Common Fan Layout Mistakes You Might be Making with Your PC Build! PC airflow tips and tricks
Vložit
- čas přidán 19. 01. 2023
- In this video I'm talking about things to avoid when building your PC in terms of installing the fans. There's a logic to installing your fans for the best airflow. If you're a seasoned PC builder then this video might not be for you, but for beginners, sometimes it can be confusing.
There are certain things to keep in mind:
1 - Airflow through fans tends to go front-to-back. In other words, the front of the fan pulls the air and the back sucks. So you'd usually want to face intake fans facing outwards from the case and exhaust fans with their back to the vents.
2 - Hot air rises, so where possible it's best to put intake fans on the front and bottom of your case, then exhaust fans on the top and rear.
3 - Avoid putting intake and exhaust fans in close proximity. If you put intake fans on the front, but then exhaust fans on the side, right near by, all you're doing is making air flow into the case, then immediately out again. Not ideal.
4 - Watch out for falling into the trap of installing fans just so you can see the RGB. This is easy to do and I've done it too.
5 - Make sure you put intake fans on the bottom of your case if possible. If you set bottom ones to exhaust, then they'll be fighting the GPU fans that are trying to draw air through the graphics card to cool it. Most GPUs vent air out of the rear near the HDMI/DP connections. But there will also be some venting above as heat naturally dissipates.
Other related videos to watch:
Lian Li RGB not working? Here's the fix (SL120, AL120, Infinity fans and more) • Lian Li RGB not workin...
How to wire and connect Corsair RGB fans - tips for adding RGB fans to your case easily • How to wire and setup ...
How to improve the performance of your gaming PC - simple tips for more FPS • How to improve the per...
How to get more FPS with your Nvidia RTX GPU (better performance, less latency and more) • How to get more FPS wi...
I made some mistakes with this Lian Li Evo build • I made some mistakes w...
Lian Li Dynamic Evo build with Lian Li Infinity fans, Intel i9-12900K, NZXT Kraken Z73 and more
• Lian Li Dynamic Evo bu...
Lian Li Dynamic Mini Snow Edition build with air installation (features and how to) • Lian Li Dynamic Mini S...
Are you struggling to get your computer to stay cool? Do you keep hearing odd noises from your computer? It might be time to take a look at your PC fan setup. In this video, we're going to show you how to configure your PC fan and setup your PC airflow.
By following these simple tips, you can avoid some common mistakes when setting up your PC fan and airflow. We'll also give you some case airflow tips to help increase airflow in your PC case. Finally, we'll give you a look at some of the most common problems with PC airflow and how to solve them.
🏆Big thanks to my super awesome CZcams members:
SirSpawnsALot, Meatykeyboard, Beaster Bunny, JayShank007, Rawrr483, DStarastins, McFarty, Riggsy79, Chief Hao, Kraken Tortoise, Aaron Yarden, Paolo madamba, Space Cannons, Mike S, Kyle and Jason🏆
Want to send me things for videos or other reasons? Use this address:
The Provoked Prawn
PO Box 13277
MANNINGTREE
CO11 9BE
United Kingdom
🔫Sub to my gaming channel🔫 / @theprovokedprawnpews
Come check me out on Twitch - / provokedprawn
Join my Discord to keep up to date or ask questions / discord
Follow on Reddit / theprovokedprawn
Read this far? You're awesome. Smash those sub and like buttons!
📌 Support the channel:
😍 See the benefits of being a member here - / @theprovokedprawn
Get some merch - theprovokedprawn.com/
Check out my dedicated Amazon Storefront to see my current fave gear - www.amazon.com/shop/theprovok...
📸 Recorded with www.amazon.com/ideas/amzn1.ac...
Shure SM7B and GoXLR - • Shure SM7B and GoXLR M...
PLEASE NOTE
Affiliate links*:
Disclosure: Shopping links within the description of this video generate a commission at no extra cost to you. These are added for your convenience but other retailers are available. As an Amazon Associate I earn from qualifying purchases.
