DIY Assembly Juki DDL-8700 How To Step by Step
Vložit
- čas přidán 19. 01. 2020
- In this one hour DIY video we will show you how to assemble the Juki DDL-8700. We cover step-by-step in 8 sections on how to put the table, stand, motor, and head together. Then we show you the basics of operating the machine. We offer the Juki DDL-8700 in the pieces detailed in this video at www.cutsew.com/Juki-DDL8700--...
Section One shows the unboxing of the items you receive when ordering your Juki DDL-8700 unassembled from www.cutsew.com. One box contains the Juki machine head and the sewing machine servo motor. The larger box holds the legs, tabletop and other necessary items.
Part Two covers the tools you will need to perform the entire task. We outline the entire list from wrenches to scissors.
The Third segment explains how to put the table and legs together. Every single bolt and nut are shown to lessen the mystery of what goes where. We explain exactly how to connect the braces to the legs so that the machine is structurally sound.
In the Fourth Section, you will see how to mount the servo motor to the table while it is still upside down. The technique of assembling it upsidedown makes for less lifting and faster work.
Part Five details exactly how to connect the operator pedal to the motor so that the machine will sew as expected. Skipping a section like this might leave you with rubbing parts or maybe just a machine that won't run.
Segment Six explains how to properly unbox the Juki DDL 8700 sewing machine head safely and without damage to the product. You also see all the accessories that come inside this box. You may be surprised that this is where the thread stand is kept.
Section Seven of this DIY video will show you step-by-step on how to attach the head to the table. There are quite a few small details that must be executed in a certain order. Critical guards are installed to protect the operator from moving parts.
Eight. In the last portion, we go over the basic operations of your fully assembled sewing machine. We show you how to thread the machine. We also show you how to load the bobbin and adjust the stitch length.
Special Thanks to Royalty Free Music from Bensound - Jak na to + styl
You are a lifesaver. The instructions JUKI sends are pathetic. Bless you.
Hahaha you got instructions?
Thank you. I just got my DDL-8700 today and my husband and I were able to put it together with no problems thanks to your video. Thank you again!
Great to hear!
I was looking to buying a Juki but it would be disassembled and you need someone to assemble it for you. So whenever I need help, I always go to CZcams. I am so happy I came across your video. You are the best instructor, with the help of your partner who took his time to put it together, you made it very easy to try and tackle it myself. Thank you so much!! Keep up the good work.
all I can say is that this is one of the best tutorials I’ve seen. Very layman focused!! Just excellent and thank you!!
I TRULY enjoyed watching this! Loved the way you explained every step. You and your assistant are true professionals!
Fantastic work!
This helped tremendously while building my machine.
Thank you!
Thank you - because of your video I was able to assembly my table and machine
Just got myself a DL8700, but like someone else said in the comments, the instructions Juki provided weren't great. So thank you for this super detailed and very helpful video!
Thanks for the compliment Sanna. We hope you'll stick with us for more videos.
Thank you so much! We could not have put my Juki machine together without you. Your step by step was perfect.
Glad I could help!
🤓 Lifesaver you are !!. Got my Juki yesterday, fully assembled BUT couldn't make heads or tail of bobbin winder!. 🙏
Thank you very good video, God bless you!
The legs included with my moms machine were quite different, but overall this video was awesome in getting it setup. Thanks for providing such great instructions for all kinds of people.
Yeah, this is, of course, our set up. Depending who you order from, there will be some differences, but we are making the most helpful videos that we can.
thank yall so much! I wanted to build my own that way I would know what to do if anything went wrong- and this video is awesome!!
Thank you so much for providing such excellent step-by-step instructions. My Juki DU-1181N arrived yesterday with no instructions for installation. I had read that everything is the same as installing the DDL 8700 except the fly wheel, so this was extremely helpful. There were some very minor differences (like the type of screws), but this video was excellent! THANK YOU!
Glad we could help.
This video is awesome! helped me put my machine together the right way! Thanks guys!
this helped SO MUCH while assembling my machine... Thanks :)
Rovell Gaither Great to hear. Let us know if you need anything else.
Aww man I really can’t wait to put one together that way I can make any future repairs right here at home.
Thanks - The best instructional video I’ve seen
Glad it was helpful!
THANK YOU SO MUCH!!!! Super super helpful!!
I love the CUBA 🇨🇺 baseball cap the tech is wearing.
Thank you for this- incredibly helpful. Loved the tool list;)
Glad it was helpful!
Thank you for your information it is very useful. I followed and completed in 6 hours It is working fine. My table was different so I followed different CZcams Thank you Eugine
You guys are awesome!!! Thank you for sharing this!!! 🤩
Thanks for watching!
muchas gracias, me ha servido de mucho su video, saludos desde Perú
Thank you very much for this video , the steps are clear to follow. My machine is running good
This video was very helpful, it was easy to follow and to understand! Thank you!
