Video

Going to to rebuild mine. Everyone told me it cannot be done blah blah. This man proved the world is not flat

Hey dude I wanna say thank you Because of you I was able to reinstall everything inside so I kept watching since your first video about the primary and secondary pulley ensemble thank you I know it’s hard recording a whole process but you did a great job So this is my first cvt JF015 rebuild with no experience or knowledge at all but it’s was fun and it took me long time but the second one it’ll be easier more familiarize to it So I’ll put it back on soon and I will stop by to let you guys know what happened hopefully it’s working perfectly. Bye 🤞

Hey bro I have a 2017 nissan vers sv and my transmission took a carp is hard to replace the parts?

Absolutely a life saver.

Are the 3 identical solenoids interchangeable? I bought some aftermarket solenoids and they have different part numbers.

Cool. Who would do something as good for my car?

How do you get the solenoid pin out in the first place?

How do you get the solenoid springs out in the first place?

Where did you order parts for rebuild

Good morning, it is the same procedure for any Nissan Versa

Bro thanks for all this videos Question did you resolved the the problem once you putted it back on?

Hey mate, do you know what size and thread the test ports are on this? i want to test my pressures with an external gauge

Gracias por compartir

question about the forward clutch pack after both snap rings and clutch plates removed theres a gasket at the bottem does this come with the master rebuild set?

Fucken awesome dude

Do you have to remove the driver side front tire to get to the transmission cooler filter?

Great video thank u

here are OBD2 fault codes for my 2015 Nissan Versa Note SV: 1.) P0963 - Pressure Control Solenoid A 2.) P099C - Shift Solenoid G 3.) P0999 Shift Solenoid F 4.) P0967 - Pressure Control Solenoid B (Primary Pressure Solenoid)

Could I use another transmission from Nissan and just change the bell housing I hear if the y12 and the juke am just not sure working trying seems to be cheaper

ooo make sure not to get any anti sieze on your rotor and brake pad.

Excellent instructions! Great job!

Where did u get the parts?

Great video, it’s rooster comb

Man I love your attention to detail and you are a saint for sure. I buy Alot of em and sell em and I'm tired of spending the jack for a used good unit when I can spend a fraction and rebuild em myself.

I'm really satisfied with Your training thank You.

Followed everything and transmission still slips 😭

1:43 I saw another video were it came with 2 little o rings on the top holes. 2 top holes for the variators

The transmission have to come out the car to replace this kit?

Thanks for video

I replaced my valve body, now my car won’t move. Any suggestions?

Can we dismatle and install for this part without remove transmission down.

Great job, thank you very much young man

Super cool! Thank you for sharing

Great video. My only comment is when you're doing the final fill of the tranny. You'd probably get a more accurate fluid fill if you were to have the car level by jacking up the rear axle some till the car was sitting level.

I rebuilt a few Ford and GM automatic transmissions back in the day when I used to screw with that stuff. Your videos are excellent and show the real life experience of messing with this shit. I agree with your point on another of your videos that pulling and reinstalling these in the car is a much bigger pain in the ass than the bench top rebuild. Great videos!

Very nice video. Love the spicy talk and commentary. Perhaps the best video on rebuilding these piece of shit transmissions I've ever seen. Great job!

Great accept for the profanity.

Hey man!!! is there any way that you can provide the link to purshase the parts!!! thanks!!!!

You did not mentioned the bolts torque for the transmission pan (total 15).question: is it mandatory to replace the transmission cooler when you do this kind of job?

Ratio control valve uses spring on it!

Can I use sealant 5999 gray vs 5460 pink? Thank you!

Aidez-moi s’il vous plaît, j’ai un problème avec ma mission sentra cvt quand je passe en vitesse (R) et (D) Lors de l accélération la barre ne dépasse pas 1.5 contrairement au parking sa ronfle bien Pensez vit que c’est un problème de la pompe à huile ? Besoin de vos idées

Excellent job you did. Thanks

I have a Nissan versa al 2012 al .need replacement valve body how order the right part

magnifique video

Ok f. Line in and out please very confuse

merci pour la video

How many quarts?

هل يوجد لديك فيديو خاص بنسيان مكسيما موديل 2008 GVطريقةصيناتة قير

You are a good master! You have a very good and detailed video, it helped me a lot. Thanks for your work! I know how difficult it is to work and shoot quality videos, it takes a lot of time. Carry on, good luck, friend!