I WOULD DO THIS DIFFERENT NOW JUST REPACK THE BEARINGS WITH GOOD GREASE AND PUT SEALS BACK ON.
Vložit
- čas přidán 25. 07. 2020
- Please read the comments before you change your bearings if i would do this again i think i would just repack the top bearing and put the seal back on and maybe still take the seal off the bottom bearing.
✅My Amazon store. www.amazon.com/shop/diyjim
✅grease gun amzn.to/3hCZdBk
✅grease high temp amzn.to/3jQxSxF
✅impact wrench amzn.to/2BxsGx5
✅impact sockets amzn.to/3hFPkmy
✅bagger kit (42 in.) amzn.to/2DTQooJ
My T-shirts diy-jim.creator-spring.com
5% off shirts use DIYJim2021 when checking out
DIY wooden ramps • Ultimate DIY wooden ramps
how to change oil • John Deere 100 series ...
how to level your deck • How to LEVEL your mowe...
grease and sharpen blades • John Deere 100 series ...
Thank you very much for watching and God bless
*Full transparency. I am a participant in the Amazon Services LLC Associates program, an affiliate advertising program designed to provide a means for me to earn fees by linking to Amazon.com and affiliated sites.
*Disclaimer - Thank you for visiting my CZcams channel. Please understand that the content on the DIY jim CZcams channel is intended for informational purposes only. I make no warranties about the completeness, reliability and accuracy of this information. Any action you take upon the information posted on my CZcams channel is strictly at your own risk, and I will not be liable for any losses and damages in connection with the use of my CZcams channel.
#johndeeredeckbearings #johndeerebladespindle #bladespindlebearings - Jak na to + styl
I am 77 yo, I started my apprenticeship on April 1 firs1959 in Germany and I am still learning to this day. To install the upper bearing use a pipe that is a hair smaller than the outer race never hit on the inner race because you will ruin the bearing at installation, also grease bearings before installing.
Thanks for your comment sir hope your holidays are good.
I was being Born in 1959, then I too went to Germany in 1976. alot of good Memeoies over there.
If you are replacing them its easier to use old bearings to pop them in.
Curtis, I was in Germany in 1976 in the Army. We are the same age. Might have met in Germany. Where were you stationed?@@curtismoore6387
I was a mechanic for 40+year! I can see from a lot of misguided information you folks are confused about what constitutes a sealed bearing and a caped bearing… A lawnmower Spindle bearing is capped not sealed! Don’t believe find a sealed bearing and try and remove the the seal without damaging it! NOT GOING TO HAPPEN! You will tear it up getting it out! Now a caped bearing on the hand has a removable cap like the ones demo on other videos! They call them sealed! WRONG. Fill that spindle enough to get pressure and you’ll see grease! If it were sealed you’d blow the bearings out and still not get grease to penetrate. Please Google the definitions of a sealed bearing opposed to a capped bearings! I’ve got a 21 year JD145 and I’m overhauling the deck for the first time! I’ve always greased the three spindles. Never been replaced. I rest my case😅
Many years ago I went to the SKF Bearing Maintenance Training. I highly recommend it. Some takeaways: (1) The bearings in this video are 2 type. Double sealed, as seen in the bearing with the black seals . And the bottom bearing is a combo seal and metal shield. The metal shield offers better protection with all that debris being churned up during cutting. (2) Sealed bearings are factory filled to 20% capacity with grease. (3) Shielded bearings create less heat from friction than their sealed cousins. Now, the number one reason for mower spindle bearing failure is that the grease gets used up. We've all pulled out spindle bearings and found them bone dry. Yes, the zerk fitting is to pump grease into the spindle cavity to prevent the shaft from freezing to the shaft spacer. It's a waste to fill the cavity just to grease the shaft/spacer. I use anti-seize. But if you could keep grease in your mower bearings they will probably last until the deck rusts away. Once a year I use a needle greaser to add grease. 360 hours/12 years and still going. The bearings are 6204-2RS. 2RS= double sealed. Cheers.
very good info thank you for commenting
The anti seize goes on the 2 bolts on each blade that hold blade to bearing shaft ..they tend to grow on
Very good info! There's a lot to bearing engineering and lube. Two other reasons the spindles are packed with "life Time grease: Manually, greasing can inject dirt and other debris through the grease fitting. And replacing spindles is easier and yields more profit for mechanics and dealerships than changing bearings. LOL
@@czellner5894 The often heard term "lifetime grease" is a misnomer. No bearing lasts a lifetime without adding grease at some point. Yes, replacing spindle assemblies is easier, but I make more profit by replacing the bearings. I don't buy the ebay Chinese spindles because the lack of quality will come back to bite me in the arse. So I purchase quality bearings in bulk, and can swap them out faster than ordering spindles and waiting.
