Are Flare Nut Wrenches Any Better? Let's Settle This!

Sdílet
Vložit
  • čas přidán 6. 04. 2024
  • Wrench Sets: Snap On, Proto, Williams, Mac Tools, Crescent, Kobalt, GearWrench, Duratech, Milwaukee, Performance Tool, Craftsman, Matco Tools, Quinn, Efficere. Several sizes of wrenches were tested to determine overall best performing wrench set. Wrenches tested repeatedly revealed a huge durability issue for several brands.
    Are flare nut wrenches a scam? Almost all of the flare nut wrenches became bent during the review. My "opinion" is that manufacturers make "soft" wrenches to avoid warranty claims. Once bent, the wrench will cause damage (round off) a fastener very easily instead of loosening the fastener or nut. A properly hardened tool offers much more strength but is also much more likely to break, instead of just bending.
    I bought all of the wrenches and supplies used to test the wrenches to ensure an unbiased review. So, thank you for supporting the channel!
    ➡ Thank you very much for supporting the channel through Patreon: / projectfarm
    ➡ Thank you for supporting the channel through memberships:
    / @projectfarm
    ➡ An easy way to find past videos along with products tested: bit.ly/2FCrBpk A big thanks to Jim for putting this together.
    ➡ Merch: project-farm.com
    ➡ Click here if you'd like to subscribe: / @projectfarm
    ➡ As an Amazon Associate I earn from qualifying purchases.
    ➡ Products Tested In This Video (in no particular order):
    Proto: amzn.to/46gPgCD
    Williams: amzn.to/3MNqCm3
    Crescent: amzn.to/3srePmH
    Craftsman: amzn.to/3MIujJG
    Kobalt: amzn.to/49varnj
    GearWrench: amzn.to/47sp1tG
    Duratech: amzn.to/49CWnZ2
    Performance Tool: amzn.to/3sEdsko
    Efficere: amzn.to/3QAZojL
    Mac Tools: Available at the Mac Tools Online Store
    Quinn: Available at Harbor Freight
    Snap On: Available at the Online Snap On Store
    Milwaukee: Available at Home Depot
    Matco Tools: Available at the Online Matco Tools Store
    Wrench Extension Tool: amzn.to/3JSDRRB
    Videography Equipment:
    Canon EOS R6 Mark II: amzn.to/4aErF18
    Canon 70D Camera: amzn.to/31b5Gy0
    Azden Microphone: amzn.to/34d3DLE
    Go Pro Bundle: amzn.to/3Ca0ZVN
    This video is only for entertainment purposes. If you rely on the information portrayed in this video, you assume the responsibility for the results.
  • Jak na to + styl

Komentáře • 3,8K

  • @deepghetto8968
    @deepghetto8968 Před měsícem +1409

    If it weren't for you there would be a lot of people needlessly wasting their hard earned money on suspect tools. Todd, you are getting up there with the likes of many other revered members of the human race like Mr. Rogers, Steve Irwin, David Attenborough and others. You are a continuous bright light in a sometimes dark world. Thank you for your steadfast, honest work. It means a lot to a lot of people. Be well.

    • @ProjectFarm
      @ProjectFarm  Před měsícem +112

      Thanks so much!

    • @Prosecute-fauci
      @Prosecute-fauci Před měsícem +53

      That’s deep

    • @therealking6202
      @therealking6202 Před měsícem +24

      ​@@Prosecute-fauciYour username definitely isn't.

    • @martinmiller8953
      @martinmiller8953 Před měsícem +10

      Well said I love when he says(very impressive)

    • @alexcallas8222
      @alexcallas8222 Před měsícem +12

      Todd's contributions to humanity cannot be over stated! Nothing less than the Presidential Medal of Freedom, Kennedy Center honors, and UK full Knighthood are deserved. Better yet: the reverse side of our quarter dollar coin- Todd's bespectacled likeness, with the words "We're Going To Test That". Generations going forward will know and revere his name!

  • @betabry42
    @betabry42 Před měsícem +710

    Back in the day when Sears backed Craftsman it was a no brainer. 75% of the quality for 25% of the price. And replaceable in minutes by driving to Sears. Nowadays, I’m with Cousin Eddie.
    Thanks for keeping those luxury toolmakers on their toes by giving us real data!

    • @aired-downdisconnected4125
      @aired-downdisconnected4125 Před měsícem +28

      Craftsman still does that warranty on handtools. (at Lowe's) . I just replaced a ratchet recently.

    • @flyinwalenda
      @flyinwalenda Před měsícem +24

      Thank Eddie Lampert for that downfall !

    • @ixfxi
      @ixfxi Před měsícem

      @@aired-downdisconnected4125 Yeah but their replacements arent worth a damn, unfortunately. Its such a shame how that brand turned to shit.

    • @ProjectFarm
      @ProjectFarm  Před měsícem +31

      You are welcome!

    • @user-sx1ov1bu2w
      @user-sx1ov1bu2w Před měsícem +7

      MENARDS FTW

  • @johnthew5798
    @johnthew5798 Před měsícem +71

    My buddies and I played the Project Farm drinking game. (A beer for every "very impressive" occurrence)
    Not everyone made it until the end...
    I love this channel!!!

    • @MrOshirinoana
      @MrOshirinoana Před měsícem +3

      I play that game with "..we're gonna test that.."

    • @tellyfaulkner3466
      @tellyfaulkner3466 Před měsícem +1

      Gluttons for punishment. Classic. lol

    • @pgramsey1
      @pgramsey1 Před 26 dny +1

      Is it even possible to drink beer that fast? I would think that Wild Turkey 101 would be the only way to play this game.

    • @davidparker9676
      @davidparker9676 Před 16 dny +1

      My buddy is a diehard Gearwrench and Matco fanboy, he always told me I was wasting my money on Snap-On and the better performing brands. Looks like I will send him a link to this video. Very Impressive.

  • @EricA-nr2jr
    @EricA-nr2jr Před měsícem +9

    My suggestion: make a website that compiles all your data and recommendations for viewers. Provide affiliate links for your recommendations according to your data so you earn compensation and help out viewers. Data is so vital for everyone and your testing methodologies are some of the most reliable I have seen

    • @Wolfcone
      @Wolfcone Před 2 dny

      Pin this. This is golden advice.

  • @crabwalk7773
    @crabwalk7773 Před měsícem +251

    Ex retail worker here. Just a reminder that, if you can wait, tools often come on sale in May/June for Father's Day. At least that was in the past....

