EASY DEWALT CHUCK REPLACEMENT WITH NO SET SCREW.
Vložit
- čas přidán 26. 08. 2021
- In this video I show how to remove a drill chuck from the DeWalt DCD797. I wanted to make this video after trying to find a solution to my broken chuck. I looked all over and found nothing that could help me. The most common diy removal method is to remove the chuck's set screw (or not) depending on the model, inserting a large allen wrench into the chuck, hand tight, set the drill in lowest gear, set drill to drill mode, lay on side and hit the allen key with a hammer counter clockwise to remove the chuck. I did try this method however after banging on the allen for about 20 mins I decided to just remove the chuck. I got the idea from a youtube video of someone disassembling a dewalt drill. In the video the shaft that holds the chuck just slides right out of the gear housing. I thought why not just remove the chuck in the same manor however instead of breaking down the drill just pull the chuck straight out...and it worked!
DCD791/796 compact drill and hammer drill, and the DCD991/996 3-speed drill and hammer drill.
This is a link to the chuck shown in that video
www.amazon.com/dp/B00DD7KUXO?...
Keyless Drill Chuck Extra80-RV13 Röhm 1328310 for Milwaukee, DeWalt and Makita, 1/2"-20" Mount, 1/16"-1/2" Capacity with Retaining Ring, Trough-Hole, Metal
May work with DC901KL DCD995M2 DCD995B DCD985M2
DCD985B DCD970KL DCD795D2 DCD785C2 DCD959KX DCD950KX DCD950B DCD775KL DCD775B DC725KA DCD930KX DCD990M2 DCD980M2 DCD940KX DCD960KL DCD790D2 DCD790B DCD780C2 DCD780B DCD760KL DCD760B DC720KA DCD920KX DC730KA DCD710S2 DCD910KX DC7DCF895M2 DCF895D2 DCF895B DCF886M242KA DC750KA DCF886D2 DCF886B DCF885M2 DCF885C2
DCF885B DC827KL DC825KA DC825B DC835KA DCF815S2 DC845KA
DC800KL DCF889M2 DCF889B DCF889HM2 DCF059KL DW059K-2 DW059B DW059HK-2 DC821KA DC821B DCF880M2 DCF880B
DCF880HM2 DCF883M2 DCF883B DC233KL DCH253M2 DCH253B
DC212KL DC212KA DC212B DCD771 DCD777 DCD778 DCD780 DCD785
DCD708 DCD709 DCD791 DCD796 DCD991 DCD996 DCD998
Repair to a DeWALT DCD 771 1/2inch Cordless Drill Driver that chuck continues to loosen when used resulting in drill bit loosening and falling out. Ordered online a replacement chuck after a few attempts to remedy the chuck not holding tightly. Drill chucks are critical to the operation of the tool and ours is bent all out of whack so we're going to replace it! However, in order to do that we'll have to get the old chuck off of the tool and that ends up being a bit of a difficult operation. Lets see what we can do! The drill is a Dewalt DCD771 20v Max cordless model, and the new chuck is a Dewalt The keyless chuck Is jammed on my cordless drill. This video will show you how to release a jammed Chuck on any cordless drill with a keyless Chuck.My drill bit got stuck in the chuck, this is just a quick video on how I fixed the keyless chuck on my dewalt drill. If you have a chuck that has jammed then this video may be useful.
This was way better than sending in for repair and the hassle of not having your drill for a period . After using this method I have had no problems with the chuck since. Worth a try but don't hit that chuck too hard. If a slight tap doesn't free up the chuck then there may be another problem there and the drill may have to go for repair. How to Use a Drill/Driver, Impact Driver, & Hammer Drill and How They're DifferentLearn how to use a drill/driver, impact driver, and hammer drill. DCD777 / DCD796 / DCD996: Chucks how not to take them off
This is a hot new take on completely ruining a drill. NEW DeWALT XR It's not a 976 because that's a myth How to remove chuck on cordless drill. Easy way to open a jammed chuck and get stuck drill bit out
How to REMOVE and REPLACE a chuck on a Dewalt DCD791, dcd796, dcd777 and dcd996 cordless drill , make without center screw. Reemplazar el portabrocas Dewalt dcd791. Dewalt DCD791. Chuck, easy replace, «no center screw» Do I fully strip down your Dewalt DCD996 I go into full detail showing how to tear the Dewalt 18v battery drill, showing which screws to remove and even which stickers to remove for a clean strip down. The video also details the safe removal and fitting of a new replacement chuck for the Dewalt 18v DCD996 drill on how to remove the drive spindle from the chuck and also how to remove the chuck from the gearbox. This particular drill chuck is specific to DeWALT manufactured brands, including DeWALT and Porter-Cable. If your cordless hammer drill is showing any of these symptoms; replacing the keyless chuck could solve your problem: 1) Drill bits slipping or falling out of chuck 2) Chuck won’t open or close 3) Chuck jaws (teeth) damaged 4) Chuck seized onto spindle 5) Chuck is difficult to rotate Get model-specific repair help from eReplacementParts.com. Learn how to troubleshoot, diagnose and repair your power tools and equipment with illustrated instructions, hundreds of step-by-step repair videos, and our DIY forum. - Jak na to + styl
There's nothing more annoying than having to hand-screw something together czcams.com/users/postUgkx1McjgiqTNcTjrhvRvJWcrk5bzTeQW-Wn except for the pain in your wrist that is. This addition to my tool kit is great and I can get a lot done without all the pain and annoyance. The battery last's a long time and I have yet to run out of power when doing a small project (granted I am saying small project because I'm no construction worker). The only thing that I wish it had was an LED or pair of LEDs to indicate when it was charging and whether or not the charge was complete (or full).
