- 11
- 56 584
Brushy Valley Shed
Registrace 24. 05. 2021
I’m always into something. Keep checking back and you may find something interesting.
Scag Walk Behind Mower Engine Replacement (do this yourself and save money)
Our Scag SWZT 48” walk behind mower needs an engine replacement. Very simple fix, I highly recommend doing this yourself and not paying a repair shop.
zhlédnutí: 5 455
Video
This Failed Part Prevented My Mig Welder From Working Correctly
zhlédnutí 84Před 2 lety
Shielding gas solenoid failed on my Hobart 185 welder. Bought the part and fixed it quickly.
Getting the 72” Grasshopper DIESEL up and running for spring mowing
zhlédnutí 5KPřed 2 lety
Brought this 928D down from dads farm to get it ready for his first spring mow. Started with fixing the alternator bracket. Then tightened the ROPS and sharpened the blades.
MY 25 EVINRUDE IS NOT RUNNING
zhlédnutí 24KPřed 2 lety
25 HP evinrude has no fire let’s try to get her running
Narrowing a snowmobile trailer?
zhlédnutí 119Před 2 lety
Friend of mine ended up with a snow mobile to haul his raft for guided river smallmouth trips. The trailer ended up being too wide for his garage so we’re cutting her down a little bit.
Skeg still good ?
Last I saw it was still there
Petrol powered Bay blade
I have a 1995 721d2. Engine runs great. Deck is wore out. Would love to find a powerfold deck or know what needs modded for the powerfold.
Pretty sure the 721 has the Gemini transaxle and I don’t believe there are remote controls for the power fold. Now the later 7 series had an electric actuator for power fold which could possibly be bolted up. Last actuator I bought was $600 and that was in 2014 so I’m sure they cost more now
Idk if you still have the boat years later but those motors have a tendency to blow the top crank seal, I’ve replaced 3 across the 4 omc25’s I’ve had from that era, after replacing the motor starts easier and doesn’t hit and miss the top cylinder it always runs on both
I love that muffler that goes sideways - very nice.
How much u sell the boat for?
In the early 1990’s evinrude started their death throws no primer on their motors no air silencers the motors ran good heck I just bought a 25 evinrude low hour freshwater motor it runs great
Los perros siempre queriendo calmar el pedo jajaja
Dude, that's a great trick. I've never seen it
I learned to rub a folded brown paper bag through the points, not just the sand paper. Sanding makes the surface of the points rough and it will burn faster, you will have to redo or replace points.
Thanks for the tip
Hi, I have a question. Do you know if kawasaki FS481V engine it fits kawasaki FH541V all works??
If you can look at the 481 in person I would measure the mounting holes and the shaft size to see if they match
Hey thanks for the video. We just did this and the pull cord won’t budge. Any ideas for trouble shooting?
Pull the recoil starter off of the engine and see if you can roll the engine over with a wrench. I had that happen before and the starter was rubbing the engine cowling.
What year is the motor?
1976
Top.. de São Francisco, Brasil. parabéns pelo vídeo..
The 900 series is very poorly designed and if you like working on your mower this is your machine. If you just want to mow go with 700 series. Mine 900 is broke more than running and I just mow my grass. 200 hours and been in the shop for months! My 700 was bulletproof, stay away from the 900 series.
Someone just gave me a SWM-48 that was not in running order. It doesn't appear to be seized and I don't see any blown cylinders (it's still sitting in my F150). I'm trying to figure out where to even start ... I have a DR Field mower that I replaced the engine on, but I can't seem to get the wiring right to keep it running so it's sitting in my garage while I decide on the next steps for that one. So right now, the decision I need to make is which one to work on first. I've downloaded the SCAG manual and I'm looking through that first since I don't even know how to see if it should run (an older lady gave it to me and said her (presumably) teenage son had said the motor was bad ... no, I don't want to just trust that so I'm going to do a little troubleshooting first. If anyone has a troubleshooting flow chart for a SCAG SWM, please post it or send me a copy!