    • @ProjectFarm
      @ProjectFarm  Před měsícem +36

      Thanks for sharing.

    • @xzx4696
      @xzx4696 Před měsícem +14

      I have Fathers Day marked on my calendar for this one reason 😅

    • @___Bruh__
      @___Bruh__ Před měsícem +11

      That makes so much sense now that I'm reading it. Don't know why I never thought of this before. Thanks for sharing this tip.

    • @TheSaw410
      @TheSaw410 Před měsícem +3

      Sales? In retail? No way!

    • @punkem733
      @punkem733 Před měsícem +4

      @@TheSaw410 They did say "At least that was in the past" lol

  • @Timberland1963
    @Timberland1963 Před měsícem +72

    One of the things I like about all these videos is that Todd always says where a product is made. It saves me a lot of time since I will avoid buying anything made in China if it is possible. Thanks

    • @ProjectFarm
      @ProjectFarm  Před měsícem +4

      Thanks!

    • @adambyrd2193
      @adambyrd2193 Před měsícem +2

      Like-minded soul here. I will gladly spend more to buy American

    • @forzaguy1252
      @forzaguy1252 Před 26 dny +4

      Try not to buy Chinese, but i will gladly buy Taiwanese made, they seem to know what they are doing

    • @DarthCiliatus
      @DarthCiliatus Před 8 dny

      @@forzaguy1252 ROC > CCP

  • @TheMrBrendo
    @TheMrBrendo Před měsícem +83

    I dont know why, but your content is relaxing in a way that i cant explain…maybe its because the world can be so crazy and emotional, but there is something so soothing, systematic and logical about the way you breaking down the technical specs and capabilities of random tools. Like a meditation…thank you, please dont stop. It is a service for the world

  • @OcularPerceptions
    @OcularPerceptions Před 16 dny +2

    Love your channel. I don't shop for tools until I've swung by your channel first.

  • @darkerbinding6933
    @darkerbinding6933 Před měsícem +145

    FWIW, the Proto wrench that snapped is warranted for life. Considering the very high level of force that took to break it, normal use is unlikely to see a similar failure. Thanks for the great review.

    • @ProjectFarm
      @ProjectFarm  Před měsícem +11

      Thank you for sharing!

    • @jayslager1200
      @jayslager1200 Před měsícem +4

      I have the proto and they never fail me.

    • @ensidfkgnur
      @ensidfkgnur Před měsícem +14

      For all the tools he buys he probably has a garage filled with broken/mismatched tools from the tests. It they warranty replace the Proto he may, for once, wind up with a full set of useful tools!

    • @sulljason
      @sulljason Před měsícem +6

      @@ensidfkgnur Even though he has like 10-20 sets of a lot of tools he probably still struggles to find the one he needs lol. Now it's just a massive pile. Maybe he's SUPER organized and avoids using the tools from the channel.
      Was wondering how he made much money but just occurred to me he must make bank off affiliates especially if a cheaper higher volume product does well. No offense to him for doing that ofc he invests a lot of time and money and is straight forward about it.

    • @lasskinn474
      @lasskinn474 Před měsícem +5

      @@sulljason he has a patreon with 2300+ paying members, so that would cover some of it and the channel is fairly popular and a lot of the viewers are from usa and are adults in age ranges that have spending power so I reckon he does allright with ads as well. I like that it doesn't have sponsors because that would throw the point of the channel away as a fan to watch. like most of the stuff bought people just give him the money to buy for through the patreon, it's a big part of what makes the larger tests possible.
      affiliate links don't pay much, generally, since people need to spend a lot of money for you to make much out of it. well maybe they're over the average for him considering bunch of people would use his links just 'cause they're his links if they're buying something they watched reviews for.

  • @hemansr3893
    @hemansr3893 Před měsícem +169

    We all appreciate what you do for us Todd!!! THANK YOU! 👊👊👊

  • @josephrepetsky546
    @josephrepetsky546 Před měsícem +13

    I said it once & I'll say it again. When I worked sales at Home Depot. I always pulled your channel up & told everyone from your DIY'er to Professional Contractors/Mechanics. Very informative you are & the amount of money you saved myself & other's is absolutely astonishing. Thanks again.

  • @HellhoundXIV
    @HellhoundXIV Před 14 dny +1

    This channel became my go-to for reviews. No bs, no favoritism, and directly going to the point. Companies should ask for your stamp of approval.

  • @jvcyt298
    @jvcyt298 Před měsícem +159

    When you need to work on anything with a brake line or a fuel line, a flare nut wrench is essential. 20 or 30 years ago, I would have recommended Craftsman, but those days are long gone. My Dad gave me his old Proto 1/2 inch socket set when I turned 18, so it's nice to see that they are still making a good reliable tool no matter what corporation runs the company.

    • @ixfxi
      @ixfxi Před měsícem +12

      After years of wondering why so many difficult tube nuts would get rounded from my Craftsman flare wrenches, I bought myself a used set of SnapOns and never looked back. It was easier to stomach the buy since they were used, but hands down they are strong and reliable. Nice to see this video proves that.

    • @ProjectFarm
      @ProjectFarm  Před měsícem +5

      Thanks for the feedback.

    • @1pcfred
      @1pcfred Před měsícem +12

      I don't have flare nut wrenches. I do have Vise Grips though. If Vise Grips can't get it then the line gets cut and it gets an impact socket on it. It's coming apart one way, or another. I can guarantee that.

    • @jvcyt298
      @jvcyt298 Před měsícem +11

      @@1pcfred ;So, I guess that you're the type of guy who rips open a zip lock bag with your teeth. You know, finesse is not a four letter word.

    • @KameraShy
      @KameraShy Před měsícem +5

      Likewise. Fortunately, I filled my tool box with Craftsman back in the 70's.

  • @nutsnbolts76
    @nutsnbolts76 Před měsícem +131

    This is going to be a great comparison video. The quality of these wrenches vary a lot.

  • @user-bs6th7vq2p
    @user-bs6th7vq2p Před měsícem +5

    This is the only channel I trust for product reviews and comparisons. Thank you for your service. You truly look like you enjoy every minute of it.

  • @shang0h
    @shang0h Před měsícem +4

    I'm sad that I hadn't seen this channel until now, but also kind of excited for myself that I get to watch it all for the first time and everyone else here can't have that experience! Awesome, thorough and straightforward reviews for all kinds of things I actually need and use around the house and property, and it puts in drastic relief how bad the internet has gotten for plain old information these days. I've never subscribed to a channel so fast, and I hope you're being rewarded.