Products:
Products featured may also have been sent for free for review/testing purposes. Often these have to be returned by me, but not always. I endeavour to avoid bias in my videos wherever possible and try to give honest, subjective opinions. - Hry
Thanks for showing everyone how to do it the wrongiest way possible and not taking 1 sec to show us the right way 👌🏼
Thanks for this, most ppl assume everyone knows how fans should be mounted and stuff. This was very good for my nephew who is doing his first build now!
Yeah I think that people probably worry about covering beginner or basic things for fear of patronising or being criticised. Whereas I'm just trying to be helpful and assume nothing. 🤣
I watched several videos on this topic and yours was the first to really stick with me. Thanks for explaining like I'm 5!
THANK YOU for this video!! im planning on building my first pc this year and ive been doing my best to research everything as thoroughly as possible, but for some reason i just could never wrap my head around what anyone was actually talking about when it came to fan configurations and intake vs exhaust. using the smoke machine to visually show the airflow was so immensely helpful
Thanks Nivasti. Glad it helped!
Good info! I spent some time working g through this a few months ago.
Excellent video explaining fan setup and the importance of the correct fan orientation.
Thanks! 👍
Great video as always! One of my favorite youtubers for pc content!
Thanks Rob!
@@TheProvokedPrawn you're welcome!
haha. ive been building my PCs for 25 years and i have always over looked fan configs. but now that my new PC is gunna have RGB fans this issue has naturally come up and it was immensely helpful to learn which way the fans blow for optimizing my new setup. The hilarious thing is that my last rigs I just put the fans in any old ways and those rigs were amazing with no cooling issues and ran like beasts. But the more you know the better you can do... at least theoretically, haha!
Great video and well explained, well worth watching :)
Glad it was helpful! Hope you enjoyed enough to subscribe 🦐
If all else fails, I see a future for you as an airline attendant, thanks to all the directive hand gestures...lol! Great vid! I admit I had to stop and think about this when doing my build. It's tempting to defy logic in favor of aesthetics! The next big breakthrough...designing a fan where the shroud can be swapped or offer options for intake or exhaust that support your build and style. Appreciate what you do!
finally a video worth my time!
Thanks
Thanks Prawn, very helpful :)
Happy to help!
Excellent Video!
Hope it helps!
Cool Video...Thank you
Bad-dun-tsh
After you have the fans setup right, what Tom’s should the intakes and exhaust be set too? Also if you have a AIO?
"Helloooo this is the provoked prawn" was so zesty wth
Great video!
Thanks!
whats your toughts on all intake and one big 200mm fan at side of the case for exhaustion? or about having 2 exhaustions and put a button to activate the big daddy on the side whenver im playing high quality games? something between these lines :)
i am already doing this but the side fan is only a 120mm, ive lost 3º degrees celcius (gpu) with current this current setup having back and side exhausts
P.s my case its kinda of old and i dont mind of doing these kinda of projects... i didnt need it before i upgraded my gpu for a 30 series... i am already doing this but the
Damn u upload daily hard to keep up
I'm grinding 👍
What if i do the intake one to the front and one at the rear, and then two more at the top for the exhaust. Is it optimal?
I can put two intake at the bottom but since my case is small (more like cube shaped) and the gpu is big, the gap between the gpu and the bottom of the case is not that big but i still can fit the fan. Should i continue with this setup or try to do it like i mentioned above? Or do i just get a new case?
Thank you so much!!!!
You're welcome!
can i ask a question? is it normal for pc to vibrate much when 6 fans are spinning? i have the correct airflow, my only problem is its making loud fan noise and making my desk vibrate. when i turn off the 6 fans the pc are silence and no vibration
Are your case has rubber on feet? Maybe some of your fan is faulty or overpowered?
1.) Fan motor arms are the push side that blows air
2.) Be mindful of putting pull side of fans too close to any object from case or heatsink. Don’t make more noise by not paying attention to suction pull side not having enough gap.
Ive got that exact same chrome terminator skull on my desk :) Good timing on the video mate i bought a prebuilt pc a few months ago and im swapping case tomorrow. I bought the corsair 5000x rgb and some ql120 fans.
czcams.com/video/jvXCbny-Suw/video.html
@@TheProvokedPrawn thank you so much bro. Much appreciated
@@TheProvokedPrawn finally got around to swapping cases, had to wait ages for a single ql120 fan and wanted to thank you. It amazing and my temps are better with this case.
