Analysis of Beam with UDL by ansys Mechanical APDL.

Analysis of beam with UDL & point load by ANSYS MECHANICAL APDL 16.0.SFD & BMD of beam with UDL & point load by ANSYS MECHANICAL APDL 16.0 Analysis of Beam with point load & UDL solved by using Mechanical APDL 16.0. In this video u can learn how to draw the give beam with given different loading conditions. How to find SFD & BMD diagram, reactions forces ,displacement ,stress, animation of deformation & many more results . Created by PANKAJ KUMAR.Plz like , subscribe & share with your friends.
~-~~-~~~-~~-~
Please watch: "Channel bell icon introduction"
• Channel bell icon in...
~-~~-~~~-~~-~

[@sophies674]

Thank you a lot, best tutorial

[@trishreddy9814]

now in this problem, the length of each element is divided into 30 sections but what commands should be used to divide the length of each element into sections of equal length throughout the beam.

[@imdadimmu8741]

Thanks 👍

[@mastervenom5167]

Dude u are too good😍😍😍!!!

[@Pankajstudytechnical]

thanks dude 😍

[@freemanfreed1581]

I have no cross sectional area information than the moment of inertia . How do I model it in ANSYS?

[@kallolpatra2874]

How to add ' elastic Foundation (by using series of spring) support ' of a beam @ can you guide me sir..

[@rushikeshwaje]

Thanks a lot buddy

[@luongvinh965]

Why the ETABLE command is ignores when i type SMISC,3

[@samiullahdar6287]

detailing of reinforcement

[@kaushikakabari]

can you explain me more about Element table (3,6,16,19?) how can i get to know about these numbers? please give me little explaination. thanks in advance

[@Pankajstudytechnical]

It can't be explained in few sentences in comment box better u should learn SFD AND BMD analysis chapter of CAD/CAM book

[@kaushikakabari]

@@Pankajstudytechnical i know what sfd and bmd mean ! i meant with numbers only ! how can i find element table ! i got result only for displacement! if i use DOF function for von missese stress for example it shows me a result same as a result for displacement vector sum!

[@christructural]

go to ansys help windows and look up for the element beam188, then look for table 188.2, you'll see items and sequence numbers

[@amoghmangalam3130]

Good one . Why we have taken SMIC 1 , SMIC 3 , SMIC 19.... ??

[@Pankajstudytechnical]

Please go CAD CAM book ..it is about node selection for particular parameters calculation..

[@ashwingowda4485]

i am getting etable error what to do?

[@thanoonmahmoud5924]

Thank you for this vedio
I want to simulate concrete column wrapped with CFRP with ANSYS finite element ...can you please provide me with a reference or video could help.
I'm looking forward to hearing from you soon.

[@jawadkaram7841]

hello, can you make a video for composite ( as example 4 layer ) under buckling with any support, thanks

[@gurrapupavankiran6917]

sir is it possible to do the same problem for solid model which was imported to ansys

[@Pargesparrow]

Yes, use workbech instead of APDL

[@sachinjain890]

I don't have plot result option there, how to do then?

[@narayananr2377]

Hi, when I try to add Element Table, following error is displayed "The requested Database is not available. The ETABLE command is ignored."
I am a beginner to ANSYS, Can you help me with this error ?

[@trishreddy9814]

I got the same error. Do we need to install any packages for this?

[@Pankajstudytechnical]

Yes..I think u have not installed your software properly..or I haven't have crack .

[@luongvinh965]

Did you solve it bro??

[@Pankajstudytechnical]

Sorry I can't help u brother..in this regard.

[@trishreddy9814]

what units does ansys consider?

[@Pankajstudytechnical]

for length -mm unit

[@trishreddy9814]

And what about force

[@Pankajstudytechnical]

N-mm

[@richardlowrence919]

Hi trish can u help me in making model on ansys

[@viroedits]

kya yrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrr.

[@nishant7546]

What does LOAD KEY 2 means? Why didn't we took 1?

[@zoren1994]

Point load of 500N is LOAD KEY 1

[@aatiryounes1765]

I want to simulate a rectangular coil with surface 2mm * 10mm and with 53 turns at high frequencies, the goal is to simulate ski effect. Could you please help me

[@ashishkshirsagar9870]

Can you please explain each thing properly......and you are doing things very fast.......each time we have to seek the video back to understand.

[@Pankajstudytechnical]

Play the videos @ 0.75x speed

[@santhoshsp1501]

How to get software

[@Pankajstudytechnical]

Bro u can contact your faculty if u r a college student.else Google it.

[@ajaikrishnaramalingam7646]

how did u give the cross section of beam it was not given in the question

[@Pankajstudytechnical]

ajai krishna .. because I have to 200×300 mm beam ...u can input according to your requirement

[@ajaikrishnaramalingam7646]

Mech. Engineering Knowledge Junction so if nothing is given then we can assume is there any procedure to assume the values why particularly 200 x 300

[@Pankajstudytechnical]

ajai krishna ...I consider this dimensions as per my requirement . There is no fixed rule u design according to your requirement

[@rohankumar2098]

I'm getting value for Fz also how do i avoid that?

[@Pankajstudytechnical]

It's default c/s..but u can whatever u want

[@mohammadshahnawaz4894]

Audio quality is not good. Do something about it in upcoming videos.

[@Pankajstudytechnical]

Ok

[@m.n.3558]

@@Pankajstudytechnical I thought it sounded pretty good :)