    • @ProjectFarm
      @ProjectFarm  Před měsícem

      Thanks! Thanks for watching and subscribing!

  • @reserved50
    @reserved50 Před měsícem +64

    i like how you included both styles of snap-on wrenches, a quality open end will out perform a lower end flare nut wrench😃

    • @ProjectFarm
      @ProjectFarm  Před měsícem +2

      Thanks!

    • @fastinradfordable
      @fastinradfordable Před měsícem +6

      And a vice grip will crush it slightly but perform way better than either.
      Because a clamped on vice grip has zero slop.
      Which no socket can do

    • @davidpowell3347
      @davidpowell3347 Před měsícem +1

      Especially on harder metal.

    • @reserved50
      @reserved50 Před měsícem +12

      @@fastinradfordable that works but.... the best setup i've used if you have room is clamp a vicegrip on the outside of a flare wrench. Prevents the vicegrip from crushing the nut.

    • @NoNo-df5tl
      @NoNo-df5tl Před měsícem

      I like how snap on and Williams are the same tool with different stamps, but performed completely different.

  • @ArnCital
    @ArnCital Před měsícem +68

    I shop thrift stores and buy just about every old tool that I can; half the fun is figuring out what the tool is. It is sad that the tools are often from an old gentleman or gentlewoman who passed away without heirs to cherish the craftsman and his or her tools; may they Rest In Peace. I am in the same boat with no heirs so... I have taken box wrenches and sliced a very narrow slot to fit over the tubing. Then I clamp down on the box end with a pair of vise grips to really put some force on the flare nut. I also use Freeze, Kroil, or Knock-r-Loose overnight if possible. Thank you for another great tool test.

    • @ixfxi
      @ixfxi Před měsícem

      Vice grips? How much room do you have to work with? You're better off giving the tube nut a whack to shock it, that will unseize the nut real nice.

    • @ProjectFarm
      @ProjectFarm  Před měsícem +2

      Thank you for sharing!

    • @FlorinArjocu
      @FlorinArjocu Před měsícem +4

      That gentleman/woman saying is funny. In Europe we have some similar ones when buying a second hand car: it belonged to an old lady that was only driving it to the church :)

    • @lasskinn474
      @lasskinn474 Před měsícem +1

      @@FlorinArjocu well, I reckon what he meant he just goes to the yard sale after the passing.
      not that common in europe at least in places i've been.

    • @tellyfaulkner3466
      @tellyfaulkner3466 Před měsícem

      @@lasskinn474 OP opened with "I shop thrift stores" not yard sales.
      What about Sunday flea markets, swap meets etc because there are always old tools at those events? They do/have them in Europe?

  • @TheReal1953
    @TheReal1953 Před měsícem +32

    Once upon a time I worked at a gold mill in CO. Our tools of choice for everyday work were New Britain and Proto. You can't imagine the conditions and abuse they suffered. The Proto tools were cruder but STRONG. Then later I had a big farm in MO and again, invested in New Britain and Proto. All the bigger tools were Proto and never once had a failure of any kind. They were cared for better than at the gold mill but used as hard. Thanks for this review!

    • @woodrowsmith3400
      @woodrowsmith3400 Před měsícem +3

      I worked in a NAPA store in the '80's and have a lot of New Britain tools. Still.

    • @ProjectFarm
      @ProjectFarm  Před měsícem +5

      You are welcome! Thanks for sharing.

    • @TheReal1953
      @TheReal1953 Před měsícem

      @@woodrowsmith3400 Love New Britain tools. So much so that I scoured the Net for the New Britain 'story'. Turn of the 20th-century tool company that made lots of familiar brands...if you're an old guy.

    • @MitzvosGolem1
      @MitzvosGolem1 Před měsícem

      Proto awesome 👍

    • @SharpAssKnittingNeedles
      @SharpAssKnittingNeedles Před měsícem +1

      Badass! Colorado native here and geological engineering student. Did you work at the big-ass bitch in Victor? Visited there on several field trips and really cool operation that seems passionate about what they do and excited to share it with future geology nerds!

  • @coreyswann8735
    @coreyswann8735 Před měsícem

    Brilliant and extremely helpful work as always! I always enjoy watching your tests and when I'm watching at home even my wife will sit and watch, which is a testament to how good your content really is as she generally hates watching youtube!

  • @bobbykately9621
    @bobbykately9621 Před měsícem +79

    Went from 50 vies to 250 real quick, been watching you for years , can't wait till me and my future kid can watch your videos!

  • @kontakt4321
    @kontakt4321 Před měsícem +61

    Love that you measured the width of the deformation that the wrenches leave. That really helps quantify the depth of the taper and the actual working surface. Thanks for all that you do!

  • @electronicsNmore
    @electronicsNmore Před měsícem

    An extremely useful hand tool that I've used countless times over the years. That's a really great torque tester. Your thorough testing and close up images are top notch! Thanks for the video

  • @richardray7972
    @richardray7972 Před 24 dny

    I just wanted to say thank you so much for what you do. Your tests are absolutely thorough and that means a lot. Keep doing what you do. You are amazing

  • @eldoradocanyonro
    @eldoradocanyonro Před měsícem +55

    I find it interesting how the Craftsman wrenches look--and behave--very differently from the ones in my garage, which I bought almost 30 years ago.
    Another great job! Thanks!
    Well said about having the harder tool break rather than damage the fastener!

    • @ProjectFarm
      @ProjectFarm  Před měsícem +7

      Good Point! Thanks and you are welcome!

    • @ixfxi
      @ixfxi Před měsícem +12

      The quality is just not the same. USA vs... you know

    • @LTVoyager
      @LTVoyager Před měsícem +12

      The C in Craftsman now stands for Chinesium.

    • @Fister_of_Muppets
      @Fister_of_Muppets Před měsícem +3

      ​@ixfxi Agreed. I have some older Craftsman tools and they're rock-solid. The new stuff is junk.

    • @jorper2526
      @jorper2526 Před měsícem +5

      @@ixfxi Really, it's not USA vs X.. It's USA companies who have outsourced to whoever can do it cheapest.. Chinese manufacturers could make the highest quality.. But Craftsman doesn't want that anymore. They want maximum profits. Quality means keeping every piece of the manufacturing process in good shape. It means more maintenance of the equipment, lower lifespan on the "replaceable" pieces, stricter QC.
      But no, instead they increased the tolerances to allow for inferior products to be sold. And they keep selling. I really wonder what the profits margins are like for their tools.

