Video

Hobby plastic .... it is a bit soft and spongy.

Not this time, it was a one day trip. I did go camping several times but i did not record videos. I only have a short on my channel eith my trip to Transalpina Kings Road. Hopefully this year i will get to do more camping.

Da, intr-adevar e o masina buna si e destul de simplu de intretinut.

In the video I have step up and step down dc-dc converters installed. Now i also have batteries installed and i run them with a 3S charging board which outputs 12v then i have step down converter for rpi. I also have a step down for charging (charger gives 19.5v) and it converts it to 12v for 3S board.

Hi, yes, it works just as the original.

It is running for 3 years now... no issues so far. I checked it from time to time.

I believe iti is called ATV Launcher

I dropped it... my battery has not yet swolen...but i am expecting that to happen. I try to not to deplete my battery and when i don't use it, i shut it down and then hold the power button for 10 sec to completly shut it down...otherwise it drains mai battery and it heats up (i have done all bios upgrades and stuff but still drains the battery). But this habbit has kept the battery going well so far.. I still get arround 4-6 hours on battery.

This is the name on aliexpress: 13.3 inch display capacitive touch module kit 1920x1080 IPS 2mini HDMI LCD Module Car Raspberry Pi 3 Game PS3 XBox PS4 Monitor

I had no issue with my keyboard. The video cut was just because i switched position of the camera. Maybe you should double check the cable. It may not be fully inserted. Hope you can find the issue.

metoo， I bought a new one try to install but it doesn't work. I'm in despair. If u have any solution please share it with me.

my keyboard 's backlight also doesn't work. it just flash a second. I've tried all drivers and make no difference

@@kaorischannel also my keyboard lights up for a second on startup and then nothing, i reinstalled all the drivers, i reset windows 10 to factory settings, i bought two original keyboards from two different lenovo resellers because i thought the first one was defective, instead both have the same problem, we worked in a repair shop, so we are not "simple" users and we have tried them all and I can't understand where the problem is 😓😓

@@HokutoLegend hi dude，I solved half the problem. the resolution is putting the clip on the connector down (to the left).Then your wacom device is usable and keyboard will light up. But my keyboard still can't use. I'm sad. I'm doubt myself.

Hi, i have not replaced my screen yet. I found replacement screen on Aliexpress. You should be able to replace the screen in a similar way as the keyboard. Be very careful when inserting spudger not to touch any cables and you should be ok. Here is a link of the display i found. Hope it helps. US $50.21 | For Lenovo Yoga Book YB1-X90 YB1-X90F YB1-X90L LCD Display Digitizer Touch Screen Glass Panel Assembly For YogaBook LCD

Maybe it could be replaced but it is quite difficult since the emmc module is soldered to the motherboard. It may also have proprietary setup.

I have not dissasembled my screen yet (and hopefully i won't have to :D). I've done a quick search on youtube and there are a few videos about how to remove the screen. Maybe you can find the solution there. Good luck! ;)

I bought it from Aliexpress. Please check the comment section for more details.

Nice! Should be a lot powerfull than my RPi laptop

Thank you. I got those hinges from an old Dell Latitude D530. ( the one i disassembled in the All in one PC video).

Hi, I do not have the measurements for it. This project is still ongoing and what you can see in this video is not the final product. I have done many changes to it. Hopefully I will finish it soon and post a video about it. Sadly I just did not have the time to record every step but I am making a 3D model of it and I will post a link for the model as soon as it is finished.

The layout is different. You should buy the appropriate model for your specific model. The heatgun should be set to max 200 degrees Celcius and slowly heat it up. A hairdryer should also be good. The most important thing is to heat it evenly arround the edges and be carefull not to insert the tool more than 5 mm. There are very sensible wires arround the edge.

I put mine on the hot bed of my 3d printer. 70 degrees C for 10 minutes works fine.

i bought it on Aliexpress. Please check the other comments for details.

It was about 50$

yes, the windows version has marked touchpad buttons and the android one has only touchpad. I don't know if they are compatible with each other

no they're not comparable

It is a good ideea. I have installed chromium OS an Fyde OS on this raspberry pi laptop and it runs quite good (it has SSD, 1080p and touchscreen). I am currently still working on finishing this laptop but time is an issue for me. Maybe after I finish this one i will build another. When it comes to manufacturers and Chrome OS i believe the issue is more with users that are not so keen on moving to another platform. Most people I know won't try another OS since they got used to Windows or Mac OS.

Sir pls reply and how do I connect directly because my tablet battery is so weak

Yes, you can. You need a 3.7v power supply.

not really... broken android tablet motherboard into wooden box :D + minor teaks here and there

@@diytech2001 can it be done with old broken tv

@@diytech2001 can we make it with broken mobile

@@kathiravantemplate9032 Please check the other comments. I have already discussed this topic.

@@diytech2001 okay