How To Install Dishwasher For Beginners | DIY Dishwasher Installation (Step By Step Guide)

Sdílet
Vložit
  • čas přidán 8. 07. 2024
  • How to install dishwasher for beginners might seem daunting, but this DIY dishwasher installation step by step guide along with the right tools will enable you to do it yourself. Here's a beginner-friendly guide to help you through the process.
    Tools and Materials You’ll Need:
    New dishwasher
    Adjustable wrench
    Screwdriver (Phillips and flat-head)
    Tape measure
    Level
    Power drill
    Wire nuts
    Teflon tape
    Dishwasher installation kit (including water supply line and power cord if not included with dishwasher)
    Bucket or towels
    Step-by-Step Guide:
    1. Prepare the Area
    Turn Off the Power and Water: Locate the circuit breaker for your kitchen and turn off the power to the dishwasher. Shut off the water supply under the sink.
    Remove the Old Dishwasher (if necessary): Disconnect the power, water supply line, and drain hose. Remove the screws securing the dishwasher to the countertop and carefully slide it out.
    2. Measure the Space
    Measure the width, height, and depth of the opening to ensure your new dishwasher fits properly.
    3. Attach the Power Cord
    Locate the Junction Box: Usually found at the bottom front of the dishwasher.
    Connect the Power Cord: Attach the wires from the power cord to the junction box using wire nuts. Match the colors: black to black (hot), white to white (neutral), and green to green or bare copper (ground).
    4. Connect the Water Supply Line
    Attach the 90-Degree Fitting: Screw the 90-degree elbow fitting onto the dishwasher’s water inlet valve, using Teflon tape on the threads to prevent leaks.
    Connect the Water Supply Line: Attach the flexible water supply line to the 90-degree fitting, again using Teflon tape.
    5. Install the Drain Hose
    Connect to the Dishwasher: Attach one end of the drain hose to the dishwasher’s drain outlet.
    Secure the Hose: Use a clamp to secure the hose in place.
    Route the Hose: Run the hose to the sink drain or garbage disposal. Secure it using a clamp.
    6. Position the Dishwasher
    Carefully slide the dishwasher into the opening. Use caution to avoid crimping or pinching the water supply line and drain hose.
    Level the Dishwasher: Adjust the leveling feet at the bottom of the dishwasher so it sits evenly. Use a level to ensure it’s not tilted.
    7. Secure the Dishwasher
    Attach to the Countertop: Use screws to secure the dishwasher to the underside of the countertop. This prevents it from tipping forward when the door is open.
    8. Connect to Power and Water
    Turn on the Power: Flip the circuit breaker back on.
    Turn on the Water Supply: Open the shutoff valve under the sink to supply water to the dishwasher.
    9. Test the Dishwasher
    Run a Test Cycle: Turn on the dishwasher and run a short cycle to check for leaks and ensure everything is functioning properly.
    Check for Leaks: Look around the connections for any signs of water leakage. Tighten connections if necessary.
    10. Final Touches
    Secure the Kick Plate: Once you’re sure there are no leaks and everything is working properly, attach the kick plate at the bottom of the dishwasher.
    Clean Up: Ensure the area around the dishwasher is clean and free of tools or debris.
    Tips for Success:
    Read the Manual: Refer to the manufacturer’s instructions specific to your dishwasher model.
    Ask for Help: If you’re unsure about any steps, consider asking a friend for help or consulting a professional.
    Be Patient: Take your time to ensure all connections are secure to avoid leaks and other issues.
    By following these steps, you should be able to install your dishwasher successfully. Enjoy your new appliance!
    00:00 Introduction
    00:44 Turn off Water Supply
    01:28 Disconnect dishwasher hoses
    02:33 Remove dishwasher mounting screws
    03:47 New dishwasher unboxing
    04:19 Disassemble bottom of dishwasher to connect new hoses
    04:58 John Realizes he is missing a hose and a electrical cord
    06:01 Water supply hose install
    07:40 Drain hose install
    09:08 Electrical Power cord install
    10:05 Reassemble the bottom of dishwasher
    11:00 Install new mounting brackets
    12:13 Connect new hoses and plug in dishwasher
  • Jak na to + styl

Komentáře • 7

  • @ricosreport
    @ricosreport Před měsícem +1

    This is a great tutorial! Thank you for the step by step installation instructions!

  • @ADBorrego
    @ADBorrego Před měsícem +1

    "It was at this moment that I realized that I fucked up." Lol ... Keep making these videos, and I'm gonna keep watching!