My original bearings lasted 16 years, mowing 2.5 acres. I bought eBay made in india spindles with sealed bearings. How long do you think they will last without removing the dust covers and greasing them?
a grease gun puts out 10 000 psi. them covers will not stop it , thats what they are loose fitting dust covers , not seals , pump grease until you see it come out ends of spindles it will go threw bearing like the covers are not even there , thats how they are designed to work , no need to remove bearings to remove covers , it will take 40-50 pumps to fill when new and like 6-8 when maintaining them to purge contaminated grease out and fill berrings with new grease , remember every time you remove them berrings the soft aluminum spindle. gets egged out a bit and before you know it you will have a spun bearing and your spindles will be junk , you will then have to peen the bearing in and use some loc tight bearing retainer
Thanks for the info and thanks for watching
Thank you. This is what I've been confirming over the past few days after receiving my Cub Cadet Ultima ZT1. Planning to update them with a zerk fitting so I can properly grease and maintain them for years.
Thanks! The only thing I would do differently would be to pack bearings by hand and fill the cavity with grease while I could. That way it would not take very many strokes with grease gun to keep the bearings full when doing regular maintenance.
Thanks for watching
Hey Jim, I have a lot of respect and admiration towards you. I love the fact that your intention is to share knowledge. However, when someone comments that your input might be wrong, you humbly thanks that person and advices all viewers to read all comments. You are a good man! Keep up the good work. God bless you!
Thanks for watching Lucas
I said something to my local John Deere dealer about these bearings being sealed and he was not happy. To bad. He said I hate social media. I said I don't, This is how I find out things they don't want me to know. Now I service my own mower.
Thanks for commenting have a good summer
Im having a dealership issue as well, they want to sell me the entire (3 of them) spindles instead of just bearings, not the first time theyve tried to screw me around, just have to bypass them to get what I need.
If you want to financially survive, then everyone should learn how to service their own equipment. Now to contradict myself, I've made some nice side money servicing my neighbors small engines.
@@manandatractor
That’s not not a contradiction - you’re providing a service and your time and skill aren’t free.
Thank you so much for this instructive video! I purchased a JD 345 with a 42" deck 2 seasons ago, and need to pull the deck prior to the first mowing this spring .... I'm def going to service the bearings prior to reinstalling. I've been a JD owner for decades, and never knew till recently that "sealed bearings" couid even be serviced! I've learned thru you and others that they can! I'm wondering how many bearings over the years I could've saved by simply tearing into them!! Thanks again. P.S. it's refreshing to hear a guy put a video together without putting up with the foul language!! You are obviously a man with some moral ethics .... KUDOS, and thnx again!
Thanks and thanks for watching
The zero fitting is there to grease the grease the inside of the spindle house to keep WATER OUT. As a mechanic for over 45 years I replace spindle housings all the time in mower decks from damage and water. Many when you grease them you can see it push the water put past the bearings. Sealed bearings will run for years if you keep the water out. And NEVER WASH A HOT MOWER DECK.
Thanks for the advice have a good summer
Makes you wonder about that wash port. First thing I took off.
@@joehead1294 I use my wash port on my 50" Toro ZTR. BUT I also drilled and tapped my spindles, and they got pumped full of grease after I finished using the wash port a few times a season. No room for moisture with spindles oozing grease from both sides.
Mechanic for 45 years and never learned that the grease is for the bearings. That’s a tragedy. Pump till
They are full and grease gets into
The bearings too then they last more than a few years they will last forever then you don’t need to replace them and go into the unit. Water being pushed out is a benefit but not the purpose of the zerks. Good grief. I’m not even 45 years old and I figured that much out.
I’m happy you are showing how to make them last 10 plus years and keep them greased
Thanks for watching
Pack the bearing before reinstall.
thanks
No you don't have to , take the inside seals off and after you put everything back together just grease it til the grease starts to come out that means the grease has gone all the through the bearings just a cleaner way of doing it ! And use a plastic hammer !!
I not only pack the bearing but I also manually fill the spindle as well. Grease cartridges are expensive and there is so much space that you can use up an entire cartridge before you get enough grease in there to even reach the bearings.
I don't have that problem. Here in the PA Pocono mountains we grow nothing but many sizes of rocks. Each winter they grow. I brake spindle mounts before the grease wears out.
