synchronizing using L-SERIES ACTUATOR as speed control benzblogs
Vložit
- čas přidán 26. 03. 2022
- In this clip explain how to do a synchronizing using the linear actuator and the correct wiring for the speed control and configuration where you can learn lots of ideas for this
Really, great video. thanks for sharing.
Bless you sir
Maraming salamat Sa mga videos mo sir, malaking tulong talaga kayo sa mga gustong mag aral ng troubleshooting.
Bless u sir
Good info sir..
Thanks. I'm Iran
Hi
Nice!!!
Very nice and the same thing l do in Ghana
Bless u sir
Goood
What is the type biasing you using either sync/load share or remote speed set point
Bias always the type of control ang type of engine its can be pwm or analog
Do you apply droop to governor settings? Or isochronous
In my case we are not using droop for gov yes synchronuos
Why you dont using droop? Do you using isochronous mode? And what bias governor that you using?
Hello I'm Kumi from Ghana, please on a 12pin Delphi governor where do we pick the two wires to the governor on the controller
Just look in the ibternet you can search the commection from lseries
When Lseries connected with DSE, what would be the config settings on the DSE controller?
Nothing it same you do the configuration from your laeries
Hi
Good evening sir,
Sir this l series actuator direct will connect to deepsea controller or we need some separator controller???
Also it's connection diagram please...
This LSERIES sir if some wire are connected to your deepsea for your speed biasing for sync functionality
please explain configurations in lseries for 2 genset 60 hetz in syncro
If your are doing synchro using Lseries make sure you connection is correct you need to config the lseries in order to work at 60 hz and same as the module you need to config base on waht you need for synchro u need speed control for it from module to lseries
Good day
Bless u sir
Hello sir , how are you please where i can get the cable for actuator and program please
Sir you go to check online check lseries wire connector
How voltage center of l-series governor ? For sw1 value
Its always vary depend on the equivalent setpoint like 50 or 60 hz
If i set to 50 hz.. How about center voltage of sw1?
First thing you need to do is 1sw-3 sw2-2 for gov.this always vary on what your setpoint
L series with dse 3110 sycron diagram ?
Sir i dont have for 3110 is this for sync module?
Brother kindly upload video for 6 pin actuator
What kind of actuator can you name it the brand
It is same in shape to L series but instead of 12 pin, it was only 6 pin. Nothing was mentioned on it as it was full of dirt but i think it is used in perkins 1104 and 1106 generators
It was yellow in colour and same in design to L series actuator
@@fahadpirzada7684 i check this my be its old one but this 12 pin is can be use in 1104 series
Ok thanks a lot
May analogue input din bah yung governor niya sir?
Yes
Sir ano rating ng cross current compensation transformer na ginamit mo?
Dependi sir sa laki ng alternator mo
@@benzblogsVlogs sa genset na iyan sir anong rating ginamit mo?
Kailangan oa bang idownload yan na L-series
Yea po comg kailangan mong mag configure
Sir saan pwedeng makabili ng pang configuration wir mo sa L-series
Sir marami sa online pwedi ka makaorder
@@benzblogsVlogs sir pag order ko sa online anong tawag sa pang test mo sa -LSeries mo? Para maka order na ako sa online
Lseries tool ket
Woodward
@@benzblogsVlogs buenas noches. saludos! Es de mucha ayuda todos sus vídeo . Muy explícativos. Ahora tengo un problema ya que tengo 2 grupos electrógenos con gobernador L-serie y tengo que al encender el generador y darle carga no me compensa. Y me bajan las rpm. ahora quiero configurar la repuesta del mismo y me mide una contraseña si puede en ayudarme se lo agradecería.
Sir paano kita pede makachat may itatanong lang ako
m.me/ch/AbaxH-Wu4NQGcD2L/