Absolute perfect and easy to follow video. Just saved me from buying a new drill. Did it in ten mins. I couldn’t insert the Allan key as the chuck was totally broken and would not hold anything. I held it as tight as possible in a vice and cracked open the shaft with a spanner. Hey presto it came off easily. Thank you for uploading 🫡
Hello I'm from Brazil, it was very easy to remove the chuck with your explanations, thanks for sharing your knowledge. The model I exchanged was the DCD 796.
Ok, this is looks doable. You gave a huge favor to DeWalt. In think they are too ignorant or arrogant to admit that this kind of design held back a lot of people to buying these "screwed" models. By watching your method i might change my mind and buy one of these.
I was a little sceptical about the prising off the Chuck but low and behold it came off fairly easily and I got the shaft unscrewed as pictured there are more complicated
ways shown on ytube but yours is by far the quickest I’m just waiting for a replacement Chuck to arrive now. You have saved me from getting a new drill. Thanks
Nice work! Thanks for watching!
I had a chuck that was screwed from day one. This worked even smoother than your video shown. Thanks for the video.
I'm glad you found this video helpful. Thanks for watching!
Thanks so much - like the other folks I had exactly same problem with my DeWalt DCD795. You method worked a treat and have saved me an expensive repair or a new one - there's nothing wrong with the drill itself, thank you Sir. Great video.
Thanks for watching!
David Kelly iv got the dcd795 also. Iv got a bit stuck in chuck and chuck is stripped. Jw its will wrk the same way with out 795 as shown in this video?? And a question for both of you guys, can ether of you give me a link to the chuck i need th purchase? Agin iv got the 795. Thanks fellas
@@rickyrickharris4908 Hi Ricky sorry for delay. So I'm in the UK and I managed to get this De Walt DT7012-QZ chuck which has worked brilliantly and was super easy to install onto my drill. it's a lot heavier than the original chuck so it kinda behaves like it's in hammer mode most of time, even drilling timber but it's fine. Works great - hope this helps
I used my DCD 980 to mix thinset and sure enough chuck froze up so need to replace it, i watched countless videos on how to replace and hope this works. Going to get the same chuck you used, this exactly why i come to You Tube even with the annoying commercials! Thanks
GENIUS thank you i managed to remove one today using this method
Best video ever , followed instructions and worked perfectly, had to wet sand the shaft and light machine oil to reinsert for spring to reseat
Thank you sir… perfect instructional video.. been frustrated with my DCD791 for way too long.. did just as you instructed ( had to add some Blaster to loosen it up was getting nowhere ) and wham she came right off… Thank you once again… can’t thank you enough 👍
I'm glad you found this video helpful. Thanks for watching!
Wish I found this video prior to dismantling my DCD797 to attempt to replace the chuck. Didn't go so well to say the least. LOL. Ended up upgrading to the DCD805. At least I have the Rohm chuck still as a spare.
Amigo ha encontrado el santo grial para el reemplazo de ese mandril , gracias por su video👏👏👏
Works a treat 👍
Had to use a bit of heat to get mine to come undone but saved me hours of stripping that drill down good as new now
Excellent video I haven't seen this method of removing it before. I have repair videos on CZcams too.
I have never tried one of these chuck repairs before. Liked and subscribed well done my man.
Worked a treat !
Saw the full dismantle videos before I found this and didn’t fancy trying that.
Hoped this would work for me and it did, Not only that it was easier than I thought it would be, Thanks
I'm glad you found this video helpful. Thank you for your comment and thank you for watching!
