Honda Goldwing Water Pump Replacement | GL1100/1000
Vložit
- čas přidán 10. 09. 2024
- IN THIS EPISODE We remove the front transmission cover and replace the water pump and several o-rings while we are in there. The parts used are all listed below.
PARTS
Water pump (OEM) bit.ly/2lcaK39
Oil seal pt#:91207-580 bit.ly/2mRHVJI
O-ring #91333-KE5-003 bit.ly/2mr2vQG
O-ring #91345-580-000 bit.ly/2kNKzzl
O-ring #91305-KT7-003 bit.ly/2ms9j0p
O-ring #91312-371-013 bit.ly/2lbqELa
O-ring #91356-706-000 bit.ly/2lktOMv
O-ring 91305-426-003 (radiator bottom) bit.ly/2kRon7F
Water pump gasket bit.ly/2ll0Pbi
Transmission cover gasket bit.ly/2mt8ftd
Follow me on Instagram as I wrench and search for the next fun project (& money pit): @HooptieDoodle
#HooptieDoodle #KeepOnWrenching
Just bought my GL 1000, and you showed me why oil was coming out of the weep hole behind the pump, at the bottom of the trans cover. The PO put in a new water pump, but did not put the smaller o-ring in around the back of the pump. I'm really glad he missed that, bc I found he also failed to install the oil ferrule passage on the RHS of the engine that supplies oil to the filter, and new aluminum crush washers on the three bolts holding the pump to the case. Fortunately I bought the entire water pump gasket kit that came with all the o-rings, gaskets and washers, so no problemo. Back to the interwebs to find a replacement ferrule, but again, great work on this video!
ah, you are doing good things for that bike. Best of luck finding a ferrule. It will be great when you are done.
Man I’ve been try to get my gl1100 running for a year, just fired it up today running good but my water pump started leaking, thanks for the video, I wish they had one kit with the water pump and all those orings
Good luck !
@@HooptieDoodlewill this fix an oil leak from the weep hole?
Make sure with this engine you should be using blue coolant made for aluminum engines and rads that are silicate free other wise is can damage the engine and make the rad leak overtime with the silicates acting like sand paper to all the channels and tearing them away. The clymers manual as well as the honda manual reference this, cheers!
Well done, yes water and oil are now the 2 enemies of each other. You have solved this nicely again 👍👌
I hope it is solved! Thanks again
BTW, the things you call "tabs" are referred to in the shop manual as "dowel pins" (if they don't have fluid flowing through them) or "collars." Just in case you wanted to know 😀
Thanks a lot for this video. You made this look very easy. I have next to no mechanical experience on my gl1200 and think I need to replace the water pump. Will follow this video step by step with a buddy when I do it. Thanks again, this looks like it'll be a fun project to get into!
Best of luck! There are a number of steps, but it's totally feasible. AND totally worth it! At least on mine, it made a HUGE difference, cause the seals were TOAST. For me the flushing of the oil was the most annoying part as I didn't know when it would end...
I'm building a gl1000 for a customer
Excellent channel sir.
I'll be watching ALL of your videos
Good luck on the build👍💪
Thank you! Well done! Sorry about the rain.
Thanks for Your video. Im just gonna do my pump today.
Thanks man! You're the best!!
Excellent video. Thank you. 😊
Thank you guys! This is a great video and taking some time to show the parts needed. Big 👍
Glad you liked it!👍🤙
thank you very much for this video. I purchased an 83 goldwing aspencade where the previous owner had removed the water pump as you did, but had not replaced it. I had worried if the bike would be worth fixing or to take the parts off it and sell them, scrapping the rest. the engine only has 68,000 miles on it. After watching this video i think i may atl east put in a new pump and put the parts on to see if it will run. Thanks again. The wiring is a mess, but if the engine runs i may put it in a small cabin boat project i am getting ready to start on.
Cabin boat with Goldwing engine - awesome👍😀👍
@@HooptieDoodle ill send u pics once i am done
@@bennynash6655 excellent 👏.
Just an FYI, the reason for no torque specs on the water pump assembly housing is because the original fasteners were large screw heads not hex head fasteners. Really good video…..
Those little "tabs" are called Locater Pins. Nice video!
Great video. This is going to help me so much. I was struggling a little with my GL 1000 project water pump, but this cleared up my questions. Hopefully I get get the motor done now and back in the frame for gas tank mock up.👍
NICE! Hope it works out and you get that beast fired up soon
Thanks
Bro reminds me of Moby the robot from school 😂😂
I changed the water pump watching this video and with the maintenance manual in hand but oil is leaking from the small hole under the cover :(, does anyone have any advice?
thank you for the video
Thanks for this video was a giant help and was explained really well. Thanks again. Ya got any vids for carbs on the same bike.
Thanks man, but no carb videos. Luckily mine had not sat for very long and were in good order. I may be doing a re-jet, but that is down the road.
Thank you so much!
Will this fix an oil leek out of the weep hole?
@hooptiedoodle will this fix an oil leak from the weep hole?
9:13 this video is awesome but bro that bearing is crooked as heck
I have a Honda Goldwing GL1100 Interstate, i have a big problem, when i ride in
uphill roads, the motor is overhead too much, but i don't what ocurre, the thermostat, the water pump, the oil, etc, could you guide me what happened with my motorcycle....?
Check to make sure your fan is. Oming on..the thermal switch fails causing fan to not run. Easy fix is to bypass switch and run power and a ground to fan on a togglw switch. Or replace thermal switch. Ive road my gl1100 for 10 years on a toggle.
Hi,can you please tell me where I can buy all the spares.I have GL 1000 and my water pump bearing came short.thanks
There are links in the description of the video 👍
Hey quick ?? Did this solve your issue ?? I don't believe the head gaskets are bad on my 82, cause it runs and don't smoke to holy hell... I can get all the parts for about $120... But most people I talk to say the water pump is usually the culprit on these goldwings....
Yeah, the water pump was my problem. Oil looks like oil now, ya-hoo! New water pumps aren't cheap though. I had a good extra one around, but the other oem gaskets and seals I bought were less than $30
Tried 2 after market pumps. Both leak had apart 4 times. . I think the pump housing was to big ,replace it with oem slide right in no leaks
i was going to say but never mind, hey do ya think ya could do new clutch without pulling motor?
The clutch can be removed with the engine in the bike. You have to remove the rear wheel and exhaust, but it can be done. I am hoping that I don't have to do that any time soon (fingers crossed).
@@HooptieDoodle yeah that is what i thought too. so good luck my Rat Ride is running rough but it's a rat who cares. haha
Como consigo repuestos
been watching some of this Build!! Haven't quite found yet in the videos but what exhaust is that? would like the same for mine!
czcams.com/video/-Z2WqZsC5uw/video.html
Thank you!! Will be starting a goldwing build myself soon.