An alternative method taught to me by a military armorer that is good on blued parts. Fill a large utility sink or kitchen sink with the hottest water you can stand. A) Cover drain grills or any area that small parts can fall into. B) Add a hefty amount of Dawn dishwashing soap. C) Throw the entire broken down gun into the sink. D) Thoroughly scrub everything. It takes about 3 passes with a bore brush and a barrel brush respectively. Smaller parts anout once with the "toothbrush". E) Ensuring all parts are secure, drain the sink. F) Refill the sink with super hot water and make sure all parts are rinsed. The Dawn breaks down any carbon or oil buildup. The hot water serves two purposes; it helps with the soiling buildup and, this is the biggest point, when you take the pieces out, the high heat helps them dry quicker. Oil everything. While every other unit struggled for hours to pass an armory inspection, we turned our weapons in and were able to walk away to the shock of the armorers. Our weaponswere as clean as if they just came from the manufacturer prior to firing. Still use this method on my AR to this day.
Will it work on polymer frames? I need to clean my tx22 but dont want to do anything to harm it since I hear not to clean polymer with any gun solvent. Say it dries it up over time and cracks.
I started using CLR a few weeks ago after watching one of your other videos. I had horrible accuracy issues with my rifle. After one time my accuracy snapped right back. Thanks for the advice.
Have used CLR for at least 30 years, cleaning house and janitorial work off and on. Great stuff. Would never have thought to scrub a barrel or parts with it. Thank you very much for the idea! You have a new subscriber.
AMAZING, absolutely amazing ! I have a barrel that just wouldn't let go of the icky barrel smeg, and now I'm victories. Ram-rod a tornado brush & CLR, then jag a few times, then repeat. Beautiful results !
I used some CLR I had after seeing your previous video and also ordered the patch-out. Shot the next day and had a .26MOA group with ES 10 and SD 3.6.... thank you sir.... I take what you say to the bank
Agreed. I have been a massive fan of clr for years. Great on stainless, caution with factory coatings. ie pistol slides etc etc, it can take it back to bare steel. Absolutely great on stainless barrels just be sure that's all its on.
Hey Eric, I recently found this page “ like yesterday” and I’ve been following you on Texasbarndominiums but I enjoy this more. Thanks for the vids. Big fan.
Just tried CLR on my 1911 pistol barrels... WOWZA!... best carbon removal I have ever experienced! Thank you Mr. Cortina... absolutely love your educational youtube channel.
I used it on my dad’s Remington 700 30-06 blued. It worked great on the bore but it started to take of the finish off the action. I got scared and took the barreled action out of the stock and rinsed the entire thing with a garden hose.🤣 No major issue on the finish and it shot really well afterwards.
Great work Eric! I try this recently after you mentioned it in a previous post! Amazing how it strips the carbon out, and... best groups yet out of the 338 Edge!
Along the same lines, Zmax engine treatment works wonders on keeping stainless barrels clean. On a clean barrel, saturate the inside and then heat the barrel with a heat gun. While still hot, saturate again, and apply more heat (about 200F). Then just let it cool. Patch out the excess. This penetrates into the barrel and helps prevent the carbon from getting a hold. Works wonders on engine valves, so I tried it on one of my guns. It cleans super easy. Some of the best gun products aren't even marketed as such.
I've heard about using CLR. I was afraid of using it until I was this video. Thanks for sharing. I'm going to give it a try. I have learned the hard way that carbon fouling really sucks!
I would like to thank you for your excellent advice. I am not referring to CLR because I feel that I cannot use it on my blued chrome moly barrel - but rather for advice to use Teslong borescope as a cleaning assessment tool. Based on the borescope it turns out that my normal cleaning regime already removes all the carbon for me - but I found had a big problem with copper fouling. So I did an overnight soak using “Wipe Out” foam which turned all that copper to very dark inky blue liquid residue. It looks great now. Thanks again!
For what it’s worth.. My normal cleaning routine is to start with swab dipped in “Ed’s Red” thru bore guide, let the “Ed’s Red” soak an hour, then 20 strokes with my dewey rod with bronze brush, then push patches soaked in mineral spirits until it comes out clean, then dry patch. Turns out this works great for my carbon but not so much for copper.
‘May all your groups, be one hole.’, for me that’s the classic! It’s old school, I miss it already! Great video, gonna use this added to my cleaning regimen from now on! Thank you!
I tried lemishine and water in an ultrasonic cleaner and was amazed at how well it worked on a stainless muzzle brake. Very fast, zero scrubbing. Cheers!
Lol I’m a mechanic an shoot a ton of long range. I dropped a alternator in that stuff that wasn’t charging over night rinsed it with water put it back on the truck an been driving it for 2 years now haha
Dude! I feel like I need to add you to my Christmas Card list. This works amazing, absolutely amazing! Thanks so much for taking the time to post this. You're the man!
