How To Replace Hydraulic Surge Brake Actuator for Boat Trailer
Vložit
- čas přidán 24. 07. 2024
- Subscribe to @DGHD | Merch: debossgarage.com/merch
Watch next: • How To Engine Swap a S...
Surge Brake Actuator geni.us/actuator
Vacuum Bleeder geni.us/vacuumbleeder (affiliate)
0:00 Hydraulic compression hitch
1:01 Hitch removal
1:42 Pump bleeding brakes
3:43 Vacuum bleeding brakes
4:30 What's next
Follow us:
debossgarage.com
/ debossgarage
/ project.black.jack
/ debossgarage
/ debossgarage
Send stuff to Filthy Rich
411 Darling Rd, Canfield, ON Canada N0A 1C0
Merch, Tape Boss & Car Parts: debossgarage.com/store
Tools I use: www.amazon.com/shop/debossgarage
Show us your build project: debossgarage.com/nation
Help us make awesome stuff: debossgarage.com/membership
Watch More Deboss Garage:
bit.ly/DG_EngineSwaps
bit.ly/DG_AutoShows
bit.ly/DG_Reviews
bit.ly/DG_HowTos
bit.ly/DG_QuickTips
About:
From American Muscle to Classics to Diesels, DG will show you how to build, swap, and repair anything with a throttle.
*If the video was helpful, please give it a "thumbs up" and consider subscribing.*
Theme Song: "Travelin'" by SWIB ( / swib-1 ) CC BY-SA 3.0
All Songs: / deboss-tunes
Music License: share.epidemicsound.com/deboss (30-day free trial)
© Red Egg Entertainment | made in Canada
--
NO WARRANTIES: All of the information provided in this video is provided "AS-IS" and with NO WARRANTIES. No express or implied warranties of any type, including for example implied warranties of merchantability or fitness for a particular purpose, are made with respect to the information, or any use of the information, in this video. DEBOSS GARAGE ("DG") makes no representations and extends no warranties of any type as to the accuracy or completeness of any information or content of this video.
DISCLAIMER OF LIABILITY: DG specifically DISCLAIMS LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES and assumes no responsibility or liability for any loss or damage suffered by any person as a result of the use or misuse of any of the information or content in this video. DG recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. DG assumes or undertakes NO LIABILITY for any loss or damage suffered as a result of the use, misuse or reliance on the information and content of this video.
USE AT YOUR OWN RISK: This video is for informational purposes only. It is your responsibility to evaluate your own safety and physical condition, or that of your clients, and to independently determine whether to perform, use or adapt any of the information or content in this video. Any automotive repair and/or modification may result in injury. By voluntarily undertaking any task displayed in this video, you assume the risk of any resulting injury; your safety is the sole responsibility of the user and not DG. - Auta a dopravní prostředky
A quick tip from doing loads of motorbike brake - take the bleed nipple all the way out and put some teflon tape on the thread. This helps stop sucking air past the thread when vacuum bleeding, and also stops the nipple from rusting into the brakes into the future. Clear hoses and clear containers also make it easier to see if air bubbles are passing through too.
Came here to post the same, thanks for doing my job for me.
Finally a quality how-to on these surge brakes 👌
Thank you for this video I gain knowledge watching every one of your videos but this one will certainly come in handy. Thank you for the videos I watch them all on both changes keep up the great work.
Pretty simple system but a fella still learned a new trick. Thanks bad😊
AWESOME!! Great video
Got to love the surge brakes! If you're replacing the master, make sure that any orifice (the little brass thing on the outlet of the master cylinder) stays with the trailer... looks like your new actuator came with an orifice. Also, side-to-side is not always equal, you can see in the video that the line comes down one rail and tees near to one side... bleed the *other* side first, rear first. If you're having master problems chances are you're having slave problems too... open up those drums and make sure your slaves are free and not over-extended or rusted. Surge brakes don't self-adjust... you must manually adjust them using the pokey screwdriver method... go for light drag on all wheels. You can test them in a gravel drive... hit the brakes and see that all stop evenly, if one locks up more than the others loosen it.
So down here in Australia if we are building a off-road boat trailer for going adventureing we will use electric over hydraulic disk brakes and intentionally put the brake lines inside the frame to protect against sticks rocks ECT
I put surge brakes on my utility trailer when I built it. Trailer tires last longer and any vehicle can tow it, whether they have a brake controller or not. Most Uhaul trailers around here have surge brakes for the same reason.
in the UK its the only form of brakes we have for trailers, unless you are talking HGV trailers with air brakes. really dont see the point of 'trailer brake controllers'. seems like complexity for the sake of it, to me
@@petelattimer6808Trailers can have ABS, the trailer brakes can be activated separately from the vehicle brakes, trailer brakes can be set to come on an instant(microseconds) before the vehicle brakes for more stability. I can see good reasons. Most don't apply to tiny little utility trailers and such, but I can see good reasons.
I have the same trailer. Can you do a video on the how to service, replace wheel bearings?
slick
We have a handle on the master cylinder to bleed the brakes looks easier than a bit of 4x2
Great video! There is no issue with electric breaks on boat trailers. It is only 12 Volts DC, nothing is damaged or does not work just because they get submerged in water. The reality of water on electric breaks is nullified by the example of driving a trailer equip with electric breaks through the rain for hours. My boat trailer has electric breaks and has been in and out of the water many times both fresh and salt water, as well as driving it through the rain for hours at time.
