Self-levelling a floor - The Complete Guide
Vložit
- čas přidán 27. 07. 2018
- This video covers everything you need to know to pour self-levelling concrete and get a perfect finish on an uneven floor. It covers preparation, priming, mixing and pouring.
If you like this, you'll love Alex's 20-hour series teaching auto mechanics: • How a Car Works - 2020...
Why have you only uploaded 3 videos? Mate you're the best DIY explainer I've seen on CZcams!
Learn from my mistake! My son and I were pouring self levelling concrete over newly laid 3/4" plywood to lay down a concrete floor for a bathroom (to be tiled). I mixed and my son poured and spread. We needed 8 bags of cement. The problem was the cement started to set rather quickly, after about 15 minutes. So when my son poured freshly mixed concrete it refused to meld with the setting concrete and created lumps and dents. It took me half a day to grind off a big bump in the floor. Plus we had to do another corrective pour to fill an area that was lower (a big dent). This all could have been avoided if a) 1 mixed 2 bags at once in a larger container like a garbage can, mixing one bucket at a time was too slow, you need to have as much liquidy cement on the floor as possible 2) had we had a spiked roller to even the edges and 3) watched this video.
a friend of mine does all types of stone/tile work. He said if doing a large job with many bucket mixings, fill a bucket to the exact amount of water then drill a hole at the top level. you'll always have the correct amount of water to pour into mixing bucket.
Don Proctor that is such a good tip thanks
Genius!
@barkershill ??? .... you decide where to drill the hole based on the volume or weight of substance you wish to consistently measure. If you want 5 gallons or 2 litres you will fill the bucket to the level you want and then drill a hole at the fill line so any excess drips away. ....
Looking at the walls of that building , obviously they need pointing /rendering /painting . Would it not have been better to do that first and save messing up the new floor?
"Ribbed - but not for my pleasure" 😂🤣.Alex is clear, concise, informative, and funny. Great video.Thanks for posting.
Pretty good video - you covered just about everything, and clearly. A couple of points I'd add: #1 / I totally agree with the viewer who said you need a person mixing and helping with the carrying, so that the spreader can concentrate on that. You want as much as possible of the area to be runny at the same time. Once the compound starts to firm up, you will have lost the opportunity to achieve a truly level floor. YOU DON'T GET A SECOND CHANCE with this stuff. #2/ The spiked roller is almost essential if you want a really smooth and level finish. The spikes constantly break the surface tension, HUGELY aiding the leveling process. The difference between spiked rolling, and trowelling only, has to be experienced to be believed. I have tried both, and I will NEVER again do a project without the spiked roller. 3/ Spiked shoe bases again are highly recommended, if at all possible, as you can walk all over the job without leaving craters, that may or may not level up properly. #4 / Don't try to feather out any edges to a zero thickness, certainly if the leveller is intended to be your finished surface. Apart from that .. happy levelling. It's a great addition to the building game.
I didn't want to do do floor leveling but this guy got me fired up to do it. I love how he uses tools that us DIYers would grab from around the house, it makes it so much more relatable.
Dont have a anevrism when you check the prices on a colomix mixer 🤣
I love your no no-nonsense approach and your sense of humour. I think this is the best video for doing this on the web and no annoying music while you talk so you can hear what you're saying.
I was going to diy this job and came across 5 good youtube videos. Then i came across the best and truly complete one. I unsaved the earlier 5. One great video is all i need. Thank you.
A couple of things you might want to consider for priming. On a rough floor like the one in the video you should use a stiff bristle broom instead of a roller. The reason for this is that no matter how carefully you sweep a dusty concrete floor there will always be a residue. By using a broom and scrubbing in the primer you actually incorporate the dust into the primer instead of just rolling over it. It really makes a big difference in the bond strength.. Oh and a convenience tip - instead of pouring the primer directly on the floor, put it into a bug sprayer and spray onto the floor prior to brooming it in. It's neater and prevents puddling.
We used to sweep/ mop the dusty floor/sweep mop again if needed. Then use a thick nap roller. I like your ideas though! Every trick helps
@@drakevelazquez8728 many priming products reccomend to use a broom /brush on concrete not a roller
I like the broom idea. Great tip we're just getting into interior coatings
Yep . Always swirl it around pressing it to be sure it is sticking to the floor and not like dough on a floured rolling pin .