I love your channel. I am not a match shooter and was never in the military. Your content really helps an old varmint hunter like me. Thanks for showing us tips and tricks
I tried it on my brake. It cleaned the crap out of it however it did slightly discolor the polished finish. Few passes across some 1000 grit wet or dry sand paper (wet) and the finish was restored. I found coating the muzzle of my stainless 1911 with a couple coats of One Shot helps stops the carbon tracing. I applied a couple coats to my brake. Haven’t put it to the test yet.
I know this is an older video, but I appreciate the info. I’m gonna give it a try. I recently learned that CLR is great for getting carbon off of exhaust tips so this makes a lot of sense.
Good thing you said to follow with 92% alcohol... Gotta have something to neutralize the acid in the CLR... or you will develop pits in the metal. cheaper the metal, the more likely to pit.
Erik I have a used rifle with a muzzle break much like yours in stainless. Even though the prior owner did pretty good cleaning the barrel I don't think he ever cleaned the muzzle break. I will try CLR as you did but since the muzzle break is welded to the barrel. I will have to hang it over the cup and use CLR like you did. Thanks for the tip!
I have been using CLR to remove carbon from my breaks and barrels without any adverse effects for the past few years good to see someone of Erick Cortina's pedigree else uses it also.
Thanks Erik. New drinking game...every time Erik says carbon...take a drink. Great info lately, keep it going. Would really enjoy some more F-class loading and shooting. Enjoyed the PRS stuff.
Just tried it after getting my Borescope (Teslong Semi Rigid) and that'll explain why my 22-250 lost the handle. Oh my the copper and carbon... Spent a couple hours making it better... Seemed almost copper plated bore was achieved... This system works amazingly well..
I did have some concerns about CLR but I'll give it a try. I've had great luck with a product called "Free All". It's in a spray can so I just give the barrel a shot, soak a couple patches and run them out the barrel.
I ran this through my Bergara HMR Pro's barrel yesterday afternoon. Ran 3 wet patches from breech to bore using a bore guide and let set for about 15 minutes. The 3 wet patches were black as all get out. Patched it out and then used a bore solvent on a patch. Noticed an increase in filth from the wet patch of bore solvent showing that this did a good job. Scrubbed the barrel about 10 passes and patched it dry. Finished with a patch of alcohol and then a few more dry patches. This will now be my cleaning regiment. My break is blued steel, so I quickly wiped it down after the CLR patches inside and out. Probably should have taken it off, but its a pain to time right. Break looks fine after 24 hours too. Thanks man!
When I worked out in the mines I ran out of washing powder, I found "truck wash" in the company store, and as it was free, I figured it would be great to wash my clothes in. The first time I wore my clothes, I became itchy in the nether regions, but it wasn't really a problem. When I got home I realised all the skin on my balls started to peel off and my nuggets were red raw, the funny part was I didnt think it was from the truck wash, so I went and saw the company nurse about it, and it was only then the penny dropped about what had happened.
As you said “major changes before big match”. I think changing from beer to pure alcohol is big. Hehe just joking. Would like to hear more of these. Thanks for sharing.
If you shoot a revolver you know how the carbon builds up around the forcing cone and on the outside of the cylinder and cylinder face. The CLR wipes the cylinder clean with little effort. Unbelievable. Wet a patch and it wipes away.
I didn’t have Evaporust on hand but I did have CLR and used it to remove a little surface rust from an older Stanley needle nose pliers made from boron vanadium steel alloy. Several hours soaking and brass wire brushing did the job.
You could probably have just rinsed the brake off at the tap and gotten most of the carbon off after the CLR soak. We've used it to clean lime from the pans under some bunny cages and rust from plumbing fixtures (city water and the toilet is NASTY!). I think the "demonetizer" was actually showing the barrel of your rifle.
The great thing about CLR is it works faster in the barrel than anything I ever tried period. And then alcohol will rinse it out with a couple of patches.
I use it all the time and it works great. I always soak my titanium suppressor in it that is cerakoted black and it doesn’t hurt the cerakote at all. Good stuff and another great video.
Great video... I was hoping that you would do this video. I have an extra MPA muzzle brake nut in nitrate finish that I am going to test in the CLR when I return from vacation. I will report the results...
Wow! I'm learning about gun cleaning from you Erik. Thank you very much. Boy, I really had no idea about what to do with my barrels. It makes sense; How could carbon in your rifling help you? Of course, it doesn't help at all!
I take everything Eric says as gospel, till I dropped my MDT carbon steel brake in the CLR for 2 hr . When I removed & washed the brake it had a black brown rust film all over . Took 30 min scrubbing with tooth brush & soap & water to clean it up .