Saved my Bacon. worked well for me despite having what I thought was no pin. the pin head snapped off allowing me to change the chuck. I am happy with that!
You are an absolute star. Just done it with mine. Like a new drill now. Thank you.
Thanks for watching!
Was able to just do this with the 791 ! This model has the chuck more sunken in so the outside is a little damaged after i was done. But since there was a small drill bit actually stuck in my chuck I think this was my only option. Thanks for this video!
I'm glad you found this video helpful. Thanks for watching!
Best video I seen on this drill. This method works great. I was done in under 10 mins. Thx for the upload!
I'm glad you found this video helpful. Thanks for watching!
Me too, Thank for this video , I did exactly as shown and the chuck came away very easily. Great job
Thanks for watching!
Although I was sceptical this method worked extremely well for me the chuck prised off very easily without any damage to the surrounding housing -maybe I was lucky for once-. The method for removing the chuck from the spindle also worked well I used an old Vileda mop metal handle cut in half for extra leverage on the allen key and Spanner which I thought would split due to the thinness of the tubular steel used in its construction but didn't. Excellent Instructions thank you very much.
Thanks for watching!
Thank you! It worked! will be buying the new chuck as advised! Thanks again!
This is THE BEST technique, BY FAR!!!
Thanks for the advice
Unfortunatly I bought a rubish dewalt DCD 796.
it will be the third chuck in three years
Looks easy. Will try it when new part arrives.
Thank you so much. Your explanation together with the demonstration have proved invaluable. 6:51
I'm glad you found this video helpful. Thanks for watching!
Thank for this video , I did exactly as shown and the chuck came away very easily. Great job
I'm glad you found this video helpful. Thanks for watching!
@@DoItWithDave thank you Dave for posting a useful video , there are so many on you tube that have no idea really what they are doing but just stumble along , but yours was very sensible and informative. Thank you
Excellent video, just done mine now 👍
Nice! Thanks for watching!
perfect! fast and easy thanks!
Thank you I just changed my one and it’s works great
I love your channel name.
I just subscribed, by the way.
You saved me!!! tnks a Lot!
Thanks! This was pretty easy.
Thanks for watching!
Gr8 and easy way. Thanks
Thank you great video
Great video, the best method I've seen. He recently purchased the DeWalt DCD800, which came with the chuck with some annoying movement. This model has the same problem, it does not have a fixing screw. Will the Rohm chuck you used work on the dcd800? Thank you so much. Greetings!
Thanks for the info. I ran into an issue reassembling though where the drill was stuck in hammer mode. Turns out the bearing and gear under than metal cap with 3 screws are press fitted to the shaft, so you have to press them back on otherwise it’ll just hammer.
I have the same problem, and took the three screws and plates off, but I can't see how to press it back in, I've tapped it with a hammer gently, To no avail
How do you press it back?
Fabuloso gracias amigo eres grandioso
Amazing trick
Buenas tardes amigo tengo un taladro dewalt mod dcd 7781 se puede quitar el portabrocas higual como ese que tu se lo quitaste espero tu tespuesta y gracias por compartir tus videos muy claros y bien explicados y me gusto tu video y tenga su like gracias
Hello, your video is brilliant, I have followed the steps, I have used your method because I couldn't remove the t20 torx screw inside, I just want to know what should I do as next step on putting everything back together regarding I have the t20 screw. My drill is DCD795. Any advice please?
Also the torx screw bit when removing actually snapped off the little bit. Do I actually need this part for my drill when I'm going to put together
Currently trying to figure out chuck removal on a DWD520, it appears to have no set screw and freely spins so hitting an allan key is pointless. I wonder if it will pull out too?
You could give it a shot. Maybe pry up a bit and see if it starts to pull up without having to use too much force. No set screw I'd think it'd be the same set up. There's always a complete disassemble and reassemble process. I hope this helps.
Thanks 😊
Some people replacement chuck is all open to change
Gracias🇺🇾
I couldn't see the part number on that Rohm chuck to look it up. What is it so I can order one? Thanks.
There's an Amazon link to it and the part number in the description.
I did this to my drill just to test it to see if I could get it out as you did, I did get it out quite easily, but when I put it back it only operates on hammer whatever setting that you put it on, can't understand this any ideas
I ran into that issue a bit later after doing this. I used a c-clap placed on top of the chuck and on the back of the drill (ferring strip on housing) to seat the double D fitting. I hope this helps. Thanks for watching!
Mine just gave up a week out of warranty really annoyed. Used adjustables a few times and now my chuck is distorted.