  • @dunhell9929
    @dunhell9929 Před měsícem +71

    right when my food was ready i got a notification that my favorite youtuber posted a video

  • @oldskoolfattieg
    @oldskoolfattieg Před měsícem +1

    You really do deserve any sucess thats come your way, because the amount of work you put in for these videos is staggering. I appercite it, anytime i decide to buy a tool or something i always check your channel 1st to see if youve done a test.

  • @fire304
    @fire304 Před měsícem

    You content just keeps getting better! So glad you're including tool truck brands in your regular testing. Here's a test idea; they say they didn't make em like they used to. Would be a fun video if you could test a few vintage tools against the modern set to see how they stack to. I have a set of Craftsman from the early 80's and I swear they hold up much better than most of the newer tools I have (on the rare occasion that one breaks I loath having to warranty them because the new stuff is thicker and not as good).
    Keep up the good work, I'm sharing this one with all my gear head friends!

    • @ProjectFarm
      @ProjectFarm  Před měsícem +1

      Thanks, will do! Thanks for the suggestion.

  • @justjay3750
    @justjay3750 Před měsícem +21

    i used the headlight restore kit recommended, the sylvania one. it looks brand new, thanks again. i dont trust a single youtuber other than you. i always use the products you reccomend and i am always glad i did. you are the man!

    • @ProjectFarm
      @ProjectFarm  Před měsícem +2

      Thanks!

    • @owensomers8572
      @owensomers8572 Před měsícem +1

      Haha, I can say that for several products, but have been really impressed with the windshield crack/chip repair. I had tried several kits over the years but none seemed to do much. But the kit Todd tested with the best results has worked well for my gravel attracting windshields!

  • @artillerybuff2000
    @artillerybuff2000 Před měsícem +52

    Great test Todd, thank you very much!
    As a retired professional automotive technician that started buying these tools back in the 1970's, I can tell you back then nothing compared to Snap-On. I used to bail out other techs out all the time with my "at-the-time" way better quality Snap-On tools. When they started stripping fasteners, quite often my Snap-On tool would save the day. However, the patents ran out on the flank drive sockets and wrenches a long time ago because even the cheaper tools are using the same technology now. Very nice to have less costly options like Proto; if I was starting out today I'd probably not even look at the Snap-On line and save thousands of dollars...

    • @ProjectFarm
      @ProjectFarm  Před měsícem +4

      Thanks and you are welcome!

    • @1pcfred
      @1pcfred Před měsícem +3

      Snap-On is still doing the best heat treating in the industry. That's what you're paying for. Heat treating is an art. Snap-On is practicing the art at a very high level too. They use a triple treatment process. Which is one treatment more than everyone else does.

    • @larrydudgeon2846
      @larrydudgeon2846 Před měsícem +1

      Back in the day the Mac line wrenches were way better. How do I know. My dad had both Snap-on and a set of Mac and the Mac's were better by a long shot.

    • @artillerybuff2000
      @artillerybuff2000 Před měsícem +2

      @larrydudgeon2846 I had/have both too and MAC's were good, but not better than Snap-On in the '70's, not even close...

    • @TigDegner
      @TigDegner Před měsícem +4

      @@1pcfred unfortunately for Snap-On, producing the best tool available requires more than good heat treating. While they're good on paper, Snap-On is consistently beaten in the field by Knipex and Klein in pliers, MAC and Proto (and Williams and etc.) in ratchets, sockets, and wrenches; Wera and Wiha in screwdrivers, and so on. Which would be fine if Snap-On was priced what they're worth. These days, most Snap-On tools are worth about half what they cost IMO. They're still good, but not $$$$ good.

  • @ColombianLNP
    @ColombianLNP Před měsícem +4

    These are essential videos! Thanks for everything you do man! Cheers from Colombia amigo !

  • @Billbobaker
    @Billbobaker Před měsícem +1

    the ones I bought a couple decades ago all finally broke.
    Great Video. Thank you sir for sharing it.

  • @derekfarley5899
    @derekfarley5899 Před měsícem +16

    One of the few creators left that I will actually sit through full length form. Been waiting on this vid

  • @Sainte305
    @Sainte305 Před měsícem +36

    I'd go with Proto as well. None of their tools have ever let me down.

    • @ProjectFarm
      @ProjectFarm  Před měsícem +3

      Thanks for the feedback.

    • @1pcfred
      @1pcfred Před měsícem +3

      Stanley Black & Decker owns Proto today.

    • @Sainte305
      @Sainte305 Před měsícem +3

      @@1pcfred I know, but I still have had good luck with them. And for the price they’re pretty hard to beat, but no tool or brand is perfect.

    • @pikaonyoutube2139
      @pikaonyoutube2139 Před měsícem +1

      Career ending injury lmao🤣🤣🤣🤣 i agree wirh you proto tools you cant go wrong with

    • @1pcfred
      @1pcfred Před měsícem

      @@Sainte305 Proto got bought by Stanley and Stanley is indeed a company that will not be beaten. Their bean counters don't leave any meat on the bone. Which can affect overall quality.

  • @scoobtoober2975
    @scoobtoober2975 Před měsícem +1

    Dang it. bought a set to do brake lines. the craftsman about 18 years ago. Tried to use them. They wouldn't break th connection. Sloppy fit for the metric set. I never knew there was a quality difference back then. You have highlighted the problem and what the right tool is for the job. THANKS from the bottom of my heart. I'd easily do a brake job today with two knipex parallel pliers. All day. Back then we used two regular vice grips and marred the fittings to death. But that is all that would work back then. THANKS again

  • @skiball83
    @skiball83 Před měsícem

    Thank you for all of your hard work buddy. Well respected and the respect is well deserved.

  • @tjhemrick
    @tjhemrick Před měsícem +43

    Guys over at Torque Test Channel giving you a shout out in one of their videos speaks volumes about your rep. Thanks for all you do to bring us the numbers. It's greatly appreciated.
    Can you do sockets? Just regular sockets. 6-point vs 6-point, 12 vs 12, etc. After that, you can have a grand finale of 6 vs 12 vs _______. I've looked and all I found was wrenches, damaged fasteners sockets etc.

    • @ProjectFarm
      @ProjectFarm  Před měsícem +4

      Thanks! Thanks for the suggestion.