Works fast. No need to let it sit. Get it in scrub with brush patch out with 99% alcohol. Patch dry. One damp patch of Remclean and another dry patch.... Done! Blued cromo barrel no issues.... Back to 1/2 MOA... THANK YOU ERIC.....
I don’t know how it compares but I use motor oil. It absorbs carbon fouling. Maybe it isn’t as fast. I can take the bolt carrier group out of my AR, remove the bolt, and then stand the bolt carrier upright in a plastic container. Put motor oil on and in the carrier. Come back next day and there will be a pool of jet black motor oil in the plastic pan. Wipe as much off as possible and good to go. Same thing with bolt.
I’ve been using this on non-alum parts of my rimfire suppressor. It doesn’t dissolve the lead but by the time it interacts with the carbon the lead is so much more softened/brittle that it flakes off relatively easily. The heavy deposits take a bit more work but much less than untreated parts. The titanium parts stay in for hours or overnite. The ss parts I take out a bit sooner as they will take on a little browning that scrubs right off with a toothbrush and #9. The cerakote finish doesn’t just come right off but it’s aging is accelerated. I don’t really care, it’s a suppressor, not a piano. The package cautions against exposure to aluminum and any acid will damage bluing. I’ve been using the same jar of clr since I first filled it. It’s dark and full of nasty sediment but the parts still seem to bubble vigorously as soon as they go in. CLR = carbon and lead remover 😉. If I had an ultrasonic cleaner I’d set the jar in the bath for a bit after the parts had soaked. I think all but the worst might rinse right off.
I was thinking the same thing that it would be good for rimfire cleaning.....until you mentioned aluminum and bluing. So I'm guessing not good idea for use on a ruger 10/22 or a savage model 64?or anything blued for that matter?
I’m not going to step in so far as to offer an opinion on where else this could be used. Personally, I’m not going to use it on blued surfaces or on precision steel parts (barrels, bolts). I do drop in things like the muzzle adapters for pistols but these are not projectile contact. It helps the lead to scrape out more easily. But I don’t want to damage the threads here, either. Ive found no cause to use this on anything 22 related other than the suppressor since it collects sooo much lead in pistol use.
Eric, you are the hardest worker on You Tube right now. Collaborating with Jerry and Matt, video recording competitions that does create distraction for a competitor that shoots at your level. Sharing your "secret tips" to help the shooting community. After watching you for some time I know you will just say something short and laugh it off and move on because you are too busy to waste your time on something you have little or no control over. Myself however can say what you tube is doing to gun related content creators is not only wrong it is unconstitutional which also makes it illegal. I see down the road a mass action law suit for damages against channels that have been discriminated against by You tube and the like. I like the new Keep em centered idea. Thanks for all your hard work! Mike B
Fantastic results, thanks for sharing my friend. I'm going to give this a try on my Oculus SS baffles. After a few hours in the wet tumbler with SS pins & Simple Green (full strength,) I'm not too impressed. It did well with my DA Mask SS baffles though. The Oculus baffles are stubborn little devils! Thanks again for the CLR demo.
@@Merk21 Works great, albeit a bit more work.. just needs a little more soak time. Still, no big deal, CLR is the way to go! Hope you're NFA jail time is short my brother! :)
I use a Dremel with a medium stone and rod extension to remove the carbon from my barrels but will try clr to help with the pesky little scratch marks LOL clr great idea thanks erik PS people I DONT REALLY USE A DREMEL. lol
Well..... CLR is not the end all of cleaners. If you are stainless, it's OK, however, and it's a big however, the R stands for Rust, and you know what bluing is, that's right it's Rust. It may clean your barrel nicely, but it will also remove bluing down to bare metal in a second. Do not use if you have and blue steel that might be exposed to CLR. Yes, I've done that and will remove your blue finish wherever it touches. I don't use it even on my stainless weapons as I might forget and also use it on the blue steel ones.
Brake cleaner is the best thing out there IMO. Doesn't matter what you're doing, it has you covered. Cleaning automotive parts? Got it. Killing wasps and other creepy crawlies? Got it. Cleaning firearms? Got it. Need some starting fluid but don't have any? Got it. It does it all! lol
I have a cerakoted wrench that was just a test piece when I was trying to figure out cerakote. I'll dump the wrench in a bottle this weekend to test. (Heat cure FDE)
4 days in, and the CLR has degraded the metal in the wrench. Around every nick in the coating, the metal corroded and expanded slightly, loosening the Cerakote's hold on the surface. The FDE cerakote is also slightly discolored green. In all, cerakoted parts may be good for a short soak, but I wouldn't go long.
Reminds me of when an air guard unit used simple green to clean landing gear and it worked great until they discovered cracking because of hydrogen embrittlement caused by the simple green on nonferrous metal. Since, they have made an aerospace formula.