Thanks for watching take it easy on the rocks
40 minutes in to owning a brand new Deere my deck decided to go in to self destruction mode after i hit a stump. Deck, blades and spindles all busted...
It's amazing how they work themselves to the top
@@langora5804 holy crap that sucks
@@grandwaha If i want to dig a hole for a plant I feel like I am digging in a gravel pit. You can't stand on the shovel as it only goes down an inch or so. Enjoy the spring!
Thanks for your videos... I just greased we’ll attempted to grease mine yesterday...guess I’ll need to do this change to make it really stick. Thanks again keep the vids rolling God bless as well
Glad you like my videos thank you for watching and leaving a comment it helps my channel. Also i always have links below my videos if you use them that also helps support my channel it does not matter what you buy, does not have to be what is in the link. Just trying to let everyone know since my wife is quitting her job to stay home and homeschool our boys.
Great Video Jim! You talked+ walked through step by step - A+! TKS MUCH! DON!
Thanks
Hello Jim. I have to change the bearings in my Shivvers Country Clipper zero turn about every 4 years. I have tried putting the new ones in with the seals intact, and also with the inner seals removed so that new grease reaches the bearing cage. There doesn't seem to be much difference in overall longevity either way. I will recommend that if you choose to keep the seals intact, you should not "over grease" the spindles, as the grease pressure will push the inner seals into the ball cage and the bearing will soon be toast. This will happen even if the spindle is equipped with pressure relief vents. They don't open until the pressure reaches 5 psi, which is still too much force for the seal to not be damaged. A very good video. You do a great service to the home DIY guys. Thanks for sharing.
Thank you very much for the well explained comment I hope this helps someone.
Great point about pressures within the spindle. Sealed bearings are used to help keep the grease inside the spindle. Removing one side will put all the load on the outer seal and likely cause its failure. Also, the average spindle generates enough heat to somewhat 'liquify' lithium grease. If it's properly maintained, pressure will seep some of that liquidy grease into the sealed bearings.
Man, I am new to the channel and wanted to thank you for the video on the deck adjustment. I just bought a John Deere LA 105, needed some adjustment. Thanks for showing how to do it the right way.
Glad I could help
I got the La 115 purchased 2008 300 hours.
Very informative show of displaying full pully pulling , checking pulls bearing n greasing n reinstallation with a good video. Thanks buddy.
your welcome Thanks for watching 👍
Thank you so much, I may have to watch this several times to get the total concept, but that's ok. Appreciate
Your welcome, thank you for leaving a comment
I have several things that run that style bearing and most aren’t where I can use a zerk fitting to help in any way. I usually pull the bearings out every so often and pop at least one if not both seals out and repack the bearing then replace the seals and reinstall. Sometimes it’s a royal pain to do it but it has drastically reduced the number of bearings I’ve had to replace.
That is a real good thing to do to help bearings last, thanks for commenting have a great summer
I was waiting for you to pack the bearing with grease before ya installed them back in
That would be a good idea
Definitely should pack the bearings before reinstalling, your not giving the bearings a good head start, ALWAYS pack your bearings.
Good Job
What do you think the pressure from the grease gun is going to do when he fills the cavity? No sense in doing extra work if it will just happen later.
Great video man thx. Many people grease the fitting on the spindle and don't realize the bearing is sealed and gets no grease.
Thank you
Very good video on explaining on how most bearings have seals on both ends.
Thanks for watching
Very good video. I learned a lot. Thank you for sharing your knowledge with guys like me that aren't very mechanically monded. We need a lt of help Brother! God Bless your channel. May it prosper and grow as your spirit grows.
Thank you very much
My John Deere spindle bearings are: 1. top bearing sealed, 2. bottom bearing open on the side that is facing into the grease area, and the bottom of it is sealed. I can understand why they did it this way. A. If the top bearing is open on the side facing the grease, there's a chance that, when the bearing warms up, the grease will gradually drain out of it and cause it to run dry. A sealed top bearing is far more reliable than an open one, B. Having the bottom bearing open on the side facing the grease area, can be filled with the grease when a grease gun is used to fill the cavity. Leaving the bottom side seal intact prevents the grease from running out and it seals the bearing from moisture and debris.
The truth is, most homeowners never bother to grease these spindles, just run them until they fail. Nowadays, a generic replacement spindle is about $25 (2021 price), so it's not such a big expense to just replace the entire spindle assembly when the old one fails and starts making noise. And, it's a good time to clean the spindle mounting area on the deck and spray a little paint on it to help prevent rust.