Tar on the dussty roof too.
@@gregorydahl Dirt and dust on anything....
I am just going to say, we should see more of you. There are probably 1000 things you can teach. Not just entire projects but also little things as well. This video was a great start to a channel.
Great job! Handy tip I’ve used before is getting a flat disc on a 9” grinder and just going over the floor for half an hour taking of the high bits, also with mixing I’ll normally add half a bag and give it a quick mix, then add a quarter, mix that then add what’s left, just means you’re not fighting a big lump in the middle, keep up the good work!!
I've always wondered why the primer was necessary. Your explanation is exemplary. Thank you. It makes total sense that an unprimed floor would sap the water too fast for a good cure. Exelent advice that got you a new sub!
I've never learned so much while having been flipped off at the same time. Thanks!
I've watched a ton of videos on a lot of things. You my friend are a great communicator and teacher. great job. can't say enough. !!
When a bloke tells you to calibrate your bucket, you know you're at the business end.
I agree. Thank you for the lesson.
@@GodsMistake whats a bloke?
To the point narrative, sharing typical on the job situational comedy is refreshing! That is why we love our jobs, we enjoy life as we do our task!
The best explanation on floor levelling I have seen thus far. Congratulations and thank you.
I've no plans to self level a floor yet still watched it from start to finish. Great detailed video.
Great video! You gave so much detail without boring the viewers. I feel much more confident about trying this myself now. Thanks
This geezer could be on TV no problem, great presenting style.
Hey....this was SUPER great. I always wondered how to use a self-levelling compound. This guy made it really easy to understand. Yet another reason to love the British!!! ...and I like some of the comments too. Helpful. Thx....R (From California!!!)
I encourage you to make more videos, the content is great even for entertainment. I sent this to my friends and they loved it, and they were not interested in leveling floors, till they watched it
You are a great teacher. This vid and the roof one are brilliant!
We get three guys on the job. One is the "Mixer" one is moving material and pouring it out and a third guy is there to clean as we go and make sure the other two guys have what they need at all times. This makes the process go quickly and in a clean and organized fashion. Nothing worse that getting too rushed, dirty or have to stop to clean or do anything but the job at hand. It is beautiful in the end!
Only 3? Bro I have 23,
One mixing
One cleaning
One pouring
One standing about texting
One shouting at women
One levelling
One checking its level
One checking the levelling guys sober
One checking the concrete is dry
One wetting concrete after
One making tea
One preparing food
One driving to shops for supplies
One checking milk level in tea
One checking the milk in coffee
And got a few more on general duties, I feel sorry for you only having 3
@@lildeanc Looks like the work will be done just right, with tea and food ready on time LOL
@@bohakasha🤣 you’d be suprised, somtimes more monkeys make more mess than one
Brilliant way of teaching, like a professor. Absolutely enjoyable.
If you use a piece of wire e.g. cut up a wire coat hanger and hang it over the internal edge of the bucket at the required level you are guaranteed the correct amount of liquid every time without having to search for the measure mark. This works particularly well for mixing coloured 2 pack mixes where you cannot see the measure marks. You just make 2 measure wires. One for part A and one for part B.
genius a small screw would work too
I loved this video-- it explained several technical issues that I did not understand after watching many other videos. For example, the reason to remove high spots prior to pouring (saves on material) and how different types of compounds are designed for different purposes (thickness, dry time, etc). Thanks! I now feel ready to pour! BN
What a fantastic no nonsense video! Great personality too not too dull and not too jokey. Just enough to peak your interest. Need to do more videos. Great content and quality. Would really fly.
Great video! I like the personality and humor as much as I like the instructional process. Excellent descriptions your video really informs while at the same time teaching how to do it properly. Great Job!!
In a different CZcams video on Self-levelling a floor, the only difference was the gentleman cut out a small section of the bucket so excess water would pour out. So he knew his workers were always adding an exact amount of water each and every time.
Which video?
Now they have ruined a bucket with a hole in it. Just get a stick with a highly visible marker.
@John Jones i think your right there , a bucket only costs a quid
17:00 I found myself in the kitchen that 1ml of water is equal of 1gramm exactly. So you can use a scale instead is much more efficient and accurate. 5.5 liter is 5500 ml are equal to 5500 grams or 5.5 kilos of water.