Helo, of de Argentina, sory for my english. In my dewalt dcd 985 the chuck broken but it is closed. I dont see screw in. Do you know if it has screw, to remove only lever, (minute 2/3.Thanks you so much
So based on the blown out images it looks like it does have a set screw. The link below will show it. Look at 21.
www.ereplacementparts.com/dewalt-dcd985m2-type-20v-hammerdrill-parts-c-1009_9661_566974.html
I hope this helps.
thank!! 21
Do you think it could work also on 996 model?! Great video!!
If you don't have a set screw it may. If you do try this definitely don't force it. It should come up slowly but surely. I hope this helps.
Did you ever try this? I have TWO DCD996 with bad chucks. Contemplating trying this vs complete disassembly.
Is your drill newer than mine, mine is dcd795
Not sure. Got mine in 2017 as part of a package deal.
What is the purpose for the big bolt looking at the tip of chuck for??
I think you're referring to the "Set Screw". It's used to hold the chuck in place.
@@DoItWithDave lol, I know what set screw is.. I’m sorry. What I mean at the near of chuck tip it look like 3/4 nut … assume it just a style??
@@timjones6637 if you're referring to the new Chuck in the video I believe it can be used to loosen and tighten the chuck to the shaft instead of using an Allen key?
@@DoItWithDave i think so too.
Got the chuck but since chuck won't tighten at all I may have to replace the shaft as well
Idk if you've tried tapping the teeth in the chuck and spinning it a bit to try to get them to tighten. It may be possible to get a big pair of channel locks to hold the bottom of the chuck while you untighten the shaft.
Ive got a bit stuck in mine and used channel locks to losen chuck well it started spining alright but bit didn't loosen at all now iv got a free spinning chuck with a bit stuck in it lol. So at least i can get the chhuck off ill find a way to loosen it once its off
So I noticed that the chuck just came out with prying so I used a large vice grip pliers to grip the chuck and I waked the pliers with a Mallet, gave it 10 good hits and it flew off. Took me literally 1 minute.
Good show! Thanks for comment. I helps the community greatly.
@@DoItWithDave also the front of the chuck has a hex bolt that you can put a 5/8 size socket on and really grip it well with a ratchet. So you don’t have to use a Allen key, mine was stuck open so there was no way for me to put an Allen anyways. But a crescent wrench and a 5/6 socket made quick work of it.
is this the same for a DCD740? mine is also in without a screw, but I don't have the fuel 360 degrees of prying like yours. it's the right angle drill
On Amazon, in the review section of the dcd740, there's a response to someone asking if the chuck is removable and they said yes. Idk if that means Allen key and Hammer or not. I also read in an online forum that someone disassembled the housing to remove the Chuck for the 740. So I'd think it would come. Less pry area like you said. It may be possible to spin the chuck as it's being lifted up to get it on all sides. If you decide to try this and see the chuck is obviously able to be pulled away from the housing (gap between back of chuck and drill housing) it's probably a go. I hope this helps.
@@DoItWithDave Hey, I've tried both methods to no avail. I tried prying, and I tried turning the chuck with an hex key both ways. It would make sense to be a normal LH thread but it wouldn't come off. There's a hex inside. I need to use the damn thing.The chuck is stuck open
Has anyone tried this on a dcb999
The other fault with these exact drills is they get stuck on hammer action the internals on these are so cheap nowadays.
I know it's pretty frustrating. Silver lining I got a 7 piece kit with hard box on wheels for $499 around 4 years ago and it paid for itself many times over. Thanks for watching.
Mine is stuck on hammer mode now lol
Watch this video, it shows what you need to do to fix hammer only mode.
czcams.com/video/eo2GGE9GLLI/video.html
So is mine
@@MrLonstar I appreciate it
Actually after looking at most of the videos here on CZcams regarding removal of chuck on these DCD drills, your doing it wrong, the way your doing it, it removes the stem which you do not want to remove, it’s done exactly the same way as they chucks with the set screw, if no set screw just simply tighten with a large Allen wrench and hit with a hammer, once loose just unscrew and screw on new chuck
Why don't you want to remove the stem?
@@DoItWithDave if your only replacing the chuck, the. Chuck is the only thing that should be separated from the drill itself and when your buying a replacement chuck you will only get a chuck, no stem, so basically your doing more work than needed. Peace
@@johnjkizer6399 okay I understand now. Simply removing the chuck with Allen key and hammer is definitely the best way to go about it. I my case I literally spent an hour using the preferred method to no resolve. Even tried a heat gun. I only showed it this way because of that and was hoping to help anyone else that was having the same issue. Thanks for your post. More information definitely helps anyone trying to replace their drill chuck.
muy mal montaje del chuck, golpeando se daña el taladro