It's a mystery. These kinda calls can drive you crazy. Especially if you did everything right and you have an angry jerk for a boss that doesn't realize that in the real world stuff happens.
Joe another way to test schrader is put a cap on it with a hole in the cap then use leak detector to check at the hole in the cap if you get a hit then use bubbles to verify on the cap when putting bubbles in the end of the service port you take a chance of contaminating the refrigeration system when you attach you gauges. Just a tech tip from a nobody to a super tech.
Self contained 2 door freezer Re-Builds - Take A LOt of time & Have to be done 110% Correctly. otherwise they WILL bite u in the but / be a Headache. if it's over 10 years old replace condenser fan motors & Suction pressure regulator. Suction pressure regulators leak by the adjustable screw. 10 years on motors is it. toss em. a tip for you - Use 55% Silver & Flux when welding in compressors. it will look alot nicer , lower temperature. Compressors are steel. You are basically welding steel to copper. treat the welding as such. if u want to continue using 15% on your compressor installs , dip your 15% Rod in " Stay silv White Brazing Flux " it will help u alot. Your Welds were dirty. That's why it looks like they did not go so well. Clean up the outside of the compressor joint. clean the inside with a clean rag or paper towel to remove any oil. Clean copper is Very important on hot gas welds & suction on hermetics. Clean the outside of the joint when the plug is still in it with a little sand cloth. Compressors & driers should be welded in with 45 or 55% silver rod c & Flux or a Orange 🍊 rod 55% pre Fluxed rod. a Good Looking Weld is A Good Sealing weld = no Pinholes. If a weld looks Shitty You can Cover it in White brazing Flux , Re-Heat it / Get it Real hot & the flux will do the rest. it will let the good stuff flow in & Float out the dirt. i'll do some Videos.
@@restaurantrepairs i did forget The Most important one thing - ALLWAYS , always, always , REPLACE THE " Line set Loop of copper - the Suction line gets Pin holes in it !!! Super important on Freezers & ice cream dipping cabinets !!! Ever since i started doing that - it got rid of so many headaches !!! Best thing i ever started doing !!!
Good call 👍👍👍
Awesome video brother.. keep up the good work.
Line set loop,or evap,tan tan tan.
It's a mystery. These kinda calls can drive you crazy. Especially if you did everything right and you have an angry jerk for a boss that doesn't realize that in the real world stuff happens.
Well you did good for warranty.
💪👍❄️🇺🇸 good call good job
Nice call. Things happen. 👍
Styx (the angry young man)
Joe another way to test schrader is put a cap on it with a hole in the cap then use leak detector to check at the hole in the cap if you get a hit then use bubbles to verify on the cap when putting bubbles in the end of the service port you take a chance of contaminating the refrigeration system when you attach you gauges. Just a tech tip from a nobody to a super tech.
I hope the super tech gets your message. 😂. Brilliant idea with the hole in a cap. Definitely gonna drill one out now.
Nice Trick Man !!! i'm gonna use that !
As will I. Great idea.
I'm not saying it _wasn't_ a leaky Schrader. I'm just saying that every time *I* have a leaky one is on a Friday.
I Hate that more than anything cuz I never believe that was all it was
@@restaurantrepairs Me either.
Self contained 2 door freezer Re-Builds - Take A LOt of time & Have to be done 110% Correctly. otherwise they WILL bite u in the but / be a Headache. if it's over 10 years old replace condenser fan motors & Suction pressure regulator.
Suction pressure regulators leak by the adjustable screw. 10 years on motors is it. toss em.
a tip for you - Use 55% Silver & Flux when welding in compressors. it will look alot nicer , lower temperature. Compressors are steel. You are basically welding steel to copper. treat the welding as such.
if u want to continue using 15% on your compressor installs , dip your 15% Rod in " Stay silv White Brazing Flux " it will help u alot. Your Welds were dirty. That's why it looks like they did not go so well. Clean up the outside of the compressor joint. clean the inside with a clean rag or paper towel to remove any oil. Clean copper is Very important on hot gas welds & suction on hermetics.
Clean the outside of the joint when the plug is still in it with a little sand cloth.
Compressors & driers should be welded in with 45 or 55% silver rod c & Flux or a Orange 🍊 rod 55% pre Fluxed rod.
a Good Looking Weld is A Good Sealing weld = no Pinholes. If a weld looks Shitty You can Cover it in White brazing Flux , Re-Heat it / Get it Real hot & the flux will do the rest. it will let the good stuff flow in & Float out the dirt. i'll do some Videos.
👍
@@restaurantrepairs i did forget The Most important one thing - ALLWAYS , always, always , REPLACE THE " Line set Loop of copper - the Suction line gets Pin holes in it !!!
Super important on Freezers & ice cream dipping cabinets !!! Ever since i started doing that - it got rid of so many headaches !!! Best thing i ever started doing !!!