Trace a line in the bucket after that..
Pouring severals graduated glass of water into the bucket increase the error marge every time resulting in an innaccurate final reading.
Depending on the temperature of the water, may not be 1g exactly.
1000l Is equal 1000kg at 4 degrees c
this was an encouraging video to see that 1 person can do such a large room by themself. I have a 500 sqft room I am doing this weekend and have about 35 bags I will be doing. Pumped!
I love the detailed explanation, thank you
This is one of the best videos I have seen. Incredibly in depth and very well explained. Plus, for your American friends (me) I truly appreciate the conversion from Meters to Feet etc.
Very well presented, making it so easy to follow.
If not already you should be on TV
This is the best video I have ever seen .... The editing is superb, the explanations sooooo detailed. So consice. Loooove this guy! (y)
Well done and thank you. Your video is better than most professional sales videos. Thumbs up for your cameraman/woman too! Great job!
Excellent video. Explained so much more than other videos that were just selling their product. Loved your talking.
What an excellent detailed explanation. Much appreciated. You are a fantastic teacher creating an "I can do it as well feeling"...... Thank you so much.
So much knowledge in just one video, you should have 4.5m subs instead of 4.5k
Absolutely perfick. Am retired now but did exactly as you advised except for one thing. In Australia we can buy a “walking trowel” specifically for this work. Means you pour as you did by walking pouring the bucket along the perimeter of room and then whilst standing the trowel which is on a broom handle 400mm wide fixed at about 30 degrees on long side and you gently ‘sweep it” back and forth. Great for around toilet pedestals into corners etc. the trowel has the leading edge at right angle to the short sides but rounded on the top clean edge. Was able to do large areas without bending or soiling knees.
What can 685 grouches find wrong with this detailed, complete and well presented video?
Because this is not self-leveling how I imagine it. If you would like to install a floating floor, this would not be leveled enough... You would have to make much more self-leveling concrete/mixture (in much more bigger container) and pour it at once... Not mentioning that by this way of self-leveling you could have problems with furniture (table, wardrobe etc.), while the floor would not be leveled perfectly.
@@MrTomasekk A "floating floor" by definition is a floor (usually a slab topping) that isn't physically connected to the subfloor structure. An application is to reduce impact sound transmission. If the objective is to achieve a level floor surface over a substrate that deviates from level by in the order of 15mm then a "self levelling" i.e. floor that can flow to form a level surface, is what is being very well demonstrated in this video. If you need to level a floor that's more significantly out of level, a different method can be used. Over an existing concrete floor a concrete topping can be applied by scrabbling the existing surface to form a key, priming with a cement and water mix, pouring, compacting and levelling the floor. If the concrete surface is to achieve its intended strength then covering it with plastic sheet (or keeping it wet) will retain the water required for hydration of the cement in the mix for a sufficient time.
If you have a short paddle mixer and a lot to mix, build a sturdy platform for the bucket to sit on so that you are standing upright, It will save a lot backache.
Also, mixers can take a few seconds to stop so a hanger to suspend the mixer on between uses saves valuable time.
The cable tends to wrap around spindle easily as it doesn't stop spinning immediately so I extend the flexible grommet to help keep the cable away from the moving parts.
I have been a plumber for 15 years, Doing this for the first time tomorrow and watching this has given my the confidence I needed! Great video I am going to subscribe for sure. Thanks a lot!
How'd it go?
@@May4thbwithu it went ok... ive done it quite alot since this comment and learnt from a few mistakes haha.
Love the clever trick of white glossing the bucket, I'd never even realised my black buckets had a measurement in them! Also calibrating is equally good idea, thank you. Now I need a spiky roller with long handle before I start. Great video, please make more
"Ribbed on the inside, which is not for my pleasure" HAHAHAHAHAHAHAHA
Excellent thank you for sharing the problems that occurred at the end something to look towards avoiding!!!
Good intro for DIY enthusiasts. I do thousands of m2 of this stuff every year. Problem is your mixing prep took too long and that spike roller had to go on straight away after pulling. The air bubbles MUST be removed failing which you get a weak floor. Depending on ambient temperature some products have 6 - 10 minutes working time to join to the next mix. Which is not alot of time.
Very well-made video! Just about to do a room now. Feel fairly confident after watching this. Thank you.