Thanks for commenting and watching my video hope your having a good summer
I appreciate the video, gives me something to think about when I check out the spendal towers on my John Deere mower! God bless and keep you safe!👍
Thank you very much. God bless you also
I am so glad I found your site... Your videos are so well explained... I just finished making the ramps following your video. Without it forget it... Also I’m brand new to John Deere and again I’ve learned so much from your videos... it’s my first ever lawn tractor... my wife bought it for me cause I’ve had two back surgeries and I can’t walk to good... Anyway Jim, thanks so much and god bless my friend... you have a fan for life... Raymond...
that is awesome glad you like my channel i try very hard to make my videos easy to understand. God bless you and your family also.
Also i always have links below my videos if you use them that also helps support my channel it does not matter what you buy, does not have to be what is in the link. Just trying to let everyone know since my wife is quitting her job to stay home and homeschool our boys.
DIY with JIM oh wow Jim, I’ll be taking a look at those links...
I've been working on centrifugal pumps for many years, nothing kills a ball bearing quicker than over greasing.
Thanks for the info and thanks for watching
Same goes for superchargers, and high volume air pumps. We're conditioned to the way we used to pack old Timken spindle bearings on a car. But SKF will tell you 20% fill is what a sealed bearing needs. More equals excessive heat= bearing failure.
So the spindles are set up the same as a motorbike wheel hub. Love understanding how things work :)
Thanks for watching
Great video man! Gonna do what you said about taking the top of the bearing off. You do a great step by step procedure-taking nothing for granted.
Make sure you read some of the other comments a lot disagree if you have around a 1/2 acre i really think the bearing will last for a long time no matter what you do. Thanks for watching have a good summer
The whole purpose of the sealed bearings is to keep the grease in and the water out, when the grease is gone, or they get water in them and fail, its time for new bearings. They likely just put the grease fitting there to appease those who felt they needed to grease the spindles. The bearings in my spindles are original from 1995 and still going strong. I pulled them out and repacked them about 8 years ago with some synthetic grease when I repainted the deck.
Thanks for watching and commenting
Purchased my simplicity 25 years ago ,been greasing spindles once a season since ,never had problems ,never apart !
Thanks for commenting and watching my video
Yeah me too remove all dusk covers refill until you see clean grease. Never replaced spindles in years.
You’ll never begin to get that with simply leaving those sealed bearings as they are. Whatever they pretend is grease today in those sealed bearings is so thin it’s nearly invisible.
@@drizler That’s why I removed all the seals & grease them every couple hours.
Thanks for the info and insight. Your details really help!
welcome
Here I Sit At 3:00 AM Unable To Sleep Because I Have Things On My Mind And Then I Watch This Video About The Bearings In Mower Deck Needing To Be Greased. Just Something Else For Me To Worry About. Thank You For An Informative Video.
I just redid everything on the mower deck. On the D125. After ten years of beating the crap out of it. I never even greased anything ever. only changed the motor oil. What I found was the two spindle pulleys the 7" dia ones were starting to strip out their centers.The spindles had like 1/16 play on the shaft . I replaced both spindles, and both pulleys neither of those pulleys had much wear in them, and deck belt, I've replaced the deck belt like three times now.I must have put six sets of blades on this D125. Rocks are hell on blades. I just replace the drive belt for the first time. I also had to straighten out the mower deck, ,as I had bent it int so much the blades hit it. Yes I truley beat this thing up. My thought is simple, I won't touch those bearings at all. I think If you grease the spindle the force of a grease gun wii force grease into those bearings. If nothing else the grease in those bearings can't go out either.The spindle cavity if full of grease and pressurized bye the grease gun. Maybe it works past those seals? Bottom line I'm not going to disassemble those spindles. I'll replace the entire unit, if it gets play into them.
Wow sounds like my mower will last forever my lawn is not very hard on it. Thanks for watching
What I really want is solid rubber tires for a D125. Ones that can never go flat. Everything in Arizona has thorns, big thorns. I'm tired of flat tires. I air up this D125 every time I use it.
