VanMoof S3/X3 Smart module dead 💀, manually charge the battery inside the module
Vložit
- čas přidán 29. 08. 2024
- Hello guys thanks for watching..
Also I'm trying to make a channel regarding problems like this
if you have any suggestions or challenges for me I'm happy to try solving them :)
if my videos help your business and you will like to help back with a donation or simply get in touch please do so on razspareparts@gmail.com (PayPal) also don't hesitate to contact us
Razspareparts UK
this is the full list of errors to your S3/X3 Bike 🚲
Here are the battery-related
errors for the VanMoof S3:
1. BAT SCP: Short circuit
protection (main battery
related)
2. BAT_ MOTP: Mosfet over
temperature protection (main
battery related)
3. BAT_PDSCP: Pre discharge
short circuit protection (main
battery related)
4.BAT_PDOCP: Pre discharge
overload circuit protection
(main battery related)
5. BAT_UVP2: Under voltage
protection 2 (main battery
related) (try charging for a
longer period, could solve
issue)
6. BAT_UVP1: Under voltage
protection 1 (main battery
related)
7. BAT_ OVP2: Over voltage
protection 2 (main battery
related)
8. BAT_OVP1: Over voltage
protection 1 (main battery
8. BAT_OVP1: Over voltage
protection 1 (main battery
related)
9. BAT_COCP1: Charge over
current protection 1 (main
battery related)
10. BAT COCP2: Charge over
current protection 2 (main
battery related)
11. BAT DOCP2: Discharge
Over current protection 2 (main
battery related)
12. BAT DOCP1: Discharge
Over curent protection 1 (main
battery related)
13. BAT_CUTP: Charge under
temperature protection (main
battery related) (it's too cold to
charge)
14. BAT COTP: Charge over
temperature protection (main
battery related) (it's too warm
to charge)
15. BAT DUTP: Discharge
under temperature protection
(main battery related) (it's too
cold to discharge)
16. BAT DOTP: Discharge over
temperature protection (main
battery related) (it's too hot to
discharge)
17. BATFP: Permnanent fail
(fuse burn) (main battery
related) (likely socket short
circuit)
18. Error 17:
BATTERY_ NO_DSG - Could
not set discharge mode (main
battery related)
19. Error 18:
BATTERY_MISSING - Signal
bat_key_in is low (main battery
related) (battery not
recognized, also the error you
get when no battery is present)
20. Error 19:
BATTERY COMMUNICATION
- Modbus battery (main battery
related)
21. Error 20:
- BMS
seems to shutdown (main
battery related)
22. Error 21:
NO_ CHARGE_CURRENT
Charging state but no current
reported (main battery related)
23. Error22
SSP TI Motor chip (module
related)
24. Error 23:
BLE chip (module related)
(Bluetooth chip)
25. Error 24: OAD _ABORT
Transfer from app aborted
(Module related) (Upload was
aborted?)
26. Error 25: OAD_ CRC -
Transferred image crc error
(Module related)
27. Error 26:
- OAD file transfer took too
long (Module related)
28. Error 27: OAD_PACK - No
or invalid file in pack (Module
related)
29. Error 28: ICF_TIMEOUT -
Timeout during flash
programming (Module related)
HEADER -
30. Error 29: ICF
Header not found (Module
related)
31. Error 30: \CF_ NO_FILES -
No files in pack (Module
related)
32. Error 31: ICF ERASE -
Flash erase error (Module
related)
33. Error 32: ICF WRITE -
Flash write error (Module
related)
34. Error 33: ICF CRC - File in
pack has CRC error (Module
related)
35. Error 34 -
Programming of the motor
Controller failed
36. Error 35:
PGM_BATTERYWARE -
Programming of the BMS
Controller failed
37. Error 36:
PGM_SHIFTERWARE -
Programming of the shifter
Controller failed
38. Error 37: PGM_BLEWARE -
Programming of the BLE
Controller failed
39. Error 38: -
STVC3115 read error, LiPo
might be missing (Module
related) (check if battery
m o io hor)
40. Error 39:
READ_LIGHT
_SENSOR
CM3232 12C read u - Kick-
Lock coil not detected
44. Error 43:
SHIFTER_NOT_IN_GEAR -
After 10 tries, gear has not
been reached
45. Error 44:
SHIFTER
COMMUNICATION -
Modbus Shifter (Shifter not
recognized) (Plug in tester
Shifter)
46. Error 45:
MOTOR MOTOR CABLE -
Bit2/NTC motor cable not
Connected (Motor not
recognized)
47. Error 46:
MOTOR MOTOR_OVER CURRENT