@Erik Cortina - Pro Shooter I was curious on your thoughts on Ed’s Red home made gun cleaner & lube. I’ll definitely be trying the CLR on my Krieger M110 barrel I’m just gonna have to be careful around the hand guard upper and lower. Aero M5E1 set cerakote FDE
Man I thought I watched all your videos I don’t know how I missed this one!!!!!! I’ll be doing this tomorrow thanks man I appreciate you making these for us
Maybe the demonetized is because of how you are filling out the selection of what type of gun video. Use the one that says proper use in a gun range type of setting. For my cleaning I use Hoppes #9 these days but I have used Simple Green in a vibratory heated tank type of thingy to clean guns and it does a good job too. Not sure how it would be if you have any aluminum parts though.
I'm a gunsmith and I have reblued several barrels that people have used clr to try to remove minor surface rust and clr takes the bluing right off so stainless only
Do NOT leave CLR on carbon steel for more than a few minutes at a time. CLR will attack the carbon in the carbon steel. No issues with stainless steel. It is an awesome carbon cutter.
best youll find is stuff called Brulin 512 but its in a 5 gallon pail, gotta bum some from a turbine helicopter operator using small Bell or Md500 helis.. its made for that exact purpose..
...and demonetized! 😂
Of course
CZcams is just focking useless for posting great content ... SMH
Why, because of CLR?
I’m guessing because there are comments about AR’s. I uploaded this video yesterday and has been monetized the entire time. Comments is my guess.
@@ErikCortina Wow, I never knew they we're that strict. Completely ridiculous.
An alternative method taught to me by a military armorer that is good on blued parts.
Fill a large utility sink or kitchen sink with the hottest water you can stand.
A) Cover drain grills or any area that small parts can fall into.
B) Add a hefty amount of Dawn dishwashing soap.
C) Throw the entire broken down gun into the sink.
D) Thoroughly scrub everything. It takes about 3 passes with a bore brush and a barrel brush respectively. Smaller parts anout once with the "toothbrush".
E) Ensuring all parts are secure, drain the sink.
F) Refill the sink with super hot water and make sure all parts are rinsed.
The Dawn breaks down any carbon or oil buildup. The hot water serves two purposes; it helps with the soiling buildup and, this is the biggest point, when you take the pieces out, the high heat helps them dry quicker.
Oil everything.
While every other unit struggled for hours to pass an armory inspection, we turned our weapons in and were able to walk away to the shock of the armorers. Our weaponswere as clean as if they just came from the manufacturer prior to firing.
Still use this method on my AR to this day.
Had a pistol and a few mags that were oily fall into sand, hell to clean up and i resorted to super hot water sand dawn, worked perfect!
I do the same thing. The HOT water is the key!
I was taught that way too back in the 80's.
Will it work on polymer frames? I need to clean my tx22 but dont want to do anything to harm it since I hear not to clean polymer with any gun solvent. Say it dries it up over time and cracks.
@@UN-intelligent Should work fine. I mean, being honest polymer is just a fancy way of saying plastic.
I started using CLR a few weeks ago after watching one of your other videos. I had horrible accuracy issues with my rifle. After one time my accuracy snapped right back. Thanks for the advice.
Have used CLR for at least 30 years, cleaning house and janitorial work off and on. Great stuff. Would never have thought to scrub a barrel or parts with it. Thank you very much for the idea! You have a new subscriber.
AMAZING, absolutely amazing ! I have a barrel that just wouldn't let go of the icky barrel smeg, and now I'm victories. Ram-rod a tornado brush & CLR, then jag a few times, then repeat. Beautiful results !
I used some CLR I had after seeing your previous video and also ordered the patch-out. Shot the next day and had a .26MOA group with ES 10 and SD 3.6.... thank you sir.... I take what you say to the bank
Agreed.
I have been a massive fan of clr for years.
Great on stainless, caution with factory coatings.
ie pistol slides etc etc, it can take it back to bare steel.
Absolutely great on stainless barrels just be sure that's all its on.
Hey Eric, I recently found this page “ like yesterday” and I’ve been following you on Texasbarndominiums but I enjoy this more. Thanks for the vids. Big fan.
Just tried CLR on my 1911 pistol barrels... WOWZA!... best carbon removal I have ever experienced!
Thank you Mr. Cortina... absolutely love your educational youtube channel.
Do not get it near anything blued. Any finish that is a rust oxidized type finish. It will be gone quickly! That is the R of CLR.
Do not use it on aluminum either
It loves the bluing. Eats it for breakfast 🤣
@vettelover2009 its ok on carbon steel I think. Just not on the bluing
I used it on my dad’s Remington 700 30-06 blued. It worked great on the bore but it started to take of the finish off the action. I got scared and took the barreled action out of the stock and rinsed the entire thing with a garden hose.🤣 No major issue on the finish and it shot really well afterwards.