Sounds like a pain in the butt. Thanks for watching
brilliantly explanatory video ! thank you
Thanks for watching
John Deere isn't the only company that made this mistake. I just changed the center spindle on my 7117 Simplicity with the very same issues. An oldie but still going strong!
thanks for the comment
I'm glad I saw this video ty,I will be doing the same on my John deere
Glad I could help
Alternately, you can schmoosh grease into the bearings themselves and the put the cover back on. It's more work compared to leaving them off and using a grease gun in the future, but it helps keep them clean and from getting sand or other particles in them over the years
Also, at least for the top bearing that has a removable cover that is outward facing, you don't have to completely remove them like you did - just remove the cover, push in some grease, and put the cover back in. Gotta love applying the knowledge I gained skateboarding to fixing tractors 😉
Thanks for the tip, thanks for watching
I did this to my '66 cub cadet deck idler pulley. Everyone thought I was nuts. That was 20+ years ago, and it's still mowing.
Thanks for watching
Jeff Webb Perfect answer from another man that spent many years with bearings always wet ,water soaked.
Thanks for watching
Just fixed my jd 165x thanks for the help.
3 beers for you..😁😁😁
Glad it helped thanks for commenting
Great job on the video. Instead of fill that void with grease I pop my bearings out, take off the seals, clean and repack the bearings. Then I put the seals back on. At the first sign of wear I replace the bearings. Regular price at Princess Auto is $4.99 and they go on sale for 1/2 price. 6203-2RS & 6204-2RS. Take Hans Nielsen advice for installing the bearing. Thanks for your time on making this video.
Awesome thanks for the info, thanks for sharing
Which one is it? 6203 or 6204?
@@lkevonly One of each. One is for the top and the other is for the bottom.
Its not just John deer.
My cub cadit didnt have the tube inside and the inside of thd grease chamber was as large as yours
Without pumping 4oz or a full tube of grease into both or all three spindels your berring could never get greased. Me i hand packed them full took off all the pullies and hand packed the berrings.
See 3 winters ago i took off the deck to fit the snow blower on then wShed the deck and put it away for winter figuring it would dry out.
Well it was dry the next spring but so were the berrings they made all kinds of niose loud very loud.
Thats when i took it all apart and added a high temp high speed grease after running with the PTO on for a few min it got quite agine
Sure the berrings got some dammage but i didnt run it very long just a few min, so it was only some rust wd49 fixed that.
No problems after 3 summer seasons. And i did take the dust caps off thd berrings you pump more grease in untill it pushes some out both sides. Thd ideler pullies have to be done by hand each one new is about 35 bucks.
And you cant replace the berrings its welded togather john deers are rivited thoses you can dril out the rivits and put short bolts and nuts in. Look on youtube somone shows how. Why would you spend 50 bucks to replace a 2 dollar berring
Thanks for the tips and thanks for watching
My grease fitting is on top of shaft so I dont think my Craftsman has that metal tube inside spindle but I can see how it would help force grease into bearings that way, if there wasn't any seals. Good info thanks for posting!!!
thanks for watching
The metal tube between bearings is needed to squeeze bearing races so balls inside bearings spin instead of housings spinning
depends on the particular bearing about the seal....the easily removed plastic seals are not really good seals and some grease/oil will pass through. Then there are the bearings with metal seals, they tend to seal better but also will allow some passage of oils from the grease. I have a John Deere mower bought new in 1997, it has the exact same set up for the mower deck you are showing here. The bearing type is metal seal, I know because today I took one spindle apart so I could get bearing size to order new ones. I have always pumped grease as regular service and just now I am getting some bearing play on one spindle. This mower has seen several thousand hours of mowing, heavy mowing for a lot of it. When I replace the bearings I am going to remove the seal on the inside face of the bearings, that will allow grease into the bearing. I will not drill a weep hole, I want to assure that pressured grease reaches into both bearings, even if the remaining outer seal ruptures. I regularly grease the spindles anyway so the bearings would be flushed often if and when a seal gives way to grease pressure. I have been doing that kind of modification for bearings on all kinds of machinery since the 1960's and it works superbly.
Thank you watching and for the explanation
Another excellent video. Another step could be to pack the bearings by hand then reinstall. Sort of belt and suspenders.
thanks for watching
Thank you for the video. Blessings to you.
Your welcome Gail
You still need to drill a pressure relief hole in the spindle housing opposite the grease fitting to let out the pressure when greasing the spindles. As soon as the relief hole starts squirting grease the spindle is full and your ready to go. If you do not have a relief hole in the spindle housing you run the risk of blowing out the other seal on your bearing do to excessive pressure on it without a relief hole. Make the relief hole 1/16" in size to 1/8".
Thanks for the tip and thanks for watching
There is pressure relief fitting that can be installed like a second zerk. It is like a backward zerk in that with enouh pressure the spindle contents are released. My Ventrac mower decks have these. The "rubber" seals will allow grease to pass by them inward to ball bearings and cage.
