Video

I also thought they had the manual on their website, at least this is whatI remember

Hey mate! I hope all is well! I miss the hobby a lot and hope to get back in to it at some point... Enjoy flying and fly a pack for me too!

Yep, I use gimbal protectors :) or the case itself of course

Hello! I barely have the time to fly a whoop once in a while but I don't want to quit completely. Not sure when I will be able to get back to testing stuff though...

Hello! I doubt those power pins on the board can be switched off. You would have to wire a small switch or pushbutton to the power cable of the led rings...

Hello! I haven't looked recently but there were no multi-color-LED options last time I checked. If you need a specific color that is not available (when I made the video I think they had blue and white only), you would have to desolder the stock LEDs and solder your own, which will be a very tedious task.

You're welcome!

I hope you enjoy it as much as I do!

@@muteFPV thank you! I'm partly blind. it also helps me for daily stuff sometimes. I'm 51 years old. i lost my vision 10 years ago. since than i couldn't solder etc. but these days hot air solder, microscobe and other stuff helps me back to the stage :) i like vintage 8bit computers. I'm lucky that they are bigger pcbs bigger items on it. easier to work with them with these tools. HDMI out is also great for big monitor and OBS. there are many better models out there but of course they are expensive. I've paid 135 usd (4500 Turkish lira) and I am happy. thanks again i have a quick question if you know it. when i connected HDMI, internal screen goes off. do you know that is it possible keep it on while HDMI connected to external monitor? thank you

I don't think it can work with both monitor + hdmi output, I will have to check mine when I get back from holidays

@@muteFPV thanks. I'll appreciate. have a good holiday :)

❤❤❤❤

Thank you! You are right, I agree that it sounds far from natural and pleasant. I was experimenting and it was the best result I could get back then (with a paid service, the free voices were even worse!).

same here, I tought it was broken, like my heart... because I have no girlfriend, but I least now I have throttle

Thanks for watching!

They were intended for 3" and 4" but it depends on so many things (number of blades, pitch, tune, overall build weight etc). Did you get them brand new?

It weights 530 grams. I have used several props 3 inch and 4 inch with 3 and 4 blades. Changing props make difference but not too much. I am not good at pid tuning maybe the problem there.

And yes they are new

Hello! Alive and kicking but terribly busy :(

​@@muteFPVplz reply ..website to know distance that an Fpv can cover

rahul what do you mean? the rc signal or the video signal? what kind of website are you looking for?

Plz reply ​@@muteFPV

I will give you $5

Check my TX16S mods video series, you will find plenty of ideas for your radio, including my switch covers (they were made by Hawk Creations / HawkRC)!

@@muteFPV thanks a million

Thank you very much for your kind words!

Thank you very much!

Hello! Please check the TBS data here: www.team-blacksheep.com/vtx-table-for-betaflight.txt

@@muteFPV but is it valid for v1.0 too?

I don't think I will get my hands on that one, sorry!

If your radio is exactly like mine, you will need to disengange the self-centering on one stick and engage it on the other stick (check @ 1:02)

Thank you!

I am happy you found it useful!

I totally agree! Sadly there are not many options and color-matching different orange parts is hard.

@@muteFPV Yes. but thinking the Logo is Already orange its a good match!

Do you have a link for the Orange Switch nuts?

Can't satisfy everyone's taste, you should try it yourself and find out if it is easy or not. Until then, feel free to turn off the volume on your device, all the information you need is in written anyway.

It has been quite a while since I last looked into these but yes, they are both the same and you only engage/disengage the self-centering. There used to be a different gimbal with less throw (travel) for the throttle stick, if you want such thing make sure to order 1 standard and 1 for less travel, otherwise get 2 standard

@@muteFPV Thanks for the reply. Appreciate it.

Do you mean the "LED Foam Spacer" Radiomaster has on their website? Or does the gimbal led ring set now come with foam pieces?

A3 performed better in this specific test

@@muteFPV thx !

I am glad you found this helpful!

I wish I could give you any feedback but I have not tried or tested the A30 connectors

@@muteFPV Can You test BT2.0, gnb27 and A30 please? I am waiting for Your video :) What do You think?

it is on my to-do list if I get back to making videos :)

@@muteFPV you do such an informative content in the best possible way without unnecessary talking :) do not give up please

Thank you very much!

I am not familiar with the exact circuit limitations inside the TX16S, it has reverse polarity protection for the batteries so maybe it has some overvoltage protection as well (hopefully). Please contact Radiomaster tech support directly, to get the most accurate reply and guidance.

It is a fairly easy mod and the battery life improvement is massive, let me know if you need any help

@@muteFPV I have the nessary batteries but not the 3D printer or sauthering machine. Do you know what type of services would do this for me?

It will be easy to find a local business / hobby shop / person to print the design for you, it is an easy print and should not cost much. As for the soldering iron, it is an absolutely necessary tool if you are into this hobby, so I would suggest that you get one (preferably with adjustable temperature) and begin practicing.

@@muteFPV if I buy all the necessary items could we FaceTime and you give me a step by step! :))) please hahaha god bless

Sorry I don't have the time for that. I believe you will find all the information that you will need in my video :)

Aside from the current rating of the cables you use when wiring the adapter, I doubt that your car has such a high current fuse for the cigarette lighter. Does it? I think usually it is around 8A

@@muteFPV no idea tbh. I just saw a few car lighters with already built in fuser and 12awg cable so I thought to just get one of those and add the xt60 connector. Skip the hussle😂

You're welcome!

Hello! I have never used them

@@muteFPV ok then state that in review but do not just ignore items in the box.

They are already applied on the gimbals right out of the box, you do not need to use them when buying the AG01 gimbals and there is not much to say about them.

​@muteFPV one is a grease and one is an oil.

It is usually already soldered on the multirotor, but if you are building one yourself I am not recommending a crimped PH2.0 connector. Find out why in my video here: czcams.com/video/jscLabUvLPQ/video.html For footage on soldering a PH2.0 you can check this build: czcams.com/video/bfir1S5SF0M/video.html

Thank you very much!

I hope so too, thank you very very much!!!

You're welcome, I am happy you found it useful!

Sorry for the late response, never had the chance to try the Boxer :)