    • @nleippe
      @nleippe Před měsícem +1

      @@ProjectFarm 6 vs 12 vs spline would be great.

  • @bewernia
    @bewernia Před měsícem +40

    I would have never expected a wrench to stretch like that. Over time, and maybe not a long time, the wrench will "wear out". Really enlightening.

    • @ProjectFarm
      @ProjectFarm  Před měsícem +1

      Thank you for sharing!

    • @AN-kg4ei
      @AN-kg4ei Před měsícem +6

      I know it refutes the idea of a decent stand alone tool, however, if you clamp the flare wrench with vice grips, it will break fasteners before slipping. If you don't have a spare flare nut and don't want to roll the dice, give it a try. I love my 10mm SnapOn flare but after watching Todd's torture testing, I wish it was a Proto. 👍

    • @harryharry3193
      @harryharry3193 Před měsícem

      THUS the importance of replacements for free-warranty.
      all wrench's will stretch with strong use.

    • @bewernia
      @bewernia Před měsícem +1

      @@harryharry3193 would they replace a tool if it isn’t obviously broken? Would you have to get out your calipers? I just never thought of a wrench stretching before. I thought they broke or didn’t break.

    • @reverse_engineered
      @reverse_engineered Před měsícem +1

      It's important to note that stretching (plastic deformation) is generally a result of excessive stress. Keep in mind, he's using a cheater bar and seeing how much they can take before completely stripping the nut. In practice, I'd hope you don't do the same with your tools. Under more reasonable stress, the metal shouldn't leave the region of elastic deformation, where there is no permanent elongation and it will return to its original size. While materials will fatigue from repeated stress, that's typically on the order of 100k - 1 million cycles - way more times than you'll ever use a wrench.

  • @fZionists78
    @fZionists78 Před měsícem

    The additional suggestion/recommendations at the end is great advice and appreciated.
    Most experienced mechanics know what they like. But even as a middle aged carpenter I never considered the size of nut would change the desired style of wrench. Upon hearing your explanation, it all makes sense.
    Wise advice.

  • @moto_moo
    @moto_moo Před 12 dny +1

    Absolutely love the channel!!! What I want to know and I'm sure many others want to know is how you maintain the energy thru the whole video. What kind of coffee do you drink and/or what do you do to maintain that energy? Very Impressive!!!!!!

  • @MAGGOT_VOMIT
    @MAGGOT_VOMIT Před měsícem +24

    Williams makes some really great tools. I've got a set of their aluminum handle pipe wrenches that I added to my work-box years ago and they've worked just as good as my Rigid brand.

    • @ProjectFarm
      @ProjectFarm  Před měsícem +4

      Thank you for sharing!

    • @gus473
      @gus473 Před měsícem +2

      Good to know, thanks! 😎✌️

    • @pnotuner1
      @pnotuner1 Před měsícem +3

      Where can I find Williams tools?

    • @MAGGOT_VOMIT
      @MAGGOT_VOMIT Před měsícem

      @@pnotuner1 Been almost 20yrs ago but I think I bought mine from Grainger, when I bought my set of GENERAL Internal Pipe-Wrenches.

    • @MAGGOT_VOMIT
      @MAGGOT_VOMIT Před měsícem

      @@pnotuner1 It's been almost 20yrs but I think I bought them through Grainger when I bought my set of Internal Pipe-Wrenches.

  • @Lesterman_1
    @Lesterman_1 Před měsícem +11

    Thank you for letting me know the best performing line wrenches, without having to buy them myself! I was getting very tired of my gearwrench open ends as I feel they were the worst lol and I wanted a better set of open-end wrenches to deal with certain Flair nuts. I didn't want to go for line wrenches because then, I would have still had "bad" open-ends. I decided to go with the Mac Tools RBRT wrenches with the 6-point Box end. They have been phenomenal! I treat them like my candy tools 🤣

  • @user-nv9wk9vc1l
    @user-nv9wk9vc1l Před měsícem

    Great tests this week. I look forward to watching on Sundays.

  • @Free_Ranger_CT110
    @Free_Ranger_CT110 Před měsícem

    These videos are so good, you are definately teaching this old dog some new tricks (& saving some money) And learning that 'you get what you pay for' isn't always correct. Cheers!

  • @thedownwardmachine
    @thedownwardmachine Před měsícem +7

    I like the learnings section at the end of the video, I hope this becomes a regular addition. Thanks for your hard work!

  • @F4Wildcat
    @F4Wildcat Před měsícem +8

    Thank you PJ for another stunning video & all the great work you are putting into this!

  • @Black70Fastback
    @Black70Fastback Před měsícem +1

    very interesting that a regular open beat so many dedicated flare nut wrenches. quality can mean so much.
    I will be adding some new tools to my Christmas list based on this video.
    Thanks again.

  • @TrevorGehman-bk7yr
    @TrevorGehman-bk7yr Před měsícem

    Dude you rock. Keep doing what you're doing. Please don't ever change!

  • @RoyRogers-ll5ji
    @RoyRogers-ll5ji Před měsícem +5

    Your tests and evaluations are very much appreciated, always look to your videos when making decisions on what to buy!! Thanks

  • @_BAD_MERC_
    @_BAD_MERC_ Před měsícem +7

    What a fantastic test!! Not only was it thorough - it was informative in layman's terms and explained how and why a particular tool will perform better. You sir have once again checked ALL the boxes!

  • @jayblz1
    @jayblz1 Před měsícem

    I love this channel , this man it’s a master at this , keep the good content going

  • @lepunicorn
    @lepunicorn Před měsícem

    I love how reliable and applicable your testing is. That said, spring cleanup is here! I'd like to suggest chippers/leaf shredders, weed killer concentrates, and wheel barrows!

    • @ProjectFarm
      @ProjectFarm  Před měsícem

      Thanks! Thanks for the suggestion.

  • @davaogary7042
    @davaogary7042 Před měsícem +13

    I know 1st hand from years (er-decades?) of doing my own DYI on my vehicles, the poor fit (sloppiness) of flare wrenches. I also found that metric flare wrenches can be a good fit on SAE brake line fittings. A 12mm can be a good substitute for a 1/2", a 14mm a good sub for a 9/16". These metric wrenches fit tighter on the nut. Really love your channel.

    • @ProjectFarm
      @ProjectFarm  Před měsícem +1

      Thanks!