Thanks for your SUPERB vidéo. I can't wait to get my machine. Great work. It seems so simple when you show and explain. I feel confident I can do it too. God bless you all !
Glad it was helpful!
Cool I finally have a reason to dust off the metric tools. I’m saving up for it!
Thank you thank you!!!!
You guys are absolutely incredible. Though there were a couple parts I got stuck on like which screws to use with what, your video is the reason I assembled everything properly. Thank you, thank you, thank you!!!!
Helped me a lot. My table did not have the 5/16 to put in leg/table to adjust forward/back. Had to screw mine to. A lot of the screws are different. The video definitely helped me.
Thank you! I recently purchased the DDL-8100 and couldn't find any assembly instruction - then someone told me that its essentially the same machine as the DDL 8700 and I found this video to be incredibly helpful!
You are welcome!
I’m confused on what screw was used to mount the legs to the table. Was it the ones with the hexagonal head???
I’m not sure to height bolts are long enough
THANK YOU!!!! That was superb.
Glad you enjoyed it!
Thank you for this incredible video. I will assemble mine tomorrow .
Glad it helped
Thank you so much.
Awesome instructions
Thank you so much for this excellent video!!!
You're very welcome!
Merci pour votre tuto, cela m'a été vraiment utile, vous travaillez bien 💙
Wonderful video
Thanks for the video instruction!The only one which is awesome and clear
Glad it helped!
Wow this is very good 🎉🎉🎉🎉🎉
Thanks guys
Our pleasure!
Thanks works like a champ
Glad it helped!
You are the best
You are so helpful thank u so much
You are so welcome!
Thanks
Very helpful video.. the only thing I did different is was I drilled the holes for light and thread stand before putting the pan and head on. That way you don't get sawdust in the oil pan.
Great tip!
Wow good 👍
thank u
Superb video. If I buy one it will be from you. Thanks
Thank you for making this video. It helped to set up machine without making any mistake. 👍👍👍
Thank you for your tutorial to assembly the yarn:)
I get so confused to use big yarn the size is 20/3. When i use it, it can't work properly. Soon i will try small yarn..
I want mine assembled!
I like it very nic
Good mashing
Thanks for the video. I am assembling a juke 8700 but I didn't find the hand wheel screws in the box, can you tell me which number is it, so I can find out how to get it?
Thank you so much, you may have saved our marriage. 🙏😁
Ha! We do what we can
👍thanks
Welcome 👍
Great video. I wish I came across this before putting my machine together. I am having trouble tightening my belt. The higher the top screw on the motor is the looser the belt. How do I tighten the belt? Also the belt guard makes rumbling noise when I press on the foot petal.
czcams.com/video/4WkjA-GmfxY/video.html About 6:14 in shows how to attach the belt
Thanks for this very informative video! I’m thinking of getting a new sewing machine. Is this the procedure for Juki 5550 N?
Yes, it is!
This is pretty much the same for the 1181n correct? Mine just arrived today & this is by far the best video I have found. :)
Pretty much the same
What accessories does the Juki come with? Or does it all have to be ordered separately? Thank you
Great video. Doesn’t look to bad to assemble. Only one thing, a “lock” washer always goes to the nut, it serves no purpose on the bolt head side.
I believe my fuse is blown do you know where I can get a new one ? Do you have a video on replacing it?
Does this apply as well to take one apart for transport? How difficult is it to disassemble? (Not completely but enough to fit in a car)
I cannot thank you enough for this tutorial. Lifesaver. I would have been so lost. You were so patient and set a good pace in your explanations. God bless you and your team. However, I am still struggling with the knee pad because my machine came with the motor already attached to the table. so I am lost on where to attach the knee press/ Also mine did not come with the light fixture. Do I need to buy it?
Sorry for the slow response, but we don't sell them with the motor atttached. You can buy the light from us though!
Help, my table top didn't have any of these holes for table legs or motor where can I get this table top to go with the hardware
Please can you tell me how to fix thread stuck in bobbin and needle is broken.
I'll try to make a video. Can you send me a picture, so I can see how you did it?
Please help me that short tiny black screw popped off my ddl8700. But i can't figure out where it came from
Great video!! I have a trouble with a juki DDL 5530 but I perhaps this DDL 8700 works the same way. I think the knob to adjust the stitch length is broken or disrupted. When sewing forward the stitches are very small but when sewing in reverse the stitches have a normal length. Can I manually adjust the stitch length again?
It should
@@CutSew Yes thank you. But how can I manually adjust the stitch length when the knob does nothing anymore?
