This is a good guide, but you forgot to put the connector plate back on. Yeah the small screws are a pain, but if the phone gets a jolt from a drop the chances of one of those connectors coming loose is greater. So make sure you all watching put on that plate again. Also this phone is no longer water resistant. Some kits have gaskets that reseal the display to the frame.
Perhaps you just didn't watch the entire video? 25:19 I put the plate in and reminded people to do so. Also those adhesive kits do absolutely nothing for waterproofing and they are pointless.
How much editing do you do on screen removal? Also when you put the screws back in how do you get them to stay on the tip of the driver? I would get them going to hole the magnetic screwdriver would change alignment. Any suggestions there? 😊
I do no editing whatsoever that way you can see the mistakes if any are made. A lot of videos you see will be edited to make everything look perfect and seamless but they cut out vital information. As far as getting the screws to stay at the tip I just magnetize my bits or my screwdrivers. On my electric screwdriver I have a small magnet that stays attached to it. I hope that helps
I have been working on phones for over a decade and I've had people get water in their phone with or without the seal. Does it help, sort of because at the factory that adhesive is applied wet and hot and it molds to the frame and the screen whereas peeling it off of a piece of plastic even if heated it's just not the same. You will never get a waterproof phone not from the factory. I hope that helps
my friends and i in middle school installed halo into the whole schools network files and gave ourselves admin privileges so it basically could never be removed
It is not a 13. The cable on the battery was bent not allowing me to connect it properly that's why I suspected it was a different phone. If you watch the little further you would see that I didn't get the battery connected properly because it is an iPhone 12 Pro Max. IPhone 13 connects at the bottom of the L
This is a good guide, but you forgot to put the connector plate back on. Yeah the small screws are a pain, but if the phone gets a jolt from a drop the chances of one of those connectors coming loose is greater. So make sure you all watching put on that plate again. Also this phone is no longer water resistant. Some kits have gaskets that reseal the display to the frame.
Perhaps you just didn't watch the entire video? 25:19 I put the plate in and reminded people to do so. Also those adhesive kits do absolutely nothing for waterproofing and they are pointless.
How much editing do you do on screen removal? Also when you put the screws back in how do you get them to stay on the tip of the driver? I would get them going to hole the magnetic screwdriver would change alignment. Any suggestions there? 😊
I do no editing whatsoever that way you can see the mistakes if any are made. A lot of videos you see will be edited to make everything look perfect and seamless but they cut out vital information.
As far as getting the screws to stay at the tip I just magnetize my bits or my screwdrivers. On my electric screwdriver I have a small magnet that stays attached to it. I hope that helps
Can use third party battery?
Is a new adhesive unnecessary?
I have been working on phones for over a decade and I've had people get water in their phone with or without the seal. Does it help, sort of because at the factory that adhesive is applied wet and hot and it molds to the frame and the screen whereas peeling it off of a piece of plastic even if heated it's just not the same. You will never get a waterproof phone not from the factory. I hope that helps
Where can I get a battery to buy
Check mobile sentrix website
my friends and i in middle school installed halo into the whole schools network files and gave ourselves admin privileges so it basically could never be removed
What's the new battery health?
Can't see battery health with an aftermarket battery.
100%
@@tzuten use coconut battery on mac os
*My suction cup is so crappy. I cracked the screen. I will just take it to a shop!*
That's why I do what I do because it is a tedious and complicated job. I absolutely love it though
Be nice to know it was a 13 before i watch 10 mins of a video!
It is not a 13. The cable on the battery was bent not allowing me to connect it properly that's why I suspected it was a different phone. If you watch the little further you would see that I didn't get the battery connected properly because it is an iPhone 12 Pro Max. IPhone 13 connects at the bottom of the L