Video

Just made my first end grain cutting board and made the same mistake. Thank god for the internet

Nice easy design. Not too complicated.

You weren’t kidding when you said minimum tools lol. Great job bud.

Nice and simple, I like it.

is there a reason NOT to drill dog holes on the whole top? im brand new to this so really loved your video thanks!

Just made my own in school, took lots of inspiration from you

You need 3 more to rap around the deck

Drip caps go on top of the ledger board to protect water from get ting in behind of the ledger board! Putting it at the bottom does absolutely nothing for routing water away from the ledger board! DRIPCAP!!! Please fyi guys don't do this.

Do you find that this size router table is sufficient for most woodworking? I was considering making one like this where it would be turned sideways so the wood feeds onto the work bench. Might use it as a jointer. I'm debating to make one either exactly like yours, like yours but sideways, or integrated into the work bench itself. What do you think? Thanks.

Do you have the cut list?

Unfortunately a wood worker that probably isn't a birder. A beautiful design, but... painting or staining can be toxic to chicks, always place a predator block over the access hole, make 3-4 shallow kerf cuts below the access hole both inside and out the inside cuts allow chicks to climb when the fledge, inadequate ventilation means eggs and chicks can over heat, a wood roof would offer more heat protection. Obviously a very nice project but not safe for eggs or chicks. Sorry.

Too much of your face instead of video of what you was talking about.

I like covered deck how much does it cost

Hi is your header board resting on 2x4's in the wall or just nailed to the outside sheathing ?

That’s awesome!!

Beautiful!

good information

Hey who do you get your wooden chairs from? I have been looking for those everywhere

there is truly nothing new under the sun. I made something very similar to this about three months ago and thought how clever I was for coming up with something new, only to find out it has been done already. Your build has a couple of nice features I omitted. What you might want to add to yours is a couple of dowels corresponding with your dog holes, that way you just pop the jig in place. Second, for the fence I just used a wide board, routed two slots and put two fixed bolts through the table itself, the slots being in the fence instead of the table might make easier to slide.

Do you have a link for the tablecloths you use?

Hows the porch holding up?

Thanks for your idea. Just what I was looking for.

Great table! You can put some dog hole size dowels in some 2x2 pieces that act as a movable shelf to rest wood on for your vertical side.

Lose the music or mix it lower. Otherwise good video

i quit using pay pal they hold my funds for 21 days. there excuse is i don't sell a lot of stuff

Great work!! 👍 what kind of rope did you use?

Thanks for all your tips!!

You can a little pock glue to your scare to block the holes... if you screw it in the center... you it as a axle and rotate 45 degree to paint the missing lines

Cute.

Safety first on the rip cut huh?

I want to make this with no more tools than a drill. I was thinking of getting the ply wood cut the right dimensions at Home Depot, but would there be a way I could work around the brad nailer? Thank You:)

The roof is awesome. outstanding birdhouse.

Skip the music. Not needed. Great tip and vid otherwise

Nice work❤

Nice one!

I kind of like it bouncing back.

I absolutely LOVE your bowls

how many gramars

I find it comical that he has a massive tractor to do the digging, but still mixes his concrete by hand 😂😂

Amazing work! Where did you get the sound module? I didn't see the link in the description. Thanks.

If the router won't reach your slab, what do you do? Raise the slab some how or lower the router some how?

عندي ورشه نظارات هند ميد حابه اتعرف علي حد يسوقها شغل هند ميد 100/100

great video, thanks so much!

Great Video! How far are your posts spaced? Are they 6x6?

Nice set up. Where can I get the black table covers?

What was the Total Cost of your materials?

Very nice work Drew. would you please share where you got the speaker and fight song from.

I notice in one of the comments, you respond that your birdhouse is more for decoration than for functionality. Glad you recognize this, as a tin roof, which has great rustic appeal, will, in hot summer months, broil the chicks inside. Also, cleanout was mentioned, which is a valid point. Likewise, ventilation holes must be provided for a viable abode for birds. Otherwise, good building technique ...

What do you use to glue the layers of wood?

Salaam brother thanks so much love you films Allah bless good big Allah ❤❤❤❤❤❤❤❤❤❤❤❤❤❤