I had to replace my bearings and spindles. I pumped them so full of grease that it was hydraulically pushing against the bearings and housing. So now I take out both seals on the bottom and the inside of the top. Also, if you go to an industrial bearing supply, you can get a stronger bearing for just a few dollars more. A bearing designed to last years in a factory will last you for a decade.
Thanks for the advice
I have a 6 ft. mowing deck by Landpride. Last summer I replaced all the spindles, pulleys as one big unit, and I believe I have three or four of those spindle units that wore out. To think the bearings are sealed when you have a grease fitting to shoot grease in is a joke on us. So greasing doesn't do a thing because the seal shields it. But even taking the seal off doesn't do much either because grease follows gravity down and can never reach upwards and stay there to feed the bearings. If I were you, I would have greased the bearings by hand, then reinstalled them, and not expect the grease to revitalize those bearings when you pull the trigger.. It''s the same as doing a automotive brake job. When the bearings are good, clean them up, and repack the bearings with a glob of grease in the palm of your hand, and slap the bearings into that glob to force all the grease it can take. I'm not sure if removing the plastic cover resolves the problem of the bearings finally getting all the grease it needs. So then what is the purpose of designing zerk grease fittings into a lawn mower that does no good. It gives you a peace of mind when you decide to buy the mowing deck, until you get to that ah-hah moment years later when you realize it didn't matter. It's a marketing ploy and a design flaw.
I agree I think now this would be a better way thank you for the comment
I only got 130 hrs on my 1st set of John Deere spindles on my X300. By the time the bearing went it chewed up the spindle casing below making the blade wobble. The 2nd set I greased about 60 pumps until grease was visible on the blade side. A CZcams channel showed someone testing the theory whether grease gets into a sealed bearing and it does. Proven with a different colour grease. Hopefully my new spindles last longer this time. If this pair goes on me then the next set I will take apart and hand grease them 1st and after that, once a yr at the zerk fitting.
Thanks for watching hope your new spindles last
Excellent video! I just had one of my spindles ware out after 150 hours. I'll replace both and remove the seals in both and hope I do better than 150 hours. Thanks !
Welcome, thanks for watching
Very well explained & videoed Thanks.
Thanks glad I could help
You did good job on the video Sir, after a few years of messing with bearing I will give one piece of advise.Always press or tap the bearing in place by the outer race.When you tap on the inner it can damage the balls and cause it to over heat and jam up.Learned the hard way and burt a belt up.
Thanks for the tip and thanks for watching
Thanks! Very helpful & thorough...
welcome
Good show!
Thanks for commenting
Nice video thanks for the help.
Your welcome have a great summer
I think the grease would have by passed the rubber shield IF the spindle had been injected with enough grease to fill it and pressurize it. Works for me. Fill'r up!
Thanks for watching
I think it would follow the path of least resistance, so would the grease not go out the spindle gap before going through the bearing cover since it’s a tighter gap.
Bought a John Deere S130 last fall, so starting to get into maintaining it. Recently greased the front wheel hubs, steering spindles and front axle pivot and was undecided on whether or not to grease the blade spindles. I watched a few videos on the subject along with this one and found the videos and the comments to be very interesting.
At first, it made sense not to grease the spindles since the bearings are sealed, figuring to add bearing grease as necessary down the road. The argument for no spindle greasing was supported by the fact that some spindles have no grease zerks at all.
Then, some suggest (like your video) to remove the inside covers on the bearings to allow periodic packing of the bearings by filling the spindles. Initially, I gave consideration to this idea until I investigated a little further. One reason against this was the possibility of gravity pulling the grease out of the top bearing. Another was the possibility of popping the outside bearing covers off due to the pressure of overfilling the spindles. Right or wrong, I figured this procedure might add to the possibility of moisture and debris contamination of the bearings, especially if drilling weep holes in the spindle to avoid over pressurizing.
So back to thinking not to add grease until I read that keeping grease in the spindle keeps moisture out, avoiding any rusting of the shaft and spacer. Also, reading that the intent of adding grease to the spindle is to keep the friction down thus lowering the operating temperature.
Decision made right! Not so fast. I was under the impression that my new John Deere S130 no doubtably had zerks on the spindles, right? WRONG, hadn’t noticed before now, but NO, there are no blade spindle zerks on my 2021 S130. (See updated reply)
Guess you don’t have to worry about grease. Thanks for watching hope you have a good summer.
Yes, you too. I enjoy watching your videos.