    • @1pcfred
      @1pcfred Před měsícem +1

      A half inch is 12.7mm and 9/16" = 14.29mm so the metric sizes are a smidge smaller. But then there's tool tolerances. A half inch wrench wouldn't fit on a half inch fastener. It'd just be too tight. I mean you could hammer it on. I'm not sure how you'd get it back off. Generally anything less than 4 thousandths difference is an interference fit. You need some slop. 3/4 - 19mm is another close match too. They're basically the same size. You don't need both of those tools.

  • @MariaRodriguez-bp1tl
    @MariaRodriguez-bp1tl Před měsícem +7

    Finally! I have a set of flare nut wrenches set but I am constantly worrying if there is something better, I look for your videos before making a purchase so you can imagine the breath of fresh air to see a new video with exactly what I need
    Thank you so much for your work 💚

    • @ProjectFarm
      @ProjectFarm  Před měsícem +2

      You are welcome! Thanks for the feedback.

    • @nazaa999
      @nazaa999 Před měsícem

      What's the specific use for flare nut wrenches?

    • @fastbusiness
      @fastbusiness Před měsícem

      @@nazaa999 They are used to tighten/loosen the connectors (nuts) that are used on tubing that controls the flow of fluids. Some examples: brake line fittings, hydraulic hose fittings, air hose fittings, water lines, etc. These fittings are generally made of softer metals and are usually difficult to replace if damaged.

  • @ngt8042
    @ngt8042 Před měsícem

    Your work is impeccable and priceless. Thank you for all you do. Would LOVE a Bore Scope comparison.
    Side note: This man and his channel has over double the subscribers of mine and many folks favorite band, TOOL. How's that for excellent content!

    • @ProjectFarm
      @ProjectFarm  Před měsícem

      Thanks!! Thanks for the suggestion.

  • @NTATchannelNickTaylor
    @NTATchannelNickTaylor Před měsícem

    I've had a Williams master set for some years. I only get to use them when working on my track loader and backhoe or power steering / air fittings on one of the Rigs. I have no complaints out of them. Another good show!!! 👍🏽

  • @SPMech1
    @SPMech1 Před měsícem +13

    Trying to remove a Power Steering line on my Wife's 78 Mustang II back in the early 80s my Craftsman flare wrench failed me. I was able to borrow a Snap-On flare wrench that worked flawlessly. Needless to say I bought a Snap-On set.
    Great Test as ALWAYS ! ! ! ! ! ! Thanks ! ! ! ! ! !

  • @sirmister4411
    @sirmister4411 Před měsícem +5

    I hope the tools companies watch your videos so they can learn how to improve their tools keep up the good work thanks

  • @DarkDraconX1
    @DarkDraconX1 Před 14 dny

    Never got the notice for this. I really needed this video. Thank You Project Farm.

  • @deanmckean7770
    @deanmckean7770 Před 19 dny

    For almost 60 years I've used a combination of snap on, proto, and craftsmans, depending on application. But my go-to is Armstrong. If you you could, give these a try to see if i have put to much faith in them. Great job as usual. I don't spend any money on anything, until i see if you put it through a test. Thank you very much for all you do. Best channel on CZcams, period.

  • @mopartony7953
    @mopartony7953 Před měsícem +12

    Excellent! Flare nut wrenches are where never to skimp on. Deserves a Part 2. To include Vintage Craftsman, Blackhawk, Cornell, Armstrong, Gedore, Stahlwille, Hazet, Beta, SK.

    • @Yosho359
      @Yosho359 Před měsícem +7

      Add in Wright Tools as well!

    • @ProjectFarm
      @ProjectFarm  Před měsícem +3

      Thanks! Thanks for the suggestion.

    • @clutteredchicagogarage2720
      @clutteredchicagogarage2720 Před měsícem +3

      I have a lot of vintage sk and also several vintage Armstrong and Wright in my tool collection. I used to work as a car mechanic. My older mac and snapon tools are also generally very good, but I would not say that they’re always better than older sk or Armstrong or williams, etc.
      I loved the ergonomics and quality of old sk. I haven’t used any sk tools newer than 20 years old, and so I cannot comment on the quality now.
      Those old made in the USA tools were great though. Some tools made in taiwan are pretty good. Some European tools (but not all) are also very good. I think some gear wrench tools are made in China, but their top end stuff is probably better than the average hand tool at a big box store in the USA (also likely made in China).
      Craftsman tools vary greatly in quality. The best craftsman wrenches from decades ago were solid, but some of the old stuff was also terrible. I am guessing that all new craftsman hand tools are pretty bad.

    • @SaltMinerOU812
      @SaltMinerOU812 Před měsícem +1

      Tekton, Capri

    • @1pcfred
      @1pcfred Před měsícem +2

      The problem with vintage tools is they're no longer available to purchase today. So it is pointless to test them now. Because no one's going to be able to get them.

  • @MattsAwesomeStuff
    @MattsAwesomeStuff Před měsícem +3

    I loved the added context in the conclusion this time. More of this more often please.

  • @DynamicDesign144
    @DynamicDesign144 Před měsícem +1

    I was glad to see you tested two different sizes from each brand - makes it a little more likely you'll catch quality inconsistencies from wrench to wrench

  • @Bertminator
    @Bertminator Před měsícem

    I always am entertained at seeing how cheap tools outperform the super-expensive one's. It just goes to show that it's not always high price that determines a tool's quality. The first time I used my flare nut wrench was when I did a brake job and the nut was practically sealed to the caliper. It's cool to see that these tools have a purpose, YA, a box wrench's open end might have freed up that sealed nut, but I wasn't going to risk it, and the flare net I purchased at "Princess Auto" (Canada's equivalent to Harbor Freight) did the job just fine. Thanks for your videos Todd!

  • @carseat1921
    @carseat1921 Před měsícem +7

    You are the entirely the reason to why I puchased all my power tools a specific brand based on my personal needs.
    Thank you for all the helpful information you've done for us

  • @DanKoning777
    @DanKoning777 Před měsícem +14

    Week in/week out there's never any mystery as to why you have 3.14M subscribers. Thanks for all the time, effort and thought that goes into each video
    that we benefit from-especially that of resisting those who'd love nothing more than to have you $howcase/promote their products. Thanks again. God bless.

  • @samhicks97
    @samhicks97 Před měsícem

    This is invaluable information, appreciate the uploads.

  • @briananderson7008
    @briananderson7008 Před měsícem

    Great video. Proto is what my grandfather left me to work with as a tool set. Torque wrenches stopped working and they couldn't fix them. Still a great company.