Thank alot mate i appreciate your help
I need help, so i have two intake fans on the front and i have one exhaust in the back. I decided to buy more fans and I want to install them on the top, should they be intake or exhaust?
I have a question : what if I use one intake from top of RAM, two intake from below and one from side? For exhaust I propably use PSU and direct air from CPU tower cooler will setup optimal? Or I gonna kill my PSU (and CPU?) due hot air from cooler? Perhaps I should make intake for PSU on top.
Oh yeah my case was old orange cameroon I was planing to mod this case for addional fan one on top and two below.
I knew most of this but it's still good for a review.
👍
If my case only has holes on one side, the bottom and the back and I can only install one fan in the back, I should make it an exhaust, right?
What do you think about: Intake: 3x 120s front, 2x 120s bottom. Exhaust: 1x 120 back, 2x 140 top
I reside in the 1%, I have 1 140mm pushing over my VRMs, and 3 140mm pushing into 420mm rad, 3 140mm pulling from rad. If this sounds odd just look at a Tt Core P3 frame and you'd get it. Great topic for new builders...or confused ones 😉
is 2 120mm side intake and 3 120mm front intake optimal? my cpu is air cooled
To be fair, wouldn't the entire test be different if you put the side panel on the case? Regardless of your fan config, if you have no side panel, your airflow will suck, right? Lol cause then there's no pressurization inside the case.
Front and bottom to intake and top and rear exhaust. Sounds easy enough
How do side intake fans interact with the front intake fans? Do they help? Or do they create a turbulence zone that impairs the airflow coming from the front?
I need to know this as well
Would you recommend Noctua fans over Lian Li fans? Performance preference, leaving out the Aesthetics SL120V2 vs NF-A12x25
Performance wise all the serious reviewers would say noctua is superior
what is the PC Case used in this Video? Please let me know, it help build the new PC. My existing Case has a bottom fan and is beneath the PSU. Is it a wise choice to add a fan as intake towards MB, please let me know. thank you.
So for gaming pc should i go for positive placement or neutral?
Anyway you would recommend 9 fan set up for the O11 Vision by lian li
I think it's not so clear. I have an inverted case where the gpu is above the cpu. My case allows me to install 1x 120mm front, 2x 120mm on top and 1x 120mm rear fan.
My 3 scenarios i thought for my situation are:
1. front and rear intake. Top exhaust.
2. front and top intake. Rear exhaust.
3. front intake. Rear and top exhaust.
Which of the 3 versions would be best for my situation with the inverted case?
I would think its either scenario 1 or 2 for me but i am not sure.
You mentioned gpu fans and exhaust fans fighting each other. That would be true with top exhaust for me because my gpu is mounted under the top fans with gpu fan facing upwards.
Thx for answers
What if you have a radiator on the top of the case? I have the phanteks pro case and really the only place to exhaust it out of the back. Should I have top front and bottom pulling air in and just exhaust out the back?
If your radiator is mounted to the top of the case have the fans blow the air out of the case from the top and all other fans blowing cool air in.
Do you recommend Peerless Assassin 120SE air cooler or a Kraken elite NZXT AIO for a pc?
I've only tried the Kraken. But I love it
I'd be interested in the temperature differences between the correct fans vs incorrectly placing then 🤔
I have a question, I hope this gets answered by anyone if possible.
I have a coolman robin 2 mini (you can call it a poor man's lian li o11 mini, if im correct)
I run an i5 10400 and have 6 fans (3 bottom intakes, 3 top outtakes).
I was told that I dont need to have an AIO with my CPU so I stuck with an air cooler (blowing directly onto the cpu). Is that good? I was planning on adding 2 more intake fans on the side (beside the mobo), or is it just an overkill at this point?)
