Is there a way to get to the bearing in this fan? mine started making noise, and I want to lubricate the bearing with some 3 in 1 oil, but I'm not sure if I can.
You have to connect the 3 pin to the 4pin it shows you a gap where it’s meant to fit! And go perfect it’s perfectly fine to connect both only bad if you connect it to wrong place on MOBO then connect the arrows on the ARGB , rbg together with the arrow keys in the same direction as shown in the video and add on fans! 👍 it’s super confusing and no helpful videos but don’t think too hard it’s simple just a lot of wired , take a deep breath 😮💨 and start with one wire at a time put aside the ARGB and work on the fan speed sync one after connect the ARGB side just remember to leave one on the end to connect to the MOBO✅
Question. Does one of each connection end up being left free hanging? I know this probably so simple but for some reason my brain can’t make sense of it and there is no videos on these that are any good😂
@@elianjim7817I'm trying to figure it out while typing this and yes you gotta leave them hanging Ive only figured that out for the rgb idk how to make the fan spin and what I have to connect it to😭
@@mre8ballgaming842 Is it working fine? Can i chain 4 ARGB connection to a single header? I have two ARGB headers and I'm planning to buy 7 fans (CPU Cooler included)-
These spin clockwise vs the standard counterclockwise fans but the direction of the airflow is still the same as the air comes out of the side with the sticker
today while putting mine together, I was having trouble as well. But I took a deep breathe lol and I realized it was the way I was holding the cable. It was making the pins tilt at an angle so I couldn't align the pins to the holes. I just had to hold the cable properly to where the pins weren't tilting upwards.
What I did was force the screws on the fans before putting them in the case so it will have grooves. It's tedious and that's what took me so long to install the fans.
WARNING.. Should’ve got the TL S12-S fans. These do not make perfect circles. The fan housing has 4 flat sides making the ARGB fans look squared. Completely throws off the look of my PC. Really disappointed. The fan sticker isn’t perfectly centered on any of the 6 fans I have, so they all look wobbly. If your fans are loud, check your bios and make sure fans are set to PWM and smart fan mode is checked.
My plugs don't look anything like that and they don't mate together without forcing them. Very disappointment in this product. Returning them as fast as I can.
Didn't even get screws with the fans and the box of fans had no instructions. Terrible.
Same
More fans like Tl S12 , I love the subtle look from ring / halo effect RGB fans.
Can I connect this fans with the Pc power supply? I have got a old motherboard. Thanks
Get a fan+rgb hub, you connect to SATA and mb.
Is there a way to get to the bearing in this fan? mine started making noise, and I want to lubricate the bearing with some 3 in 1 oil, but I'm not sure if I can.
You have to connect the 3 pin to the 4pin it shows you a gap where it’s meant to fit! And go perfect it’s perfectly fine to connect both only bad if you connect it to wrong place on MOBO then connect the arrows on the ARGB , rbg together with the arrow keys in the same direction as shown in the video and add on fans! 👍 it’s super confusing and no helpful videos but don’t think too hard it’s simple just a lot of wired , take a deep breath 😮💨 and start with one wire at a time put aside the ARGB and work on the fan speed sync one after connect the ARGB side just remember to leave one on the end to connect to the MOBO✅
Question. Does one of each connection end up being left free hanging? I know this probably so simple but for some reason my brain can’t make sense of it and there is no videos on these that are any good😂
@@blooprophet ik bro ts is so complicated but if im right i think one is always hanging did you figure it out?
@@elianjim7817I'm trying to figure it out while typing this and yes you gotta leave them hanging Ive only figured that out for the rgb idk how to make the fan spin and what I have to connect it to😭
Do I connect all of theme to the motherboard?
no only one, you connect the other with eachother in a serie
work with all mobos?
If you have 4 pin PWM and a 3 pin fan power connected it should.
Less than five in ARGB means i can daisy chain maximum 5 ARGB headers?