Very helpful. I might be tempted to blowtorch those threads off before starting.
I was thinking to use a garden strimmer but a blowtorch would be great too.
Bro your videos are great. "Just calibrate your bucket " ...lol. First time I heard that, but you're 100% correct.
Great video for carpenter like myself, I'm about to tackle about 300 sqft of horrible new concrete deck that was poured a month ago. I've used this stuff a few times before but definitely learned some great tips.
Many thanks.
I liked this for the primer dry floor water sucking explanation.
The explanation on concrete curing "drying" was very well said. This is why you can't leave concrete in a mixer or bucket and simple add more water. It will cure under water. The mix might be different but it will still get hard. Also, this is why concrete is covered with plastic to strengthen it, if the air is very dry. Rain doesn't effect concrete aside from physically disturbing the surface.
This is a really excellent video ! Straightforward presentation style; just the facts; logical flow of information; things to avoid doing; safety warning. Excellent ! Can't believe this channel only has 2000 subscribers. It should have at least 100x that ! New subscriber here. Greetings from Prague, CZ
Good lesson on levelling concrete.
Very informative, thank you!
I learned a ton about self leveling. Thank you!
Nice job! Great breakdown of what self leveling underlayment is too! Thx
!udgh
what just happened? I m not a DIY man but that was one of the best videos Ive ever watched. brillant stuff dude. keep it up. I just learnt somethign!
Good video apart from no mention of moisture content. You MUST measure the moisture before you start even on new floors. Damp will blow the screed and any floor coverings. Various products are available to overcome any issues
I am in the middle of doing a large workshop. The builder made a mess of the floor. The finish. It is bad enough that I am going to have to use self leveling cement to fix this. It is divided up into 12X4 meter cells. The concrete is Mpa30 x 150mm thick with reinforced steel mesh. It has been float finished. I have done a lot of renovation work. But I have never used self leveling compound.This is the Best explanation of how to do this I have so far come across on CZcams. May you, and your tribe prosper mightily. Kind regards, and greetings from Africa.
Big job. I remember seeing a truck which mixed self leveller for a second floor. They had squeezecrete to pump.
Well done on your job. That's not easy work and lots of cleaning. I had to level on a smooth troweled concrete floor.
Since it was a shop on lease.
I spoke with an industrial chemist and followed his advice. You can get fine silica sand and mix with cement and also use a screedbond which is a latex synthetic rubberised emulsion system. Say for instance a bonding agent and mixed 50% with water.
I mixed at 2.8 cement with silica sand.
I used a feathering edge which worked quiet well was pleasing. The area I needed to cover was not as big as what you did. However I achieved pleasing results.
Hopefully it hasn't laminated. The problem with self leveller is it is a liquid type of application and it only self levels the area you cover before the liquid hardens.
Brilliant video - exactly what I needed to tackle a friend's bathroom. "This bucket is ribbed - and it's not for my pleasure..." LOL
Genuinely the best DIY video I've seen. cheers so much!
I'm here just for the intro graphic, that was sick.
Great video, when I am mixing 21 bags worth I get them open ready and a large water tub full of water saves wasting time 👌👍
Great technique tx!
I watch heaps of these advice types of videos on CZcams as I enjoy doing some work myself, about to raise my kitchen floor 20mm and wanted some tips on using self leveling mix, I came across this video and found it to be about the best one I've seen. Awesome tips well presented, thanks heaps from Melbourne.
Peter Hushin why are you raising your floors that much?
@@mikeo6525 I installed wooden floors and with the 10mm ply and then the wooden planks it took to gap to between 20 - 25mm difference
Peter Hushin that makes sense. Consider raising your other floors with plywood. It will be cheaper and easier plus plywood will be more structurally stable compared to a cement leveler
We usually burn the fibers off with either a weed torch or a small propane torch-much easier than cutting them, just make sure there is nothing flammable around if you do burn. After burning sweep or vacuum up ashes.
Everything I wanted to learn from a very experienced This You Tube Channel is destined for greatness. Excellent presentation, excellent content, very encouraging to DIYers, v.g. Presentation style , excellent professional video style and sound quality. GREAT instruction. Thank you 🙏
One of the best informative videos I’ve ever seen. Thorough concise and extremely well explained! Thank you very much
The white gloss on the black bucket has earned a sub straight away.
