magnetic field at spark plug tips electrodes. 1.5Millihenry coils also extend spark time were there also, with accessory spark gap and diodes... Voltage pressure depends on ohms resistance of spark plug used. write me...

I have a workshop in India Can purchase magwheel to my car from there ? 12 inch size

Hi Bro am from India !! Where are you from ?

Can i purchase magwheel 12 inch to india

Yo we need more updates you rock

Friggin beauty dude

Hey mate can you show me how you ran you chain

All that talking and still didn’t hear the blow off

Why is it after all this work on getting it to run, No one ever shows one of these ever mowing a lawn?

is there a finished build of it?

Can the geet be installed into a car?

سلام ممنون از اموزش شما من میخوام اینجور دستگاه hho را درست کنم ومیخواهم با آن موتور 125cc را روشن کنم برای روشن کردن این موتورحداکثر چند صفحه لازم است و چه ماده ای برای جوشش بیشتر آب استفاده میکنید ممنون ❤❤

Did you use original bike sprockets? What ratio? Cheers.

You said it man 👍 I know I'm showing up 4 years late to the party but does it still run?

poor Frank

Guess I'll sell my gfb dv+. Because I don't got 6 hours and patience for such a little upgrade. No way I'm moving my turbo either dam idk. Guess I'll just put in dogbone insert and rear anti roll bar. As for the dv I guess once I finish all other upgrades like suspension and visual mods so it's literally the last thing.

Nice job awesome productivo hho

Level 3 suit and engineer suit

Looks clean! Great job! Exactly what I’m doing to my 68 Firebird. Plus the trunk, sound system, ac, and lights/wiring. I’m busy. Lol

I’m about to do mine but my top inlet is straight not slanted

the Velcro is such a good idea

Top Shelf ~ GR8 Job ~

2:14

where did you purchase the center console?

Nice system for dry climates.

Hey everyone I'm looking for a little help trying to restore my wife's 68 Camaro finally got most everything working again and running , one problem I'm having is as soon as I turn the key the temp light on dash comes on and stays on. Car is not overheating and runs great. Now you would think the temp sensor but for the life of me I cannot find the temp sensor there is nothing on the block or on top of the coolant thermostat housing. Any ideas ? It should be located driver side between the block or head and the master break cylinder. Please help

What size bits did u use?

What’s the link to that boost guage tap attachment in the engine bay and can you do a tutorial on installation

This is good design but Where is oxygen outlet? Please explain .I am sure there is one .

My uncle had one in Texas,cooled much of his double wide mobile home. Loved it!!!

Do you know how to wire it to a 2018 Chevy truck. I got this kit from labellashho but their extremely rude on helping out. They got really bad customer service..plus their Manuel its so hard to understand. A 3rd grader can draw it better.

Hello, I am a viewer living in Korea. I am operating the 2016 vw jetta mk6 facelift 2.0 tdi premium model. I am looking for a genuine spring exclusively for gli, but it is difficult to know the item number of genuine parts because the 2016 vw jetta gli model is not imported to our country. I asked the service center and they said if i check the overseas gli's VIN, they can check the item number of springs, so I need the VIN of the 2015-2016 vw jetta mk6 facelift gli model.. If you don't mind, can I ask you to check the your gli's VIN? Don't worry, I won't use it for anything other than checking the item number. plz, i'm in desperate need of item number of springs.

Good job

what throttle body do you have?

do you have the link for the valve?

Logan, good job man! That unit looks bad ass cool 😎

Hi did you get stage 2? Ive heard that our gen3s 2014 and up have very weak turbos and they tend to break easy at stage 2