Hello can you tell me how long the table is?Thank you
The belt doesn’t move when I move the Hand-wheel Pulley. I did try tightening the motor but the Belt still doesn’t tense
Hello, what do you put the nails? What would happen if you do not put the nails
Showing how the bolt display you are doing it to fast
i can't get thes screws to tighten down for the cover . ! so frustrated. they just spin and spin like there's nothing to screw into
Budget Juki - Free
We were given by a friend a JUKI DDL-8700-7
Comes with a computer that is said not to be working (JUKI CP-160)
When the power switch to the machine is turned on the CP-160 turns on and everything seems to look ok. But when I push on the pedal nothing runs.
It does not show any error display or code to work with.
With your experience I was hoping for any advise as to where or what I should try?
I'll get with our mechanics & see what they say.
Where were you guys last week??? 😊
Filming this video unfortunately. Stay tuned. We're going to keep creating new videos!
Is there a way to remove the thread guide from the top. Mine popped and I need to replace it
there's quite a few, but it's probably just pushed in there and held with friction, so just pull it out.
Nice video where can One get such motor
www.cutsew.com/Electronic-Servo-Motor-High-speed-3450-RPM-110v-with-Speed-Control_p_6716.html
Can anyone tell me what the little metal piece with the cork is for?
lol did you ever find out? I been looking at so many videos trying to find out what it is for. No one says 😂
Update: after some googling… metal pieces are motor brush replacements and the cork thing is brake pad replacement for the motor.
I bought my Juki off Amazon. They sent me a 39 belt it seems to be too big I can't get it to have tension no matter what. Do I need a 38????
I just bought a 38 and it seems to fit well. I had a 40 before, and I had to adjust the swing-span of the motor all the way out.
I’m so confused on which screws you used to mount the legs to the table was it the hexagonal head screws ?? Please help!
It is the 5/16x 1” bolt with flat and lock washer.
How do u get the bolt with x on head into the underside of table to attach legs
Hello dear cutsew how much price juki ddl8700
I got one part that’s metal And cork I can’t figure out where it goes
Maybe you can help me. My sewing machine is going in the wrong direction after assembly. I don’t know how to fix it. Thank you.
Landu, I appologize for the slow response. Did you fix it? I've gotta ask my tech about this one!
If it’s a clutch motor, sometimes there is a switch to make them run in forward or reverse
Kang kui regane piro...
Hello! On which site to buy such a car, but that it was written Made in Japan?
Peanuts and Potatoes cured and canned in New Jersey
@@CutSew thank you!)))
Please reply from india
Need your help guys.. anybody here heard about JUKI MO1016 ?? it supposed to be an Overlock machine from Juki (Japan) but i cant find any detail of it from Juki website/ youtube or even from google.. nothing at all.. it seems that it doest exist? I am plannig to purchase used unit.. as i cant afford to buy a new one. And this is the one that i found in Market place.. but im afraid that i will not find any parts of it if something happend. And cant even find any instruction.. please help me guys..did juki stopped the production of it? Hows the part?will i able to find parts incase?🥺
Looked into it. Cannot find it.
Is the motor a JUKI part, or is it third party? If the latter, how can Juki warranty the machine when the motor isn't theirs?
The Juki warranty is for manufacturer defects on the Juki head only.
@@CutSew Thank you the response. It seems like this arrangement creates a grey area where Juki could claim that the machine head was damaged because of the motor, and maybe refuse warranty coverage. That's scary from a consumer's viewpoint, but I guess that's how these machines have been sold forever? Does Juki even make their own servo motor that a customer can purchase optionally?
I still can't fix my tension on the bottom.
I had issues with the tension from the belt. I had to buy a smaller belt. Mine came with a 39”. A 38” is a better fit for mine. Mine kept rubbing on the cover guard things.
Machine sawing juki 5550 okey terbaik sekali okey terbaik sekali okey terbaik sekali 😢😢😢😮😮😅😅😊😊😊😅😅😮😮😅😅😊😊
mas accion menos palabras
I want to buy one please helpe me
www.cutsew.com/Juki-DDL8700--ASSEMBLY-REQUIRED--57500_p_7009.html
Where are you located?
Our offices are in Atlanta, Georgia.
Dear
Good informative video
Sorry but
👇
your technician have poor technical knowledge.
Ex
He hole in table when installation is almost done
Why not hole before installing Head.
my table top doesn't have any holes for the legs to attach....>
Did you ever figure this out? Mine seems to be the same.
@@yourhealthkick no! and i've talked to others with the same problem =(
@@sam-co1oo I’ve actually had to predrill my hole. I set my machine up today
@@sam-co1oo Haven’t run my machine yet but so far in the installment everything seems good
Tagalog para maiintidihan ko
Dada Dam Kto
For me that is basic, I am looking for a video demonstration of how to assemble the machine head components