Good for stripping blue to refinish?
Great work Eric! I try this recently after you mentioned it in a previous post! Amazing how it strips the carbon out, and... best groups yet out of the 338 Edge!
Along the same lines, Zmax engine treatment works wonders on keeping stainless barrels clean. On a clean barrel, saturate the inside and then heat the barrel with a heat gun. While still hot, saturate again, and apply more heat (about 200F). Then just let it cool. Patch out the excess. This penetrates into the barrel and helps prevent the carbon from getting a hold. Works wonders on engine valves, so I tried it on one of my guns. It cleans super easy. Some of the best gun products aren't even marketed as such.
I've heard about using CLR. I was afraid of using it until I was this video. Thanks for sharing. I'm going to give it a try. I have learned the hard way that carbon fouling really sucks!
Thanks for these videos, the time & effort that goes into them is appreciated.
I would like to thank you for your excellent advice. I am not referring to CLR because I feel that I cannot use it on my blued chrome moly barrel - but rather for advice to use Teslong borescope as a cleaning assessment tool. Based on the borescope it turns out that my normal cleaning regime already removes all the carbon for me - but I found had a big problem with copper fouling. So I did an overnight soak using “Wipe Out” foam which turned all that copper to very dark inky blue liquid residue. It looks great now. Thanks again!
For what it’s worth.. My normal cleaning routine is to start with swab dipped in “Ed’s Red” thru bore guide, let the “Ed’s Red” soak an hour, then 20 strokes with my dewey rod with bronze brush, then push patches soaked in mineral spirits until it comes out clean, then dry patch. Turns out this works great for my carbon but not so much for copper.
‘May all your groups, be one hole.’, for me that’s the classic! It’s old school, I miss it already!
Great video, gonna use this added to my cleaning regimen from now on! Thank you!
Wow! I’m adding that to my cleaning routine now! Thanks for another awesome video, Erik.
Works great for titanium suppressor parts too. I usually cut mine with 50/50 distilled water.
I tried lemishine and water in an ultrasonic cleaner and was amazed at how well it worked on a stainless muzzle brake. Very fast, zero scrubbing.
Cheers!
Lol I’m a mechanic an shoot a ton of long range. I dropped a alternator in that stuff that wasn’t charging over night rinsed it with water put it back on the truck an been driving it for 2 years now haha
Love this stuff!!! Ran it through truck heater core!! Works wonders
Dude! I feel like I need to add you to my Christmas Card list. This works amazing, absolutely amazing! Thanks so much for taking the time to post this. You're the man!
I love your channel. I am not a match shooter and was never in the military. Your content really helps an old varmint hunter like me. Thanks for showing us tips and tricks
I tried it on my brake. It cleaned the crap out of it however it did slightly discolor the polished finish. Few passes across some 1000 grit wet or dry sand paper (wet) and the finish was restored. I found coating the muzzle of my stainless 1911 with a couple coats of One Shot helps stops the carbon tracing. I applied a couple coats to my brake. Haven’t put it to the test yet.
timing is perfect, was just researching CLR after seeing it on your bench
Works great on suppressors as well...takes lead right off baffles... works especially well on dirty 22 cans
CLR is amazing stuff! I use it on auto parts all the time. Wasnt sure how safe it would be on barrels... but now I know!
I recently viewed a video using CLR in a sonic cleaner of sorts cleaning an aluminum fuel valve shut off. The results were fantastic.
I know this is an older video, but I appreciate the info. I’m gonna give it a try. I recently learned that CLR is great for getting carbon off of exhaust tips so this makes a lot of sense.
Yes!! CLR!! I have been using this stuff for 2 years and any time I tell guys to try it, they look at me like I have no idea what I am talking about
Thank you for sharing CLR cleaner I never thought of using this clear on your barrels . I’ll have to give them a try
Follow up with 91% alcohol.
Thank you Eric. Lovin the channels.
@Erik Cortina - Pro Shooter Sir I truly appreciate you taking the time to answer questions
I am stunned. If this works that great in barrels then no more Iosso is needed unless you have a copper mine barrel. Thanks for your insight.
Thanks for the info. CLR has been deemed a carcinogenic agent so heed that warning about the gloves. Thanks for another great tip!
Extra points for the "band camp" joke...
😂
@@ErikCortina Please see my post.
👍👍🤣🤣🤣🤣gotta love the classic
Good thing you said to follow with 92% alcohol... Gotta have something to neutralize the acid in the CLR... or you will develop pits in the metal. cheaper the metal, the more likely to pit.
