Would this be recommended for creating cornering lamps on a vehicle? Once a standard on Lincolns & Cadillacs, (activated by the turn indicator, to remain on a few seconds after turn indicator stops)
Hope you can help! The wiring on my car is damaged and will cost more than it's worth to fix. So what I was going to do was connect to a power source that turns on with the key, then connect to a start button, and then to the starter relay. I was thinking after the sixty seconds the starter could not be engaged by accident. so I was wondering what the power output was or if it was passive. I have already ordered it but still two weeks before it arrives so i am mapping out all the safety switches I need so that is why I was wonder about the power output. Thank you
I have my cars underglow wired into my cars DRL as it's the only source that will allow the cars underglow to turn on when I unlock the car , I'm looking for some sort of switch that when turned on will start a countdown to turn off , ie the 12v ignition turns on the countdown timer and turns off when it's counted down
So if put a push button switch to turn the relay on it will be like a key cycle and will charge the item im controling for the amount of time i have it set for .. well how about if i put a momentary switch if i hold the switch longer that the program time will it stay on or turn off the relay just make sure . I using it for a hydraulic clutch launch control silonoide. Just want to make sure it full disengage just incase he mess up and hold the momentary switch during the track run
I am trying to make a DIY lightsaber. The two spools will hold the blade material, and when the button is pressed, or switch flipped the motor will spin and push the blades out. Can I use this to make sure the motor only spins for a second, on enough for the blades to come out but no further spinning of the motor? Also, can this somehow work with a DC motor? I'm not sure what's optimal to drive this system, as it will be chain driven, or gear driven, with bidirectional capabilities in order to retract.
What type of relay do i need to make (Follow Me Home Headlights) i need a relay which will receive the signal from the door being locked/unlocked and can stay on for about 10 seconds which can signal the headlights relay switch to turn the headlights on
Question: Can this relay be latched back with power to the contact using the open contact that when energized with a trigger will maintain the circuit with 12V. The trigger itself may be pulsating but once stops pulsating the trigger and the latch will continue until the timer is done and drop off the power and whatever else I'm powering with 12V?
Hey, can you guys recommend a delay relay board module Basically I have a TV that powers on goes in to standby (manually have to press the power button to wake/turn in the TV) I'm looking for a relay onces turned on Waits off for say 5-10 seconds Momentarily on for a second 1/2 seconds to simulate button being pressed - Turning the TV on & Then remains off till power cycled 👍 Hope this makes sense
I am looking for a timer that has the time adjustment to start the light to go on but to be able to adjust amount of time for light to stay on and then go off.
hey and thank for th vedio I want to ask you where can I find (off delay timer 12v in the market) the counter start to count when I cut the power? I mean i want it delay off..12 volt with relay when i press power the light turn on and it countinus lighting until I cut power off then the light turn off after 5second
@@QMVFastTech, many thanks, but I've now bought some infinite loop relays, and they're all working well. I appreciate your help and the link too. All the best!
Are you trying to add another minute to the existing minute? You adjust the potentiometer to adjust the time, if you wanted to add an additional minute you would need to double the discharge resistor value on the timer.
Would this be recommended for creating cornering lamps on a vehicle? Once a standard on Lincolns & Cadillacs, (activated by the turn indicator, to remain on a few seconds after turn indicator stops)
Hope you can help! The wiring on my car is damaged and will cost more than it's worth to fix. So what I was going to do was connect to a power source that turns on with the key, then connect to a start button, and then to the starter relay. I was thinking after the sixty seconds the starter could not be engaged by accident. so I was wondering what the power output was or if it was passive. I have already ordered it but still two weeks before it arrives so i am mapping out all the safety switches I need so that is why I was wonder about the power output.
Thank you
so could i have a simgle wire on the output that would heat up on startup to burn some polesterine
I’m looking to disconnect the negative wire of a cb speaker for 3seconds after I unkey. Will this work? Does it send voltage out of the relay?