Im actually building my first pc this week and im stuck on my fan setup and dont know what to do. I have a cpu air cooler with 2 fans on it and 6 140mm fans in my case. 3 intake in front, 1 exhaust in rear and 2 I was gonna use for top of my case and that is where im stuck. My cpu cooler with be exhausting to the rear fan so ill have 3 intake im front to a cpu cooler which is pulling from the front and exhausting to rear so how donI setup my top fans? Also seems I dont have enough exhaust so I wanted to do 2 exhaust in top but with my cpu cooler im confused what to do. Please help me someone.
I donno if I'm correct but here we go..
3 front fan: intake
3 radiotor fan: exhaust
2 bottom fan: intake and 1(I'll place in middle)exhaust.
1 Rare fan: exhaust
Total 10 fans 5 intake 5 exhaust... It that right? Like neutral airflow
I did this mistake with my Ryujin 240 Argb front setup haha, I had it pushing the front instead of pulling air 🤓🤣
yeah with my new build my front 3 are intake and my AIO 360 are exhaust
My only two options to mount an AIO cooler is either on the top, or on the front. What do you recommend? Should I mount it on the front as an intake or should I mount it on the top as an exhaust? What would give me the best results in cooling?
czcams.com/video/qQcyYHGtArs/video.html
nice! what mic do you use?
czcams.com/video/lrIvGvSVKBc/video.html
i bought some reverse flow fans that are unlabeled which makes this extra confusing for me
thanks
No problem. Hope you enjoyed enough to subscribe
what do you think in this scenario.. three 120s front intake one 140 up rear exhaust and top rad 360mm two exhaust (that near the rear 140m and one intake (near the front fans )?
Just got three intake on the front, the rest exhaust.
@@TheProvokedPrawn with my setup you have 4 intake fans and 3 exhaust.. this is positive pressure ..
I dont get it. Whats wrong with the initial RAD fan setup pulling air through? You say its the wrong way?
Thanks
You're welcome!
Why have the front intake fans on the inside of the brackets? They could easily be installed where the radiator could go.
On top of a psu cover, are they intake or exhaust fans? For example the Lian Li can have two fans on top of the psu
That's also my question. Hope someone give the answer... 😰
I heard from another channel it’s exhaust, but not worth it apparently unless you just love rgb fans
Question, when using fans on rad against a case, is there any difference in putting the fans behind the rad or the rad behind the fans?
I've not tested them thoroughly like that so can't say.
In general, no. Maintenance is a lot easier if you pull air through the rad instead of mounting the fans in front. The dust buildup will then only stick to the surface of the rad, and you can easily clean it off. If you put the fans infront, you will see dust buildup on the fan blades and inside the ring.
Airflow wise, there has been lots of testing and in general it will move the same amount of air in the case whether mounted behind or in front.
@@krukis98 thanks!
Having the power supply at the bottom that exhaust to the outside, does it make sense to put the intake fans at the bottom?
That's also my question. Hope someone give the answer... 😰
If your power supply is mounted correctly, it should be intaking air from below, hence why cases have dust filters on the bottom - it isn't to keep dust in!
I really hate how fans have an "ugly" side with the sticker. Obviously they're gonna need to hold the actual fan to the outside of the device somehow but those ugly stickers totally get me. I actually ended up removing all my Corsair fans and replacing them with Lian Li ones just because of those ugly stickers that were sitting right there in plain sight on the bottom intake fans.
Yeah, the back is usually ugly
Interestingly some companies are recognizing this to offer reverse looking fans, like the ones from Montech's Sky Two case, and Thermaltake's SwaFans from CES 2023 where they come with multiple swappable blades
I’ll have to google fan sticker company to cover that stupid sticker
@@Chris-ql3rx I've actually been looking for that and couldn't find anything here in Germany. The only things I found were on eBay and cost liike $35 in shipping per sticker. Replacing the fans entirely was actually cheaper than that XD
Phanteks new D30s have two options, Normal and Reversed. This way you see the front but the blades are reversed, so you get both aesthetics and performance 😊
So side fans should be intake? You didn’t mention side fans at the end
I have 3 intake on front and 3 exhaust on the side (thru AIO radiator) that works guys? Guess cannot add more intake anywhere (no space on the bottom) so I cannot add exhaust at the top if I followed the logic correctly. I am already balanced atm
You can always check to see if there's an issue czcams.com/video/sVEXd-Wp8FY/video.html
Will it hurt if I top mount my radiator and still exhaust through the top
No
Show only the the right way never the wrong.
