Nissan Altima front strut / wheel bearing / control arm / tie rod ( part 2 )
Vložit
- čas přidán 8. 12. 2023
- THE MECH A NIC’s amazon store ,here’s the tools I use
www.amazon.com/shop/themechanic
If a MECH A NIC video helped you consider donating to my patreon account to help support the channel. / the_mech_a_nic
or my paypal
paypal.me/jonathanrenteria1986
THE MECH A NIC’s Instagram page
/ the_mech_a_nic
THE MECH A NIC’s facebook page
/ the-mech-a-nic-1356996...
Thank you for watching my video, I appreciate the support ! - Auta a dopravní prostředky
I've never seen struts with the little mounting arm things. I love that strut compressor. OH! I also agree with the tightening and control arm bushings, I do it the same
The spring compressor works good enough but it can be picky on which struts are easier to do. Sometimes it's a real pain in the butt to use it but it always gets the job done 👍
I have to check my front left wheel bearing and hub on my Nissan Note (Versa) E11 from 2010 and I feel ready to do that thanks to your videos. Greetings from France.
Hello! It's pretty much the same as this car to check the wheel bearing. Glad the videos helped you
Great 2 part video
Thanks for watching! Now I need to look into the air bag issue...
Great work ! Your thoughts on lining up the bearing and knuckle with an old abs sensor before assembly ? Hope the boss is happy with the altima.
That's a good idea also. I didn't have a old ABS sensor laying around and didn't feel like removing the one off the car. Lol she said she barely notices a difference while driving 🤷♂️ .... women lol
Going to give my 2011 Camry all this on all 4 wheels along with brakes. 240K
That's some good miles on it 👍
@@themechanic6117
Runs great and is my daily driver. I want something new but can’t justify it so I am going to spend $1K on parts and give it a suspension and brake overhaul. Doesn’t use oil either which is rare at this mileage. But…I am serious about maintenance intervals. New master cylinder and rubber lines and bleeding ABS pump should give me a firm pedal. Pads and rotors are good (about year old). Also going to look at replacing knuckle bushings while they are off.
Good luck with all the repairs, new cars can be nothing but headaches, I'm all for the repairs 👍
11:50 the one she told you not to worry about
Exactly 🤣
what are the torque specs for each bolt ??? Please the information would be great...
Thank you for the video :)
; also do you plan on changing out the REAR components ?
If NOT would the torque specs be the same ??
Hey! Saw you had an HHR 5 years ago- I bought one just recently for my first car and it runs great- just the tail light turn signals don’t work. Do you have any advice? Also- I seem to have put it into anti-theft mode trying to start it with the spare key a a few times and trying to do the 30 minute reset I saw described online for recognizing a new key or whatever. It’s a 2011 HHR LT and now- it won’t even turn on. I’m wondering if the battery is dead or if just unhooking the battery for 10 minutes or half an hour or something then trying the initial key again to get it out of anti- theft mode will work. I know nothing about cars and I’m thinking about having it looked at so I don’t have to mess with it but if it’s something I can do I’d like to.
Your wrong, ok your not lol thanks for the nice video
🤣👍 fight me ! Lol thanks for watching
@@themechanic6117 lmao
What wheel bearing brand you put on? trynna get mine done.
Not sure I remember. Probably a Timkin
Was the AB’s slot on other side exactly 180 degrees? Did you try rotating the assembly? I’m familiar with wheel hubs, but not Nissan specifically.
Just wondering if slot on other side was offset to compensate for left vs right.
The other slot was not 180° out, I tried rotating it and that didn't work either.
@@themechanic6117 okydoky then. Just asking. Good job nonetheless.
Which strut mount bearing brand did you use?
KYB , not long ago I used beck/ arnley strut bearings on some Hondas, I had to do both of those jobs over again as soon as I installed them because the bearings were binding and making noise . KYB has been good so far 👍
@@themechanic6117 Awesome thanks! I was thinking of either just replacing the mount bearing or buy the Monroe quick strut.
Just tried to change the strut mount and I couldn't compress the coil back down far enough to get the new mount on.
Hey brother I have a 2016 nissan altima and this code came up p0420 and p015b I went to a shop and they told me that I need a new catalytic converter 2 new oxygen sensors and a full tune up can you help me, do I really need to do all this ??? Thank you
For those codes that's most likely the correct repair that needs to be done
So it's not worth buying the 2 oxygen sensors and changed them that won't change anything,I need to change the catalytic converter ???
With a p0420 just changing the sensors could potentially be a waste of money . Usually it is a bad cat convertor, but the shop wants to change the sensors anyway which is understandable.
@themechanic6117 thank you bro, you are the bets CZcams mechanic I always watch your videos and mostly the when you do the nissan altima 2014