Video

How to you test a can bus if There is a gateway module?

Hey brother! I just want to say thank you! This video is what fixed my 09 silverado. I did a motor swap on my lc9 and couldn't get it going for 4 weeks . Trouble shooting ext . From a cut harness going from my engine to my fuse block. Power distribution block. Refined all the pins . This was my last hurtle. And you nailed it! Thanks again. Your video was bang on

HI there, I saw your video on youtube about TCM programming . So i got a few ford fiesta tcm and mazda 3 tcm. How can I test if they are programmed properly and if they need any programming how can i do it. I can buy the hardware and softwares needed. My biggest concern is how do I diagnose/ program the tcm without fitting the tcm to the car. I saw a lot of videos on youtube where they plug the J-box to the car to diagnose/ program. I would be happy if you could help me out. Thank you Fernando

What u do to fix it boss

Not a popular way of framing it, perhaps, but an aircraft is indeed a vehicle. 😂😂😂😂😂😂

This is for the 2005 Pontiac Grand Prix 3.8 v6

My no start comes from a new computer at first installing the unit all the dash lights comes on but when time to start all lights goes off except the engine light the first couple of days when trying this then just last night the disabled message showed up now. on the old computer there’s no problem with starting at all so some how the computer is having an issue with letting me start the car

well done man very informative video thanks...

What diagnostics/programmer are you using?

Thanks man. This was really helpful.

we just had a 2015 equinox, installed chain, had constant poo17 code, checked timing 3 times, engine ran great, couldn't get light off, saw your video, ordered an exhaust cam from chevy and installed it and check engine light is off, we couldn't believe that the reluctor could slip like that. Thanks for the great job explaining it on the video

Where r you located?

What city are you located in

Mine does it as well. It’s the harness in the driver door. The repeated action of the door over time is breaking wires in these harnesses.

♥ Thank You ♥

Question. When I look up 2013 Escape fuse panel it shows a totally different fuse panel? They are the little push in type fuses, instead of the terminal inline fuse?

This seems to be a very common problem.

Thank you

2018 Yukon Denali with P257D code. I just did the component test on the installed hood latch. Open and closed the reading was in the 700s. I bought a new latch today and it is the same. Am I missing something?

Thank you so much Sir ! This is the only video on CZcams I've seen about this issue I had already replaced lots of things on my 2013 Malibu This High pressure pump video of yours saved me God bless you! And once again thank you so much! Greetings from Tijuana México ✌✌

I have a Mercedes c300 with a crank no start, it does detect rpm but no injector pulse, and intermittent spark. Seems like the same problem, but it doesn't run with the intake or exhaust sensors unplugged.

Are you using a vcmll connector or just a data cable from the laptop to the car?

I have this code. My 2018 Silverado LT 4.3L V6 4x4 crew. With 119,900 has been amazing. No problems. Except I have had to remove and clean the hood latch switch several times, about every other year, it seems now it is so mad it is showing my engine light…

So my 20 T250 is have a similar issue. AC stopped, blower works fine. Went through all the fuses and relays. At times the controls would just go out and come back while driving. Would you lean more towards the controls with the knobs?

great stuff very helpful

Thanks Brian, great video!

Good morning, please short term positive 20 percent and long term negative 28 percent, please the meaning

Great video but you're too judgemental.

Hi my name is Luis I have f250 whit problem no crank no start and on Custer I have message starting system foult can you help me

Hey brother! I am currently attempting a 4.6 to 5.4 swap on the same truck. Is it possible to flash my 4.6 vin onto a 5.4 computer? Or just flash the existing 4.6 computer with 5.4 configuration?

okay let me ask you this what if I don't have the IDS OEM tool I have J 2534 you think it will work ?

Hi sorry to bother you at this time do you have a link or video how to install Ford IDs please let me know and you have a good night

Good job, bro!

Thank you very much good trick to signal out a bad computer

thanks

awesome, thank you for sharing your time and knowledge

Yes Fuel Trim is Very Complicated to understand but with the Hands-On example how about ' Controlling a Model Car You put Light in ~ a Dark Tunnel dude! 😮👏

Can you use a refurbished/reprogrammed computer from a 2008 Jeep Liberty on a 2010 Jeep Liberty?

So complicated.

I don't know how this video helps any body. What's the problem.... What the solution.. Was there a fuel pump issue... wtf

Excellent l really like the live demonstration.

Great video! I learned a lot! Thanks for taking the time to do this.

Hey Brian, how do you get rid of a PMI failed message? On FJds won’t let me do any other function till it that error is gone.

Hey Brian how do you get rid of a previous PMI failed message using ford Fjds?

This video was excellent!

Nice analogy with the r/c car. Thanks for posting👍

Hi there, excellent video and I have subscribed! I have a quick question if you don't mind: I have a 2012 Altima and it need an ECM and the service number is MEC112-130 B1 2313A but i can only find ECMs with the same digits except the last 5. Do you think it will work after I reprogram the keys and VIN? I was told the last 5 numbers don't matter but I'm unsure on what to do. Thanks again for the video :)

BEING IN THE TRANSPORTATION REPAIR FIELD FOR 50 YEARS NOW AM STARTING TO UNDERSTAND FUEL TRIM PLUS THE REASON WHY THE READING ARE POS-NEG.AII THIS I KNEW I HAVE THE UNDERSTANDING,I FEEL IT THE PERSON WHO TEACHING IF YOU CANNOT GET THAT TECH TO SEE ARE UNDERSTAND WHAT YOU TRYING TO SAY. YOU ARE WASTING HIS TIME& YOUR, PLEASE KEEP-UP THE GREAT WORK, [ DADDYDAVE 707 ]

Hello sir . Great video . I’m starting watching your videos . Question do we need to add the 2 banks to see results or just both trim at 1 bank ? I’m sorry I didn’t get that part. Thank you sir .