Video

Impossible to remove the wheels. It’s not that easy like he shows

Thanks a lot ! In my case, removing the wheel is not needed ...

Do we really have to remove the wheels to open the K7? I have a K7 Smart Control and I can't remove the wheels...

How in the hell did you remove the wheel clip?

AGAIN: YOU DON'T HAVE TO REMOVE THE WHEELS! (See comment 1 year ago) You can REMOVE THE black part of the housing including the wheels. Take a long (4-5 cm) torx 15 Bit and use some long bit adapter/screw driver to remove the screws. Good luck.

Thank you

5 on each side sir you show only 4 !!!! Big mistake !

Thanks for this, My Henry died and I initially thought it was going to be motor or switch failure, both these checked out ok. Saw your video and followed it through to find the plastic molded plug was at fault. I cut it off and replaced with a normal one and Henry is now back working with full force !!

climatizarea KLA. H-MT/AT) COMUNICARE motor AC. B1040

Many thanks for this. HOPE all is well with u.

Cannot you repair my own

My K7 just fell into a river (oops). I was hoping to find just this kind of instructional video. Thanks! 🙂

So far it looks like it is a case for my hetty too.. it is power on both cable end.. I don’t have another power cable to test if is the problem but the video is super helpful

OMG a test with a neon screwdriver

Thank you for taking the time to share this video, it’s a great help. Much appreciated

What number of key did you use for the fist step?

No ever would have suspected the cable, so many thanks for this! This was my problem - previous cable replacement at a shop had not put the cable properly in the guide, so pinching it, eventually failing. Luckily I only had to trim a short piece.

Very useful, thank you!

Muchas gracias por su ayuda, me a servido mucho. Soy de España, Andalucía, Cádiz.

You dont need to remove the wheels. Just need a long shank driver for the Torx screws. Anyway removing the clips destroys them. Also removing the power switch knob first makes it easy to reassemble. Just prize off the knob. Otherwise this is a piece of cake to do.

Those wheel holding clips are a fckin pain in the arse to remove... actually everything else is easy but those two mofos drove me crazy

Really helpful, many thanks 👍

I have a Nutri Ninja Pro that I purchased in late 2019. Unfortunately, they have made removing the lower seal (2:10 in this video) impossible (by adding a pin that makes it impossible to rotate). So, while this video is FANTASTIC, it probably won't work on later models. It's really too bad, because the bearings could have been replaced at reasonable cost, but this configuration forces the consumer to purchase a complete, new blade assembly (for about US$25).

thanks for the help.

in the kitchen... Lol 😂

In respect of the removal of the pesky spring clips holding the wheels to the shaft. I bought a T15 screwdriver with 4 inch (10 cm) shaft. A local engineering works extended the shaft to 12 inches (30 cm). With this I was able to remove T15 screws (second screw from base) behind the wheels. Quite likely the Karcher workshops have an extended T15 screwdriver. Placing a magnet against the screwdriver shaft will retain the T15 screw to the screwdriver. Hope this will be of use.

Thanks for very clear operation. The difficult part of the job is removing the wheel clips, the aim for this step is to remove the 2 screws beside the wheels. actually the wheel does not need to remove, if you can find a long screw driver, or you can creat a long screw driver to remover the 2 screws.

Thankyou! I just ordered new set of knives. Had no clue how to change them until I watched your video. I think one of the bearings is gone also. This is very helpful.

No, that part in the middle doesn't come out of mine, it wants to break before it moves. WHY is this thing so pants to do... thought I'd found the light, when all I found was pain.. :( help me obi wan kenobi...

I went the magic bullet route and fell short of removing the bit that holds it. this is good to know, cheers! now I can get that crap put of the ring of the blade. hopefully.

Hey, how do you reconnect the actual high pressure hose back to the machine. (The connection near the hose real)

this is complete bullshit, the grip washer holding the wheel on has to be virtually destroyed to get it off, you don't show what a ball-ache they are to remove.

thanks I was looking around the net on how to get the blade off.

Many thanks. Saved me a huge amount of time. Some tips to add to your great video: - the wheel push fasteners can be removed with a small screwdriver and light hammer. Drive the screwdriver between the teeth of the fastener then lever up a small amount. Move to the opposite side of the fastener and repeat. Keep repeating until the fastener pops off. - you’ll need a Torx T15 long shank screwdriver with a conventional handle. Torx screwdriver bits won’t work, T bar screwdrivers don’t have the room to rotate. - like others, the fault with mine was that the vacuum tube to the detergent bottle had disconnected. I used small nylon tie wraps which seem secure. Others have used clamps. - on mine the high pressure hose reel pulled away from the brass shaft complete with the T piece. All seemed fine on reassembly. Hope that helps

I did the first and second part.( I unscrew and take out that black plastic piece) but I couldn't pull the blade as you did.

the blade didn't come off. any suggestion?

It uses 8x19x6mm bearings. They are $5.49 on Amazon. www.amazon.com/uxcell-698-2RS-Bearing-8x19x6mm-Bearings/dp/B07T19RZLX/ref=sr_1_3?dchild=1&keywords=8+x+19+x+6mm+ball+bearings&qid=1600640759&s=industrial&sr=1-3

Thank you! Excellent.

TWO angry COMMENTS ! THERE ARE 9 screws, not 8. You can imagine my frustration after taking out 8 screws and nearly wrecking the case trying to pull it apart with one still in place. You do not have to take the wheels off and you will NOT do it with a little screwdriver like you show as if be magic.

The only difficult part of the job is removing the wheel clips and you don't show that.

Extremely good video. I had problems removing the spring clips holding the wheels on to the axel. I opted to create a long screwdriver that would reach the screws behind the wheels, removing the wheels is done only to access the screws with a normal screwdriver. Like others my problem was the vacuum pipe had become disconnected, if it happens again I will add clips. When replacing the cover make sure it’s perfectly positioned before replacing the screws, I had to remove it again as the area around the power switch was not aligned correctly, also I found it easier to keep the cover aligned correctly by replacing the screws at the top first working down towards the bottom.

Hi, i have a question. Can i remove the part below the wheel without disassembling the one on top?

Thanks, this was very helpful. I was able to replace mine 👍

Very Helpful. Can you please show how to open regular K7?

Thank you 👍👍👍

Thank you for sharing. Very useful, except where to buy replacement bearings? :-)

When you record video on your phone, hold the phone horizontally to get a 100% full screen recording, you only got 30 percent holding vertically

Its not working at my home because of lessvoltage is there any solution

Very helpful thank you!!