- DRV8301 over temperature
(bit6)
48. Error 48:
MOTOR CONTROLLER_ERROR
- Error in user parameters
(bit8) (replace motor)
49. Error 49:
MOTOR CURRENT_ERR -
Current offset calculation +-
from default value 1.0
50. Error 50:
MOTOR_VOLTAGE_ERR -
Voltage offset calculation
+*from Vbat/2 or Vbat
51. Error 51:
MOTOR_ DERATING - Max
current limited due to high
temp
52. Error 52:
MOTOR TORQUE_SENSOR FAIL
- Torque sensor failed, only if
sensor required
53. Error 53:
MOTOR NOT READY - Motor
not ready during motor test or
error
54. Error 54: NO SIMCARD -
SIM card not present (Module
related) (SIM not recognized)
55. Error 55: 12C3_FAIL -
Started with l2C error on bus 3
56. Error 56: CCID_SIMCARD -
SIM card wrong CCID
(VanMoof) number
57. Error 57: READ_SIMCARD -
SIM card is detected but no
communication (Module
related) (Check ICCD number
in BO)
58. Error 58: GSM_MODEM -
Modem startup sequence
failed (Module related) (often
gone after reset)
60. Error 60: FACTORY_MODE
- Display 60 when factory
hope it helps ☺️
I can't drink coffee anymore. Hopefully I'll be able to fix it!
Hi cool work. Regarding the error codes: Err 48 Motor controller Error --> you suggest replacing the motor. Regarding to the community and my certified VM bike workshop it is a problem of communication between motor and cartridge caused by faulty or broken cables. Solution should be changing the whole socket/hairness which is a royal PITA.
Hello Raz, thank you for the video. I added a new battery (3.7v lipo), but when connected to charger, no charge sign. When I disconnect the charger, I get flashing skull, but then when I reconnect charger that goes away and no charge sign. Does this mean the battery is not charged enough? Thank you
Thank you Raz for your video. How can I replace the battery in the module unit ?
That video is made by vanmoof try on CZcams Search
Hi great video. Again. Can you recommend a replacement battery for cartridge? The one you just recharged in this video? Thank a lot in advance! L.
Can you please share the link to buy new battery ?
Hallo! Super Video❗️What can I do when I see error 23?
I opened my cartridge because after taking it out it still emitted noise (I initially thought of selling the cartridge). Unfortunately I somehow managed to loosen the cable for the display from the main platine. Now I am somehow stuck to get it back in place. Any suggestions? Even maybe a little video how to replace the display because some of the lights in the display have already gone dead....Thanks in advance!
Hi Raz, how long does the battery power last when module not connecting to battery?
Could be a year or so without any problems
So basically, you need a variable dc power supply right?
Nice videos!! What do you think err 2 is? If i plug the charge cable i see the charge sign, but directly with err 2 code. And it seems to not charge fully. It stays about i think 80% or so? I hope you know something about this. Thnx
Error 2 I think is from the module... The big capacitors are shorted ... And is burning the main Fuse also from the battery
@@Razspareparts you think its to fix? Now i plugged the charge cable back in and it doesnt show err 2, but if i unolug the cable is shut down again. And i cant unlock the bike with the left button. If i start the app then its connecting. Its making me sick. The origin vanmoof store its on the corner where i live and you cant go there. Thats so irritating
Nicely done....do you do repairs? My battery is not charging😢
I do ... We talk after 27th I restart the repairs on these.. thanks 👍
Nice video. Thank you. would you be so kind to tell me the resistor value R71 at the bottom site of the controller, close to the 12 pin connector ? It exploded on the bord....
Is 100k ohm
@@Razspareparts Thank you!!!
Thanks for your great videos. Do you have recommendation when Bluetooth connection is not possible? Error 23.
Is the Bluetooth chip .... Also you might not have sound
@@Razspareparts yes. No sound also
@@leonidbogas4202 Is there a repair for this? I also have Err 23 and no sound.
How can I contact you Rez?
Razspareparts@gmail.com