Erik I have a used rifle with a muzzle break much like yours in stainless. Even though the prior owner did pretty good cleaning the barrel I don't think he ever cleaned the muzzle break. I will try CLR as you did but since the muzzle break is welded to the barrel. I will have to hang it over the cup and use CLR like you did. Thanks for the tip!
I have been using CLR to remove carbon from my breaks and barrels without any adverse effects for the past few years good to see someone of Erick Cortina's pedigree else uses it also.
Brakes
Does it work on brakes other than Stainless Steel. I have a black APA Fat Bastard. Any advice would be appreciated. Thanks in advance.
Great question. I would also like to know?
Thanks Erik!
Im going to try it on my old blued steel factory Savage barrel.
Thanks Erik. New drinking game...every time Erik says carbon...take a drink. Great info lately, keep it going. Would really enjoy some more F-class loading and shooting. Enjoyed the PRS stuff.
Just tried it after getting my Borescope (Teslong Semi Rigid) and that'll explain why my 22-250 lost the handle. Oh my the copper and carbon... Spent a couple hours making it better... Seemed almost copper plated bore was achieved... This system works amazingly well..
No experience with stainless but it will etch regular steel if left submerged for a couple days.
Works great on nitride as well brother.
Good info/video!
I started using it long ago with my sonic cleaner for brass, it runs great, but it didn’t occur to me using it to clean the gun 👍🏻👍🏻👍🏻 nice tip.
I did have some concerns about CLR but I'll give it a try. I've had great luck with a product called "Free All". It's in a spray can so I just give the barrel a shot, soak a couple patches and run them out the barrel.
I ran this through my Bergara HMR Pro's barrel yesterday afternoon. Ran 3 wet patches from breech to bore using a bore guide and let set for about 15 minutes. The 3 wet patches were black as all get out. Patched it out and then used a bore solvent on a patch. Noticed an increase in filth from the wet patch of bore solvent showing that this did a good job. Scrubbed the barrel about 10 passes and patched it dry. Finished with a patch of alcohol and then a few more dry patches. This will now be my cleaning regiment. My break is blued steel, so I quickly wiped it down after the CLR patches inside and out. Probably should have taken it off, but its a pain to time right. Break looks fine after 24 hours too. Thanks man!
Haha. That movie reference is prime!
Going to have to try that with the brake on my 6.5 and AR.
People keep asking and I’m happy to share the story. I’m thinking when Erik and I get together at Nationals I will tell the story.
When I worked out in the mines I ran out of washing powder, I found "truck wash" in the company store, and as it was free, I figured it would be great to wash my clothes in. The first time I wore my clothes, I became itchy in the nether regions, but it wasn't really a problem. When I got home I realised all the skin on my balls started to peel off and my nuggets were red raw, the funny part was I didnt think it was from the truck wash, so I went and saw the company nurse about it, and it was only then the penny dropped about what had happened.
We would like to hear that story 😁
@@Ceiszi it’s in here czcams.com/video/O0it8x6qFYs/video.html
As you said “major changes before big match”. I think changing from beer to pure alcohol is big. Hehe just joking. Would like to hear more of these. Thanks for sharing.
I have yet to hear this story. Did I miss something, or did you? 🤔
If you shoot a revolver you know how the carbon builds up around the forcing cone and on the outside of the cylinder and cylinder face.
The CLR wipes the cylinder clean with little effort. Unbelievable. Wet a patch and it wipes away.
Yup, I've been cleaning my super redhawks this way for years.
I gotta try it on mine now!
LOVE your videos. Practical, experience-based and straightforward. Thanks.
I have been cleaning my muzzle breaks with CLR for a few years already great stuff, like Erik said I had only use it on SS muzzle breaks.
Does it work on non stainless steel or would it damage a black break for example ?
@@terryblenkinsop8329 Carbon steel which is not very corrosion resistant might not like it too much.
I didn’t have Evaporust on hand but I did have CLR and used it to remove a little surface rust from an older Stanley needle nose pliers made from boron vanadium steel alloy. Several hours soaking and brass wire brushing did the job.
You could probably have just rinsed the brake off at the tap and gotten most of the carbon off after the CLR soak. We've used it to clean lime from the pans under some bunny cages and rust from plumbing fixtures (city water and the toilet is NASTY!).
I think the "demonetizer" was actually showing the barrel of your rifle.
The great thing about CLR is it works faster in the barrel than anything I ever tried period. And then alcohol will rinse it out with a couple of patches.
Denatured alcohol or isopropyl alcohol for rinsing?
I use it all the time and it works great. I always soak my titanium suppressor in it that is cerakoted black and it doesn’t hurt the cerakote at all. Good stuff and another great video.
Was wondering about titanium- have an aac 300ti that needs cleaned. - RED
Thanks for the great tip Eric TC
I use to have mates in short range bench rest and full bore 1000 metres who were using CLR in the early 90s here in Australia.