Absolutely superb video. Very entertaining and learned a lot in the process. Thanks so much.
Thanks for the video 👍🏼
Cracking video and explanation, thank you.
So many gems hidden in your casual talking
This is a really great video. I'm preparing to level a kitchen floor in an old Victorian house and I've been looking at a load of levelling videos trying to pick up different tips. This covers them all and more. Every tip is well explained. I particularly liked the bucket calibration! I never even considered my bucket could be 1/2 ltr out which could make the difference between a good and bad pour. Love the gloss paint trick too. The amount of times I've been maneouvering a bucket trying to see where the damn calibration markers are! Brilliant job. Fingers crossed my floor comes out as good as this...
Good discussion on the importance of primer and priming.
Going to do the floor in my garage and this video certainly helps, quality thorough video, thank you
Nice heavy duty trolly/dolly. Can I find one like that in an industrial supply house?
Propane torch for the fibers when you are prepping. And a cheap plastic bug sprayer to apply the primer then back roll (also how I apply sealants to the finished concrete) . My 2 cents.
Money well spent...
What type of sealants do you ad?
Great guide clear instructions cant believe it only has 3 videos on the channel
I could watch this guy all day. He's like the Bear Grylls of construction.
No. He’s the Gordon Ramsey of construction!
I’m having flashbacks to when I did my own floor. 40 bags, alone, only following the instructions on the bag 😂 I got a good result in the end, but it is not as easy as this guy makes it look! The one thing I learned is that I will never do it alone again. It would be really really helpful to have someone mixing for you whilst you only have to worry about spreading it!
Nice job though and I like the effect the roller gave. A good non slip finish for a shed 👍
If you are working fast enough, and that means having enough people for the size of the job, you won't end up with the spiked roller 'dimples'.
You are a great instructor, thank you for sharing your knowledge with us.
Great video with lots of helpful content, and clever (cute) production too. Tomorrow I’ll be working on a small job. I’ll start by trying to grind down the high spot and then calibrate and follow the math. Thank you from Canada. Metric, for the love of Pete!
If your paddles are too short try putting the bucket on something the right height.
Just found ur channel. And wow. I have watched a whole lot of videos. some ok some good but this was great. Well explained. Thank you. Needed this. Redoing a horrible basement bathroom.
Thank you for such a comprehensive video. I am planning to use this as a finished floor in the small house I’ve built for myself. I had a beautiful mud floor in here before but had a bad fire and the fire hoses totally dissolved it. My question for you is can this self leveling concrete be colored and if so do you do it when you mix it or after it’s laid down? Could I stain it as they do with concrete floors?
Great tutorial. Thank you for sharing this with us.
Thanks now armed with the correct method my garage floor will finally be smooth and level.
Great video,and it has given me some confidence to try it myself. Thank you
House , garden , climate could bet that is somewhere in Italy , Spain , Portugal , Greece but the cement is made in Hungary. Excellent instructions , thanks.
so logic says it's in hungary. house has a definite east european vibe.
Great Vid Alex. Love painting a little gloss over the measurement guide :)
wow, good explanation while working techniques.
Great information! Thanks for the tips!
Just the perfect explainer video! Thanks mate.
this is a great educational video. i don't understand why the thumbs down. Too many trolls?
?
For me it was all going so well until I clapped eyes on the stippled floor finish in the last minute. Floor looks like it has a rash.
I think I’ve decided to do this in my small laundry room instead of tiling. I have a beautiful brand new hot water heater in there that I refuse to remove to do a floor. I may paint the floor and stencil. Still undecided on the painting. This video was very helpful!
Fantastic presenter. Deffo should be on TV!
Excellent overview! My 2 cents - In addition to the spiky-roller, it also helps to use a notched tiling trowel or notched-adhesive-spreader-on-a-long-broom-handle to really _spread_ the goop around to encourage it to self-level. Also, a squeegee with a long handle can help flattening the goop without straining your back :) BTW - add spacer-tape along the walls, if pouring more than 5mm thick :)
What’s spacer tape?
@@TomNouri It's basically an adhesive-backed foam tape - 3mm to 8mm thick. This prevents the poured floor touching the walls and potentially cracking due to slight movement of the wall.
Thanks for the info 👍🏼👍🏼👍🏼