Updated reply
Saw yet another video where someone had to replace an old John Deere spindle. The new spindle has the grease zerk on the top of the shaft (I assume there is a small hole in the shaft inside the spindle to allow the grease to flow into the spindle). Lo and behold, that’s where the zerks are located on my S130. Would’ve been helpful for my manual to show this zerk location, but it describes the zerk location on the side of the spindle.
The manual says to grease the spindles every 25 hours with one or two shots of grease. So I have settled on keeping it lubricated per the manual.
Also very interesting, the latest video that I watched also showed the old John Deere spindle that was being replaced having the bottom bearing without a seal on the top. The top bearing had both sides sealed. Looks like even the manufacturers struggle with what is the best method of extending spindle bearing life (or is it all about the bottom line - cost).
I saw a YT video that showed the grease gets pumped thru the bearing past the seals, and comes out the other side. Bearing were sealed on both sides, and he showed a inside of the bearing before and after pumping, and the new different color grease came thru. Don't recall the link, but the seals flex enough to let grease get pumped past them. And the seals did not pop off and stay out of place. Was surprising.
Thanks for watching
The way the guy at the bearing supply explained to me : metal shield are designed so metal shield does not contact metal race so grease may flow past. Plastic , rubber whatever is designed for a contact seal. . So following that ,if you want to be able to re-grease maybe for bottom bearing put metal down (to "vent" and remove upper seal of that bearing. My limited experience is the top bearing can last a long time (25 year old DR field and brush mower, still good factory top bearing) so, seems like leaving top as sealed is OK. I am going to leave both mine as sealed
thanks for watching and thanks for the info
Great information, thank you
Thanks for watching
Great vid.
Thank you
That’s crazy that jd designers did it like that I have one that is over 20 years old. I will definitely do this to it. Thanks
Nearly all mower spindle are that way, not just JD.
agree
Thanks for sharing.
You bet
Very well done Thanks
thanks for watching
I've been modifying these bearings and spindle housings for years. Yes the bearings do get grease and the decks rust away before the bearings fail. If you're afraid do do something you won't accomplish anything.
Thanks for watching my video and commenting
Grease passes through on my Hustler. The aftermarket spindles didn't have zerk fittings so I drilled and tapped them. Took a ton of grease but it did begin to push around the dust covers. Mine look like your bearing with the black rings. I can't call them sealed because mine are just some kind of fibrous dust cover.
What I will do on my other mower is grease them real good with a grease needle using red-n-tacky grease. Needles are 3 for $6 at Amzn. Reusable of course.
Thanks!
Thanks for watching
I appreciate the video. I would leave the sealed bearings sealed .I'd like to see if the greased unsealed bearings actually last longer
I'm going to see how long they last because I am not taking apart again until they wear out, thanks for watching
I think we're going to need some put brand new spindles on there mower do one spindle removing seals and the other leave stock and do same maintenance to both and see How they last? Hopefully someone down South that mows year round to get results sooner!
Wait how about greasing the brgs again then take it apart to see if grease gets to the brgs. The sleeve looks like it covers the center race that would stop the grease from the brgs? Seems like there should be a drilled hole in the sleeve to fill the spindle with grease packing the brgs?
I watched a video of another guy who demonstrated how the grease DOES get in the bearings if you pump enough in there because it penetrates the rubber seal I also wonder why not pack your bearings with grease when you had them out then reseal ? but I do enjoy your videos of your know how and maitenace so good job keep going
thanks for watching
Nice video - many thanks!
Welcome
awesome job
Thank you
I pull the seals out of the formed pulleys and grease or use sharp needle adapter and stick needle along shaft and seal lip, then add grease while rotating.
Thanks for the tip, sounds like a good idea
If that motor turns 3600 rpm, in an hour long cut the bearings have spun over 200k times. In a season that's many millions.
In the first cutting season of my E140 one of the spindle bearings went out and I didn't notice (headphones on) until it allowed the pully to drop and it ate one of the mounting screws down to the deck. The pieces of the bearing were spread across my yard lol and I greased after every cut but apparently the grease wasn't getting to the bearing. It was a busy summer so I replaced the entire spindle but I'm now changing them and packing the new bearings. Thanks for the video.
Thanks for watching
Well done in every respect!
thank you
Very helpful, thanks.
Your welcome
You could use Timken sealed replacement bearings and not worry about greasing them. That's my plan once mine wear out because I know I'm not going to think about greasing the zerks every year. Good video. Thanks.
replacement bearing are really not to much, I am going to do the same thing.