  • @chrishensley6745
    @chrishensley6745 Před měsícem +8

    Sad Matco/Williams and Craftsman has went to the dumps.....years back when they were made in U.S. ...they were top notch or close to Snap-on and Proto was always a good brand as a darkhorse for some reason....but those that have been around,Proto makes good tools and boxes still today. Love your videos man!

    • @dlewis9760
      @dlewis9760 Před měsícem +3

      Don't blame the "Made not in the USA". Any country is capable of making anything. It's not magic. The "Names" are still US names and they find someone to build their stuff to their specs. They don't want to pay, even in outsourcing to a foreign company. Less quality and cheaper for them to make? Great combo. You'd think less labor went into it, they'd use the savings and put it into quality. Funny how, phones can be made "Over there" with no problems. My Samsung S21 was made in Vietnam. Very good chance the chips in your phone are made in Taiwan.

    • @ProjectFarm
      @ProjectFarm  Před měsícem

      Thanks!

    • @1pcfred
      @1pcfred Před měsícem +2

      Williams didn't do bad. They came out third. First in value I'd say.

  • @kmac2923
    @kmac2923 Před měsícem +7

    Yess been waiting for this one!

  • @mrgcav
    @mrgcav Před měsícem

    Another well rounded review by Project Farm. Great job.

  • @JonathanFisherS
    @JonathanFisherS Před měsícem +25

    "I was on a road trip when a brake line ruptured" dude whatever brand of underwear you were wearing needs a review here.

  • @999brbr
    @999brbr Před měsícem +7

    i wish you could do multimeter comparison video next time ❤

  • @liam.da.ghostboy
    @liam.da.ghostboy Před měsícem +29

    Saw you in a clip of Westin Champlin's video yesterday. It was from Matt's offroad recovery's offroad challenge in Utah.

    • @ProjectFarm
      @ProjectFarm  Před měsícem +18

      That was a fun event!! I enjoyed meeting everyone who attended!!

    • @liam.da.ghostboy
      @liam.da.ghostboy Před měsícem +5

      @@ProjectFarm sure looked like it was a blast.

    • @RealJeep
      @RealJeep Před měsícem +2

      Was Matt giving a symposium on how too commit insurance fraud? Something he's very good at.

    • @kyleh3615
      @kyleh3615 Před měsícem +1

      ​@@RealJeep what happened with insurance fraud?

    • @RealJeep
      @RealJeep Před měsícem

      @@kyleh3615 Matt pled no contest in Utah for defrauding Insurance companies. Google it.

  • @christopherclark170
    @christopherclark170 Před 27 dny

    I’ve recently been looking into and getting interested in the 3D printing world. 3D printers, different kinds of filaments and their strengths and weaknesses, etc. I think it could be a really good area of tools and hardware for you to get into. It would bring in a whole community of viewers.
    I love your videos! Keep it up!

    • @ProjectFarm
      @ProjectFarm  Před 27 dny +1

      Thanks, will do. Thanks for the suggestion.

    • @christopherclark170
      @christopherclark170 Před 25 dny

      @@ProjectFarm Awesome! Here’s some more specific ideas. I’m getting a Bambu Labs X1-Carbon soon. There are a lot of reviews out there that talk about features of different printers and review them that way, so it was pretty easy to choose the printer I wanted for my needs. So much of 3D printing is getting the settings right. The videos out there that compare the strengths of filament types and stuff are not nearly as in depth or scientific as your videos. Comparing PLA, PETG, ABS, ASA, PA-CF, and other carbon fiber blend filaments. Utilizing different part geometries to test different kinds of applications. Compression strength, layer adhesion, and just strength in different ways in the way that you format your reviews would be so valuable to so many people. There are different brands of filament and that makes a difference, but I’m more interested in the strengths and weaknesses of filament materials as a whole.
      Thanks for considering all of this!

  • @corysavage609
    @corysavage609 Před měsícem

    Hi,
    How are you doing today? I am doing pretty good myself.
    I just would like to say thank you for getting to another one of my video ideas.
    I love all the great work and the great information that you have provided us.
    I would like to see you try testing: utility knifes to find out which manufacturers are the best.
    I hope that you and your family take care until next time.

  • @Austin23191
    @Austin23191 Před měsícem +4

    I use a 3/8 7/16 gearwrench flare nut wrench at work for fuel oil burners. It works a lot better than the adjustable wrench I used to use which slipped if a fitting had been torqued down too hard

  • @bttfdmc1984
    @bttfdmc1984 Před měsícem +5

    I agree with you I’d rather have the tool break than just stretch that way you know it’s been compromised rather than stretch and not notice until it’s too late.
    I know it would be subjective and a bit inaccurate but I’d like to see a revisit a similar test with used/old wrenches to see if one that has been well seasoned holds up or does poorly against the new one.

  • @DustinScottErickson
    @DustinScottErickson Před 13 dny

    I always struggle when deciding when to "spend the money" on specialized tools. Your videos help me get more value for my money! 💰

  • @derekmelyndadeckens2982

    Thank you for all of your testing of these different tools and brands. As a consumer is great to know where the best performance and best value lies with these manufacturers. High performing manufacturers that produce a quality product also deserve to be rewarded as well.

  • @Ataraxia_Atom
    @Ataraxia_Atom Před měsícem +3

    I have the cheap harbor freight set and they have been a godsend, always use the right tool especially when working with brake and hydraulic fittings

  • @bobbykately9621
    @bobbykately9621 Před měsícem +9

    Only channel i wouldnt mind watching an ad at the beginning of the video!

  • @trentvlak
    @trentvlak Před měsícem

    Good point on the breaking vs bending. Thanks for the video.

  • @probesport
    @probesport Před měsícem +1

    Fantastic video, one of your top reviews. Thanks!

  • @danmartin8892
    @danmartin8892 Před měsícem +5

    It just ain't Sunday without a trip to the farm. Thanks for another great video.

  • @Hoaxer51
    @Hoaxer51 Před měsícem +10

    Maybe next time you can test the Wright brand wrenches, they’re comparable with Mac and other higher quality brands and they’re made in the U.S. also.
    I already own a set of Wright tubing wrenches but I’d like to see how they compare to the others you’ve tested, there’s nothing like having Project Farm show you what you really have and how they stack up if you’ve already purchased that product.
    Thanks for showing us how different wrenches compare to each other, great job as always.

    • @ProjectFarm
      @ProjectFarm  Před měsícem +1

      Thank you for the video idea!