H ey Danny Iam locking for a circuit diagram for the Timerprint QF1021A/B V1.5a thanks Hermann
I have my cars underglow wired into my cars DRL as it's the only source that will allow the cars underglow to turn on when I unlock the car , I'm looking for some sort of switch that when turned on will start a countdown to turn off , ie the 12v ignition turns on the countdown timer and turns off when it's counted down
Will this unit be able to be used fr a turn signals on a home made trike that I'm wiring up
So if put a push button switch to turn the relay on it will be like a key cycle and will charge the item im controling for the amount of time i have it set for .. well how about if i put a momentary switch if i hold the switch longer that the program time will it stay on or turn off the relay just make sure . I using it for a hydraulic clutch launch control silonoide. Just want to make sure it full disengage just incase he mess up and hold the momentary switch during the track run
Hi, can this be used to delay the dome light of a car? and will it turn off if the key is turned to ignition?
I am trying to make a DIY lightsaber.
The two spools will hold the blade material, and when the button is pressed, or switch flipped the motor will spin and push the blades out.
Can I use this to make sure the motor only spins for a second, on enough for the blades to come out but no further spinning of the motor?
Also, can this somehow work with a DC motor? I'm not sure what's optimal to drive this system, as it will be chain driven, or gear driven, with bidirectional capabilities in order to retract.
What type of relay do i need to make (Follow Me Home Headlights) i need a relay which will receive the signal from the door being locked/unlocked and can stay on for about 10 seconds which can signal the headlights relay switch to turn the headlights on
Question: Can this relay be latched back with power to the contact using the open contact that when energized with a trigger will maintain the circuit with 12V. The trigger itself may be pulsating but once stops pulsating the trigger and the latch will continue until the timer is done and drop off the power and whatever else I'm powering with 12V?
Hi is this compatible with use of a 12v fuel priming system
I need one that can go off after 15 minutes.
Can I set this module to 15 minutes?
Hey, can you guys recommend a delay relay board module
Basically I have a TV that powers on goes in to standby (manually have to press the power button to wake/turn in the TV)
I'm looking for a relay onces turned on
Waits off for say 5-10 seconds
Momentarily on for a second 1/2 seconds to simulate button being pressed - Turning the TV on &
Then remains off till power cycled 👍
Hope this makes sense
Im also looking same module. Have you found it or figure it out? I only found a 555 module in monostable mode
I am looking for a timer that has the time adjustment to start the light to go on but to be able to adjust amount of time for light to stay on and then go off.
Here is a relay that will work for you: www.qualitymobilevideo.com%2Fbu509td.html
hey and thank for th vedio
I want to ask you where can I find (off delay timer 12v in the market) the counter start to count when I cut the power?
I mean i want it delay off..12 volt with relay
when i press power the light turn on and it countinus lighting until I cut power off then the light turn off after 5second
Here is a timer that will do that: www.qualitymobilevideo.com/bu509td.html You will leave the power connected and once release the timer delays.
Hi,is it possible program this timer 0,3 seconden ?
Hi, is their an online instruction sheet on how to programme this relay, including loop function? If so, could you send me a link to it please?
This is not capable of looping. This unit is capable of looping: www.qualitymobilevideo.com/tdr12v4.html
@@QMVFastTech, many thanks, but I've now bought some infinite loop relays, and they're all working well. I appreciate your help and the link too. All the best!
Can I use only one second one suddenly off?
I want this product
Can this be used to turn off "Check Engine" or "Airbag" light after 60 seconds?
No, this is not meant for that.
220v motion sensor and N555 module, DIAGRAM
Need one withTime delay off
is there a time delay off??
Can i use 9volts?? for timer swicth
Yed
How much
Mereko 5 nomodyul chahiye kitne ru mileg
How to increase the delay for one minute
Are you trying to add another minute to the existing minute? You adjust the potentiometer to adjust the time, if you wanted to add an additional minute you would need to double the discharge resistor value on the timer.