Never knew there was such a thing as how that receiver moves to apply brakes to the trailer, COOL.
there is no other method in the UK for trailer brakes (unless you are looking at air braked HGV trailers). theyre either hydraulic like this, or rod operated. much more simple, and more reliable, if kept properly lubricated where its needed, than any electronic gizmo.
Boat content! Love it. It’s what got me into B is for Build. I was already a sub, but dang you made my weekend!
Not your fault but you just triggered so much PTSD of when a buddy and I replaced all 6 calipers on his triple axle boat trailer for his gazillion foot searay on the side of interstate 90 just east of coeur d'alene Idaho. haha man what a night that was.. 🤣
To bleed serge brake easer, instead of using a strap and a 2x4. remove the two bolts holding down the brackit on top that keeps the brake away in position and use a pipe on it and just pump the brake away tab and it will pump the brake easer then using the tung of the trailer...
Ps. love the videos watch all the time
What’s going on with Bronco? What’s going on with the Cerrado? What about the other projects?
Tip
Before wasting hours failing to vacuum bleed the breaks remove (and clean if necessary) the bleeder valves and wrap a bit of thread tape near the top of the valve so that it stops air from sucking past the threads. You can also try some rubber grease and an O ring
What no diesel in the boat?
When will we get an update on the V10 Mustang and the JuiceBox Bronco?
Just got one not too long ago. Juice box is done and a fine family ride. Scott built the v10 and had it installed and driving. Said he's too busy to worry about the upgrades he really wants to do. Stop being that guy that never learned how to do anything for himself. Go and look, put in a little effort before you cry for help. It'll change your life. Maybe learn how to cook a simple meal or two and stop living off fast food. Maybe watch and listen to the videos rather than ask questions that are answered usually in the first half of the video, cause even though you didn't this time, you're definitely that guy. Or don't, and wonder why she always cheats on you and your friends are always busy. Nobody is interested in taking care of a grown person. Nobody with good mental health, anyways.
Phil, bro, the fact is, I don’t have time to watch ever second of every video. Mostly cause I have an actual job and have my own engine swap I’m working on. I wasn’t crying about not having an update, I just genuinely wanted to know if they had canceled the v10 mustang or not. I was watching that project because I plan on doing a similar build in the future. I love this channel and I live Rich’s builds. Wasn’t expecting to get unloaded on by some random internet troll. Bro, I was just asking a simple question. If want CZcams drama, start following another type of channel, cause the rest of us here just love seeing cool builds. And if Rich himself sees this, love your channel man, I just simply didn’t already know that there was already an update on those builds
Brake
Out
Another
Thousand
0:22
Just wait 0:28
Broken
On
A
Trailer
Ahh just my opinion but 2 3/8 bolts holding your boat trailer?.
I'm sure their grade 8
Yeah was thinking the same lol.
All though @4:58 it looks like there are 4 bolts in it possibly.
my heavy duty dump trailer has a height adjustable hitch, i believe it’s only 2 1/2 bolts for a trailer that can weigh upwards of 16000 lbs
i doubt this boat and trailer weighs more than 6000 lbs
not saying your wrong for thinking that is sketch, but it’s not out of the ordinary
If you are pointing out the hitch bolts, listen to Rich again near the end
He said at the end of the video he was going into town to get bolts
👍👍👍👍👍
👍👍
😎👍
So everytime you back up this type of trailer hitch, the brakes are applied hard on the trailer?
Seems like thats what would happen.
Aspecially on uneven ground and or offroad..
no theres usually a lug you flip over the moving part to prevent it applying the brakes when reversing. in the UK there is no other method for trailer brakes, except HGV air brakes. they can be either hydraulic or rod operated.
I need to covert my trailer to hydraulic brakes
More fuel efficient????????
The two happiest days in a mans life...the day he buys his boat...and the day he sales it!
Those are only men that can’t work on their boat. Aftermarket parts are cheap and available take care of it and you will have a great time all summer. I currently have 3 boats I bounce between all summer long. I’m an average joe that likes taking the family on the water.
Not a fan of that style brake or coupler. The quick couplers don't have any adjustment so they are super noisey and good luck backing up a hill with surge brakes. I did my A test with surge brakes and had to make a gadget to block the brakes from working so that I didn't have to push the trailer backwards with the wheels locked.
There is usually a lockout device to keep brakes from actuating. But i’m sure some manufacturers never thought about having to back up uphill.
Surge brakes have a lockout when you put the tow vehicle in reverse. If yours locked up when backing up hill, then it wasn't working properly.
Someone’s not very bright, use the lockout lol
Don’t feel bad your not alone, a guy I know had his boat for a year and was looking at getting a new trailer because he hated backing it up, yet he asked me if I knew what the little pin that said “lock” on it was for lol
Hey Rich, I converted my boat trailer to electric twenty years ago,never had a problem, Just unplug them befor you back into the water. Reason I converted to electric was every time you backup you have to lock out the master cylinder and if you have to do a couple shots at getting it in each time you move forward or back down hill you have to lock it out again .Just a pain in the keester , talk to ya latter Gord
That depends on the hitch designs, some you have to remember to unlock it when you leave instead.
Hydrologic breaks are the best
First
Why don't you just switch to electric brakes and power the whole thing off of the Milwaukee 12 V under the driver seat? I saw a video of some clown powering his boat motor that way and the batteries on that episode of Deboss... I mean video, didn't corrode.