    • @SaltMinerOU812
      @SaltMinerOU812 Před měsícem +2

      Yeah like a round 2, and add like capri, tekton

    • @abrahamsandwich4532
      @abrahamsandwich4532 Před měsícem +2

      @@SaltMinerOU812 I'd like to see other brands tested, as well as Vise Grips and Eagle Grips that often get used instead of a proper wrench.

    • @SaltMinerOU812
      @SaltMinerOU812 Před měsícem

      @@abrahamsandwich4532 shame Malco already discontinued their grips.

    • @Turdafonzanoon
      @Turdafonzanoon Před měsícem +1

      I have the wright line wrenches. Don’t use them often and don’t have any other brands to compare them with. But they are solid and a snug fit. I was hoping they would be included in this comparison. But they are hard to come by sometimes

  • @Build-It-Faster
    @Build-It-Faster Před měsícem

    You are a blessing to all CZcams DIYers. Have you done a video on RV In Line Water Filters??

    • @ProjectFarm
      @ProjectFarm  Před měsícem

      Thanks! Thanks for the suggestion.

  • @liljoeii6091
    @liljoeii6091 Před měsícem

    Awesome video you put some real detailing in your videos and I appreciate that

  • @flowerpt
    @flowerpt Před měsícem +20

    Crescent wouldn't have needed to run a 34% discount today if they knew Todd was dropping this video!
    Twenty one clams for both metric and SAE? Yes, please.
    Good job, India.

    • @KameraShy
      @KameraShy Před měsícem +1

      It seems every time a product is subject of a CZcams review, the price skyrockets. I expect the 34% discount will disappear real fast.

    • @freespirit1975
      @freespirit1975 Před měsícem

      It seems like for price, performance, and "not made in China", Crescent goes for the win. If I made my living with the tools, I'd probably go with the US made Proto (BTW the small set is now over $100). I put the three-piece Crescent set for $10.99 in my Amazon list. We'll see how long the price stays that low. I have lots of Crescent tools made in USA that my Dad bought and used including Crescent "Crestoly" crescent wrenches.

  • @Dragoninja833
    @Dragoninja833 Před měsícem +5

    Project Farm: A true American Hero!
    We're lucky to have you! Thanks for all your hard work!

  • @A----T
    @A----T Před měsícem

    Top notch comparison. Thanks for your honest reviews.

  • @N20Joe
    @N20Joe Před měsícem

    This channel is pure gold!

  • @411Adidas
    @411Adidas Před měsícem +3

    Very impressive 🤙🏽

    • @JSFGuy
      @JSFGuy Před měsícem

      Watt is?

    • @ProjectFarm
      @ProjectFarm  Před měsícem +1

      Thank you and hope you enjoy the video!

  • @l5514598844k
    @l5514598844k Před měsícem +17

    You could test different types of drywall joint compounds and tapes. Mesh tape vs paper vs fiber

  • @rickflores4077
    @rickflores4077 Před měsícem

    Great job thank you.
    That's the kind of testing I've been asking about.

  • @GtfoEdaters
    @GtfoEdaters Před měsícem +1

    After what, 15 years? Still my fastest subscription to any channel. Very impressive!

  • @otarsulava
    @otarsulava Před měsícem +244

    Suggested video: Best TACTICAL PEN - Water resistant, glass break capability, retainer clip and overall durability test, can it write down on paper in freezing temperature - 32F or less, compare extra functionality if it may have, like: integrated screw driver or flashlight, as an example

    • @ProjectFarm
      @ProjectFarm  Před měsícem +30

      Thank you for the video idea!

    • @xploration1437
      @xploration1437 Před měsícem +28

      Or get a pencil.

    • @Kamunchu
      @Kamunchu Před měsícem +45

      I am pretty sure the word "tactical" has lost all meaning.

    • @gus473
      @gus473 Před měsícem +15

      ​@@KamunchuNot if you're in Marketing! Say, can I interest you in a tactical can opener....? 😉✌️😎

    • @HSKFabrications
      @HSKFabrications Před měsícem +9

      Pretty sure that fisher space pen he's been using for the last 20 years would win 😂

  • @cje26
    @cje26 Před měsícem +9

    Video suggestion: Revisit of diesel fuel additive comparison. Comaring Seafoam, Archoil, Hot Shots Secret, Stanadyne, ACDelco, F Bomb, and Amsoil everyday treatments to compare their detergent properties, cetane boosting capability, efficiency improvement, lubricity when diluted in fuel, and ash content left after combustion would be a tremendous help to the diesel community.

    • @ProjectFarm
      @ProjectFarm  Před měsícem +1

      Great suggestion! Thank you

    • @lmt7816
      @lmt7816 Před měsícem +1

      Love this idea, particularly, lubricant additives for those of us with CP4 variants.

    • @abmtz8537
      @abmtz8537 Před měsícem +1

      Don’t forget Lucas fuel injector cleaner

    • @cje26
      @cje26 Před měsícem

      @@abmtz8537 I never realized it was safe for diesels. It definitely belongs on the list!

    • @HSKFabrications
      @HSKFabrications Před měsícem +1

      And opti-lube

  • @chash7335
    @chash7335 Před měsícem +1

    Great test of wrenches for the most frustrating job. Williams also makes a ratcheting flare nut wrench that I believe is stronger than the typical open box design. I have a few of them-they are expensive-but worth it. Thanks again.

    • @ProjectFarm
      @ProjectFarm  Před měsícem

      You are welcome! Thanks for the feedback.

    • @geraldrossouw4425
      @geraldrossouw4425 Před měsícem

      Indeed, I would have liked to see that type tested as well, the Proto J3800A set is similar. Also curious how a normal adjustable wrench will compare (as you can adjust for a perfect fit), as well as something like Knipex's Pliers Wrench.

  • @danielj.schneider5162
    @danielj.schneider5162 Před měsícem

    Thrilled to see this comparison! Thank you!
    I think it's worth noting that since flare nut wrenches are almost always used on hydraulic coupling nuts and other similar fittings that usually have tapered threads or other characteristics that mean the wrench will rarely be up against a boss like in your test, the taper may not actually play a huge role in real-world performance. That said I suspect your rankings wouldn't be affected much anyway.
    Another note: I have loved when you've included an older, USA-made Craftsman tool for comparison in these hand tool reviews; I wonder how an 80s-era Craftsman would have performed here, since I still have several and they've never let me down.