Great video... I was hoping that you would do this video. I have an extra MPA muzzle brake nut in nitrate finish that I am going to test in the CLR when I return from vacation. I will report the results...
I have a black APA Fat Bastard break. Did it damage your nitrate finish or should this just be used with Stainless Steel ?
great video Erik!
Wow! I'm learning about gun cleaning from you Erik. Thank you very much. Boy, I really had no idea about what to do with my barrels. It makes sense; How could carbon in your rifling help you? Of course, it doesn't help at all!
Pro shooter solves cleaning issues with this one easy trick, overpriced gun cleaning product companies hate him!
😂
@@ErikCortinaWhat's it do to copper fouling?
Good information thanks Erik
That stuff flat out works Erik! What powder are you running in your 284 shehane?
Thanks Erik
I take everything Eric says as gospel, till I dropped my MDT carbon steel brake in the CLR for 2 hr . When I removed & washed the brake it had a black brown rust film all over . Took 30 min scrubbing with tooth brush & soap & water to clean it up .
Works fast.
No need to let it sit.
Get it in scrub with brush patch out with 99% alcohol.
Patch dry.
One damp patch of Remclean and another dry patch.... Done!
Blued cromo barrel no issues....
Back to 1/2 MOA...
THANK YOU ERIC.....
Gunsmiths buddy of mine showed me how well it works
I don’t know how it compares but I use motor oil. It absorbs carbon fouling. Maybe it isn’t as fast. I can take the bolt carrier group out of my AR, remove the bolt, and then stand the bolt carrier upright in a plastic container. Put motor oil on and in the carrier. Come back next day and there will be a pool of jet black motor oil in the plastic pan. Wipe as much off as possible and good to go. Same thing with bolt.
I may try this on the face of my stainless revolver cylinders and on the frame at the top strap above the forcing cone. Thanks!
I’ve been using this on non-alum parts of my rimfire suppressor. It doesn’t dissolve the lead but by the time it interacts with the carbon the lead is so much more softened/brittle that it flakes off relatively easily. The heavy deposits take a bit more work but much less than untreated parts. The titanium parts stay in for hours or overnite. The ss parts I take out a bit sooner as they will take on a little browning that scrubs right off with a toothbrush and #9. The cerakote finish doesn’t just come right off but it’s aging is accelerated. I don’t really care, it’s a suppressor, not a piano. The package cautions against exposure to aluminum and any acid will damage bluing.
I’ve been using the same jar of clr since I first filled it. It’s dark and full of nasty sediment but the parts still seem to bubble vigorously as soon as they go in. CLR = carbon and lead remover 😉. If I had an ultrasonic cleaner I’d set the jar in the bath for a bit after the parts had soaked. I think all but the worst might rinse right off.
I was thinking the same thing that it would be good for rimfire cleaning.....until you mentioned aluminum and bluing. So I'm guessing not good idea for use on a ruger 10/22 or a savage model 64?or anything blued for that matter?
I’m not going to step in so far as to offer an opinion on where else this could be used.
Personally, I’m not going to use it on blued surfaces or on precision steel parts (barrels, bolts). I do drop in things like the muzzle adapters for pistols but these are not projectile contact. It helps the lead to scrape out more easily. But I don’t want to damage the threads here, either.
Ive found no cause to use this on anything 22 related other than the suppressor since it collects sooo much lead in pistol use.
Great video and info Erik, thanks. Would CLR work on cleaning brass as well??
Nice info thanks keep them small and centered.😃
Lemishine and CLR are fine for stainless, but shouldn't be used with anything else. The citric acid can turn nitride pink, and can strip bluing.
Eric, you are the hardest worker on You Tube right now. Collaborating with Jerry and Matt, video recording competitions that does create distraction for a competitor that shoots at your level. Sharing your "secret tips" to help the shooting community. After watching you for some time I know you will just say something short and laugh it off and move on because you are too busy to waste your time on something you have little or no control over. Myself however can say what you tube is doing to gun related content creators is not only wrong it is unconstitutional which also makes it illegal. I see down the road a mass action law suit for damages against channels that have been discriminated against by You tube and the like. I like the new Keep em centered idea. Thanks for all your hard work! Mike B
Thank you
The bottle specifically says dont use with brass but I can say it does very well cleaning cases too
thanks now I gotta go check every gun barrel after you planted that in my head. Simple things work better sometimes
Just a tip for you Erik! Do not leave CLR on your hands for extended times.
Just saying! Don't ask who did it or how I know!🤣🤭
As many are, awaiting for the replacement for youtube! Eric best content available! Keep it up.