Thanks for the tip. You gotta wonder if the bearing flaw was a purposeful flaw so you would end up spending more money down the road. Thanks!!!
i have had a few people say they all do it
From a legal perspective it would be foolish beyond imagination to intentionally engineer any part of a machine to fail. 1. There's bound to be much internal deliberation among design staff about employing such a practice. 2. Design flaws spawn recalls 3. recalls spawn class action suits, 4. Class Actions spawn discovery demands for relevant documents, which will unearth above meantioned internal deliberation.
great video. Thanks
You are welcome!
I used to think the same, but completely filling the housing with grease will push grease right past the seals, in one side and out the other on both top and bottom bearings. Try it yourself.
I have changed they way I think about this now that’s why I say to read the comments. Thanks for watching and leaving a comment hope your summer is good
I agree with you 100 percent. If you pump in enough grease, it will actually get past the plastic seals into your bearings. There are videos proving this.
I wonder if the bearings in my 6 year old Simplicity Broadmoor spindles are the same way? Thanks for this, well done!!!
Most likely, thanks for watching
Likely, the spindles in my 14 yr old Ferris were
Grrr8 Job !!! Thx!
Thanks for watching
I've been cleaning and putting new grease in " sealed" bearing forever. Sealed in bearings like these is just a dirt/debris cover. It is by no means permanently sealed. You can silicon the seals edges and this does extend the bearing life usually.
Thanks for watching
Thanks for the update
No problem 👍
@@DIYJIM I like your videos you show everything
@@johnwalters7415 i try not to hide anything except making the video 2 hours long. Glad you like
Good video. Thanks
Welcome thanks for watching
I had a mower deck with sealed bearings with no grease zerk lasted over 20 years. Them bearing are dirt cheap if you know were to by them. I use to buy them in a 10 pack for about 20 dollars if that.
Wow thanks for watching and commenting
My mower is 11 years old, never had trouble, don't send me fishing for trouble !
I think i would leave it alone, than thanks for watching
You know the old saying: 'If it aint broke find something else to make a CZcams video about.'
Thank you brother
Sure thing thanks for watching
That was great thank you
Thanks for watching
Working on cars and trucks must notably on U-joints I found the sealed bearing original equipment last a lot longer than replacements with grease fittings. Your mileage may vary but I believe as long as the sealed bearing is properly greased from the factory it will last longer.
Thanks for commenting and watching my video
Nice job.
Thank you
Its true! A shorter version is to load 90 wt . The top has clean enviornment so rarely give problems. The outside seal catches hell no matter what you do. 90 has less rolling resistance an will keep the seal wet
Added bonus the centrifugal force is just enough to sling off the grit from the shaft rotation. Grease will not fling the grit and more often turns to a wax impregnated Grit going round and round between the shaft and the seal lip
Thanks for watching
My bearings didn't have any inner seals and I'm from Australia though I.ve had to weld the plate where the bearings mount
thanks for watching and commenting
I replaced the open bearings with sealed (metal not plastic) bearings about 500 hours ago. I don't see the need to grease the bearings when a good bearing will last and not need to be greased. I sourced the *Fafnir bearing (about $6 each) and they have been great.
Thanks for the good info and thanks for watching
Great video!
Thank you, like your name
@@DIYJIM Thanks!
What genius engineer designed that!
sell more bearings that way
What genius? One who is trying to make the spindle ass'y last in a very dirty environment. The grease in the sealed bearing is for lubrication. The grease you pump into the zerk is for dirt barrier & purge. The 'genius' as you put it, is the clown who defeats a good system because he doesn't understand the design.
Don't blame the engineer, blame the "bean counter" that told him to do it!!
Good video. I just took the spindles out of my dad’s old Saber JD today because I was getting a little vibration. My dad brought this new in 98 or 99. The spindles had a little movement but I think are salvageable has the original belt and original deck pulleys and still all tight. Any way I ordered all new to replace them and will keep these as a spare. Do you have any information on where I can find replacement bearings for the original spindles? Thanks for any information.
Sorry I do not, leave a comment if you find a good place to buy.
I've been doing this for years in my shop for my customers , but I only do the bottom , never the top because gravity will pull the grease out and have never had a bearing fail by repacking using Lucas Red & Tacky !!
Thanks for the info hope you have a good summer
@@DIYJIM 😉👍
Makes sense. I wouldn't have thought about the gravity aspect. I'll definitely reseal the top bearings.
i agree i think this is a good idea but i am not taking mine apart again
Can't beat that Lucas red and tacky,use it on my truck also. Good stuff,cheap insurance.