とっても参考になりました、ありがとうございました。
less or equal 3*?
I second this question
Equal is fine
Less is better
what if I have multiple and what do I do with the 4 pin one which comes with all and where will I plug it in?
can u daisy chain them?
Can I just choose one color for the lighting?
Yes in the drivers
Hi, are they noisy or not?
They're not too noisy....but they do seem to blow out pretty good
They're just fine, normal، nothing special, not too noisy but not too quiet either
Can I daisy chain 3 ARGB components into a single ARGB header on my mobo? (5V/3A) or is 3 gonna be too many for mobo to handle?
They state that they can support up to 3 within one link. Unless you have a super old mobo that needs to connect straight to the psu, should be fine.
thank you i was scared my led on the fans were broken but my cables just was false connected
How many should u daisy chain at once??...just 3 or can I do 6??
you can daisy chain both the fan connection and the argb connection, and you can do more than 3.
@@itsculturehero thanks I hooked up 6 to my pc without using a remote
@@mre8ballgaming842 Is it working fine? Can i chain 4 ARGB connection to a single header? I have two ARGB headers and I'm planning to buy 7 fans (CPU Cooler included)-
@@luisenrique3631i need to know too
@@luisenrique3631 Hello, did you buy the fans and use them that way? Did they work well?
Please make the TL k12 fans available in US and UAE..🙏
Huh,?
Thanks it's now on Amazon US
These aren’t the same connections that came with my fans… not sure where to plug in the 3 pin rgb cable
Me to. Did you figure it out?
@@dylanwiebe9897 you have to buy a RGB cable splitter
i thought this was a reverse fan blades? so the intake is when the fan is facing the blade side right?
These spin clockwise vs the standard counterclockwise fans but the direction of the airflow is still the same as the air comes out of the side with the sticker
@@NGreedia what sticker? like the 3 squares?
@@MightyWinz the info sticker is the side the air blows towards; you can always check this yourself by spinning the fan blades just a bit too
I can’t chain them together. The plugs do NOT connect???? I have pushed really hard and no go 😡
today while putting mine together, I was having trouble as well. But I took a deep breathe lol and I realized it was the way I was holding the cable. It was making the pins tilt at an angle so I couldn't align the pins to the holes. I just had to hold the cable properly to where the pins weren't tilting upwards.
Any app suggestions
softwere
?????????????
the screws provided dont even go into the fans? what do I do
I got that same issue rn and I’m returning this shit
What I did was force the screws on the fans before putting them in the case so it will have grooves. It's tedious and that's what took me so long to install the fans.
just improvise and make your own groove in the fan @@DankRice63
@@reedtkfilms7077 im havin the same issue rn, did you use a drill to make your own grooves. Im trying with a screwdriver but it aint enough
i did it with a screwdriver you just gotta really push hard @@shambolicc
WARNING.. Should’ve got the TL S12-S fans.
These do not make perfect circles. The fan housing has 4 flat sides making the ARGB fans look squared. Completely throws off the look of my PC. Really disappointed.
The fan sticker isn’t perfectly centered on any of the 6 fans I have, so they all look wobbly.
If your fans are loud, check your bios and make sure fans are set to PWM and smart fan mode is checked.
My plugs don't look anything like that and they don't mate together without forcing them. Very disappointment in this product. Returning them as fast as I can.
Mine didn't come with screws .____.
Same here. Any idea why?
@@ADawnblader idk. maybe they forgot, I had to buy other screws from Mercado Libre
My motherboard don’t got ant
Mine didn’t come with screws
L
my fans spin but argb doesnt work. i switch back to my old fans and argb still work so its not my motherboard. plz help
same thing
Did you check you were connecting the ARGB pins? Same thing happened to me and the reason was that I was just connecting the SYS_FAN cable
please make them available in india and make a music sync argb controller like the cool moon ones
they will work with the coolmon argb controller
Good video bru, u are the one! lets gou i love u i love u en español: La mama del benja