Fantastic results, thanks for sharing my friend. I'm going to give this a try on my Oculus SS baffles. After a few hours in the wet tumbler with SS pins & Simple Green (full strength,) I'm not too impressed. It did well with my DA Mask SS baffles though. The Oculus baffles are stubborn little devils! Thanks again for the CLR demo.
Hey Jim, how did it work on the oculus baffles? I've got one that'll hopefully be out of jail soon!
@@Merk21 Works great, albeit a bit more work.. just needs a little more soak time. Still, no big deal, CLR is the way to go! Hope you're NFA jail time is short my brother! :)
@@MackDaddy8154 Thanks man! Praying but I've got another can that is getting close to 300 and nothing yet 😬
CLR does take the copper colored coating off (TiN?) of Oculus and Obsidian baffles. Definitely works on the carbon though.
@@jzeke1712 Maybe a little, but mine still have a copper color. I'm not certain they're Tin coated..
I use a Dremel with a medium stone and rod extension to remove the carbon from my barrels but will try clr to help with the pesky little scratch marks LOL clr great idea thanks erik PS people I DONT REALLY USE A DREMEL. lol
Thanks for posting eric. Have you ever tried it in an ultrasonic cleaner? Shotgun gas pistons are notorious for carbon buildup ill give it a try
Well..... CLR is not the end all of cleaners. If you are stainless, it's OK, however, and it's a big however, the R stands for Rust, and you know what bluing is, that's right it's Rust. It may clean your barrel nicely, but it will also remove bluing down to bare metal in a second. Do not use if you have and blue steel that might be exposed to CLR. Yes, I've done that and will remove your blue finish wherever it touches. I don't use it even on my stainless weapons as I might forget and also use it on the blue steel ones.
Awesome! I have a blued barrel that needs re bluing. Should work good for that.
Did it harm the bluing?
I’ve always used break cleaner to get the carbon out then douse everything in oil to keep it from corroding and rusting the weapon
Brake cleaner is the best thing out there IMO. Doesn't matter what you're doing, it has you covered. Cleaning automotive parts? Got it. Killing wasps and other creepy crawlies? Got it. Cleaning firearms? Got it. Need some starting fluid but don't have any? Got it. It does it all! lol
I have a cerakoted wrench that was just a test piece when I was trying to figure out cerakote. I'll dump the wrench in a bottle this weekend to test. (Heat cure FDE)
24 hours in and it doesn't look discolored or anything. Gonna let it sit for a week.
4 days in, and the CLR has degraded the metal in the wrench. Around every nick in the coating, the metal corroded and expanded slightly, loosening the Cerakote's hold on the surface. The FDE cerakote is also slightly discolored green.
In all, cerakoted parts may be good for a short soak, but I wouldn't go long.
@@number6mbw Thank you!
Our CLR in Australia is clear in colour. I wonder if it's a different composition. It still works well.
Hmmm, I'm thinking for using on the breech plug on my muzzleloader ?
Reminds me of when an air guard unit used simple green to clean landing gear and it worked great until they discovered cracking because of hydrogen embrittlement caused by the simple green on nonferrous metal. Since, they have made an aerospace formula.
@Erik Cortina - Pro Shooter I was curious on your thoughts on Ed’s Red home made gun cleaner & lube. I’ll definitely be trying the CLR on my Krieger M110 barrel I’m just gonna have to be careful around the hand guard upper and lower. Aero M5E1 set cerakote FDE
I might try that in my Ultrasonic Cleaner see if it does even better
Great stuff mate I’ll get some .
Man I thought I watched all your videos I don’t know how I missed this one!!!!!! I’ll be doing this tomorrow thanks man I appreciate you making these for us
Try rust buster on stainless steel barells it cleans very well, I use sweets 7.62 bore solventits good too
That’s amazing, hopes it works that well with carbon steel barrel.
Maybe the demonetized is because of how you are filling out the selection of what type of gun video. Use the one that says proper use in a gun range type of setting. For my cleaning I use Hoppes #9 these days but I have used Simple Green in a vibratory heated tank type of thingy to clean guns and it does a good job too. Not sure how it would be if you have any aluminum parts though.
great video thanks !
Thanks for sharing. I was going to ask if ok for blued barrels . But seeing in the comments it’s not a good idea to do so.
I'm a gunsmith and I have reblued several barrels that people have used clr to try to remove minor surface rust and clr takes the bluing right off so stainless only
Do NOT leave CLR on carbon steel for more than a few minutes at a time. CLR will attack the carbon in the carbon steel. No issues with stainless steel. It is an awesome carbon cutter.
Most stainless steels do contain carbon.
I have seen recommendations for using window cleaner as a bore cleaner. I guess because of the ammonia.
best youll find is stuff called Brulin 512 but its in a 5 gallon pail, gotta bum some from a turbine helicopter operator using small Bell or Md500 helis.. its made for that exact purpose..