I've done 3 top intake, 2 front intake, and 1 exhaust at the back Plus the CPU cooler which acts as an exhaust and my GPU temps stay below 60c hotspot can reach max 80c but that's it, CPU stays below 30c but this all depends on your case as well.
Saya sangat senang sekali melihat video video anda
Good vid Prawny but I just wanted to see 30 seconds of how it should be done with that smoke machine! That would have been a very satisfying end to the video.
Good feedback. Thanks!
Another matter is, try always match the fans, dont go frankenstein.
All same manufacturer by minimum.
Bottom intake would mean all the dust from the ground coming in?
If you never vacuum and your case doesn't have dust filters...
In my PC everything is intake except the rear exhaust. is that ok?
You should try and have a neutral pressure and if u can’t make it positive but as close as possible to neutral
How many fans do I need for a full tower pc case?
Depends on the case
@@TheProvokedPrawn Thermaltake Core P8 TG
Basically, the ugly side has to be facing the gpu or the other way around
You showed how not to do it, but not how to do it? 🤔
You only need to know that the front and bottom are for intake, top and rear for exhaust
Just literally do the opposite.... Does everything need to be spoonfed to you?
@@NoReply28 like omg literally 😂
I would rather use static fans for the radiator.
I don’t understand why fans are place behind the AIO radiator and thus cool it with hot air taken from inside the case in place of taking fresh air from outside to blow on the radiator like in a car engine…..🤔
That's an interesting thought. Maybe because cars have to drive forward, so you'd have to mount the radiator behind the engine to have the same effect and it'd then be too obstructed to actually work. 🤷
i have got my 3 exhaust fans on the bottom is that bad ?
It's not ideal imo. It'll be fighting your GPU fans, as I showed
@@TheProvokedPrawn well i guess that is why im getting 80 degrees temp on my Rx 6800 xt i will try swapping them see if temps get any better
Apply some logic on that, how and why would it work
Noctua is the only way to go as all other fans are for minimum wage.
why does every word you say sound like sarcasm? lol . Edit : nvrmnd, the appearance at the end explained everything XD
Maybe because I'm British? 🤷♂️
9 fans has to be loud
After 50 years of building my own PC's, LED's are a waste of space. Noctua fans are probably the example to choose.
50 years? That's amazing...
do your tests with temperatures and not smoke machines next time. also more arrows graphs and on screen written information.
I've tested in plenty of builds but thanks for the feedback
Dude, I think you left your weed out when you were showing us the smoke machine.
Alas no 🤣
@@TheProvokedPrawn wait so what is that in the jars? Deffo looks like some fat nuggies.
@@TheProvokedPrawn lol
@@rachelblake2350 key switches
@@TheProvokedPrawn aaahhh hahaha
Real question is: how to get a voice like yours?
Be born British, have a dad that smoked a lot, be old and use a good mic?
@@TheProvokedPrawn 🥹
@@TheProvokedPrawn whats the MSRP on that? :P thanks for the guide i would add simple drawings to help with the video or suggest some general configurations and point out that some fans are designed more towards moving more air volumen or to get more air pressure
@@Heartofswordx thanks for the feedback
Where’s his power supply?
At the back. It's a dual chamber case
Wtf are you Chyrosran22's brother?
All British people are related I guess.
Im not like him in Orange
why don't show us the right way and call it a day?
I did?
thank god i dont like rgb crab
Case fans in general are a scam really...you will never see a great impact on cooling regardless. The components that utilize fans for cooling is another matter...
Rubbish. I’ve had CPU temp differences of 10C just by changing my case fan config
that is complete bullshit, case fans can make the difference of your GPU being at nice warm temperature, or blue screening due to heat.
i am not putting diarrhea fans in my case
No one said you had to
😅
Noctua sucks