Oh, and I should have added that I coincidentally was given a Husq riding lawnmower with a 26 HP Kohler motor (the mower had a bad transmission and was stupidly expensive to get fixed according to my father-in-law and, since he knows I'll try to fix anything, it's another thing in my garage ... practically killed myself getting it off my truck because he hadn't mentioned that he'd disconnected the brakes!
I have one of these and a hydronic motor went out.
Any ideas on replacement/ repair ?
Is it a 727? They had the Eaton Gemini trans axle. Pretty easy fix 9/10 it’s usually the check valves on top back out and let fluid bypass the pumps
www.eaton.com/ecm/groups/public/@pub/@eaton/@hyd/documents/content/pll_1620.pdf
Grew up right by that boat ramp. Used to take my jonboat there to work on it and test it out!
It’s such a perfect ramp for that! Well, Except wake boats😂 the ramp isn’t a steep enough angle. Totally ate the trailer with my prop.
Btw what year is the 25 hp evinrude as I have a 1973 25hp evinrude 25353 Chris from OHIO 🚤
Your a city boy and definitely a Democrat. What a jerk
I should probably floss the points on my 25 soon .good video thanks
Point flossing is key😂 thanks for the feedback brother!
Good luck my new 900 has been in the shop for over a month, worst buy I ever made. Low power poor quality machine.
They’re absolute garbage… Dad has this one and another one up at his farm. He loves them, but that’s because I’m the one who works on them.
That bracket broke because the pivot bolt is loose. If you don't tighten that pivot bolt, the bracket will break again ..
Good stuff. Where'd you get the engine?
www.equipatron.com I received the engine 3 days after ordering. I highly recommend ordering from them.
@@brushyvalleyshed690 thanks, brother
Which spark plugs does it use?
I’m an ngk fan if my memory serves me right I believe it was a NGK B6S 3510
Makes me wanna go floss my points.
It’s the best way to get your day started 😂
Wich year those the outboardmotor come from?
I believe 1976
Unfortunately, that flywheel nut should not have come off so easily, it was not properly torqued on there, the flywheels usually don't pop off like that either. You really should use the proper OMC puller tool. Not torquing the nut sufficiently could cause the flywheel to shift on the tapers and shear the key, then you will lose spark. The tapers will be damaged also. Over torquing the nut will cause the flywheel tapers to spread, then the flywheel will never stay in place. I'm not saying we all haven't "cheated" at this operation before, but it is important to realize what can happen if the flywheel is improperly torqued. Makes a mess out of the crank and flywheel tapers, shears the key as well.
I think I know what happened. The teflon tape you had on the gas hose threads got into the valve and stopped up the works. Never put teflon tape on welder gas threads.
Yeahhh I didn’t think of that! I put that on there years ago before I figured out the magic behind those fittings.
Great job on the video. I've long been a fan of the Grasshopper mower but not an owner of one yet. Keep up the good work. It did look like the alternator bracket was not what I would call robust from the factory.
Thank you sir! We’ve run grasshopper for years on our large properties. I recommend getting a diesel they seem to last the longest!
Tell your friend to clean the water ways out get replacement impeller check, clean/replace the thermostat, clean the carb put a new set of plugs in, put some new oil in the gearbox. That'll make it more reliable. He may wish to adjust the trim as it stern is too low in the water
I just read your comment to him. He’s actually sitting in the truck with me right now! Thank you for the advice we’ll be doing all of that in a couple weeks.
Very interesting video. I have a near match to that motor and just finished rebuilding my carb to get her ready for this 2022 season in Ontario. It's satisfying to fix something like that and almost as satisfying as watching a video of someone fixing something like that. I have had mercury 25s as well as the Evinrude and our Evinrude 25 is the most reliable one yet. Thanks for showing us the trick for getting at the points. I've not had to do that on mine yet. Your buyer is going to be very happy with that boat and motor combination for a long time!
Hey thanks for the feedback man! I loved that evinrude always loyal. I had good luck with mercury as well. They just don’t make outboards like they used to.
Great video. You need to get some gloves with the impact on those blades. Keep that up and you'll have to change the name to 9 finger shed lol.