Video

hello sir i would like to ask question related to this topic my router and desktop is connected through lan cable and in my router 802.1p qos value is set 7 by me and in windows GPEDIT POLICY my DSCP value is set 46 for online gaming application so is this good marking done by me ?. my main goal to achieve is low latency in gaming

it would be nice to mention what are disadvantages of this setting, for example MAC address flapping observed in logs, as MAC ageing will not take place with this fast change.

Thanks, we learn a lot from you Bhai 🙏🙏

Thanks bro. Needed this for work

Hi , can you share the PPT ?

nice explanation

Thanks for the great work Bhai..

Great thanks sir❤

Sir AWS networking course needed

Sir, I’m confused about one point. When applying a route-map, why did you do #route-map MED permit 10 #set Metric 100 and no #match ip address command and no ACL either? Setting the route-map without an ACL, and without a matching command, what would be the result be?

Thank you so much sir! BGP MED is something that doesn’t get much attention!

nice bro

What books did you use / resources you used to learn this material? Do you have your own course / telegram where you teach people? Also thanks for the videos keep them going! Thanks!

Thanks for always dedicating time to me for us these videos #ccnp#

Nice video

Good teaching

Brilliant!!

Thank you sir!!

Excellent explanation

talk slowly. nice video

Kindly do more videos

This is the kind of content that should be trending on CZcams Thanks Bhai..

Thank you so much. Very nice explanations. need more videos.

can you make a video that routing protocol not advertise gre tunnel. I faced error in that.

Very good sir . exllent but slowly teach

Very nice video ...keeping it short and simple

Thanks for the lesson

Would vrrp increase overhead for primary switch

Is this cisco switch? Would the basic concept apply to Aruba switch?

Explanation is good. But my next question is - How many times did Selvajegan speak word 'so' in this video? 🤔

if loss bpdu from switch B , how will get loop, please let me know

Hi Selva, Your videos are so helpful. Thanks. Glad that you are on udemy, 😅 I have a problem in my topology, kindly let me know if you have any ideas to debug. Issue description: Connectivity issue with clients and VRRP Peer after upgrading from older firmware to new firmware. Two core routers are available. Core-1 as master core-2 switch as backup. This is configured as a VRRP peer. Problem is that, clients were not able to reach VRRP peer after upgrading to a specific firmware. In the switch, cr-1 and cr-2, mac and arp learning is happening successfully and after clearing arp, it-was able to re learn the mac addresses properly. Facing duplicate address issues on many vlan addresses. Didn’t see same addresses configured on master and backup router. Workaround to restore the clients connectivity to vrrp peer is : 1. Flapping the respective ve ,interface clients connects to. 2. Downgrade back to working version. Any idea how to debug this issue ? Please let me know, if you are on discord.

very well explained!

Your lessons are very indian friendly with super explainations. Thanks anna 😊

Thank you very much. Clear & concise!

it is not mandatory to configure loopback address. Is it?

please make one similar lab for ospf

Great work sir make more videos

Not understandable ! -Accent too strong and talked too fast

Thanks this is very good explanation 🙏

Wow it helped a lot 🎉 thank you ❤❤❤❤❤❤❤🎉🎉🎉🎉❤❤❤🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉😮😮😮😮😮😮😮😊😊😊😊😊😊😊😊😊😊

🎉

where do you rush?

short and exact

Thanks for putting this topic in a very simple explanation

Thanks

Understood everything. Clear explanation with examples helped a lot.

Thank you sir

Great explanation and hands-on. However, i do not want to advertise certain prefixes. how can I get this done.

Thank you very much