Main Rotor helikopter EXPERIMENTAL HELICOPTER BUILD Aluminum 6061-7075
Vložit
- čas přidán 29. 08. 2024
- Main rotor head 16mm 7075
Right and left side 30mm 7075
Pitch Horn roudbar dia 76mm 6061
.
.
.
.
.
.
.
#Rotorhelikoter
#caramerakithelikopter
#caramembuatdrone
#mesinhelikopter
#mainrotorheadexperimentalhelicopter build series
#EXPERIMENTALHELICOPTERBUILD
#carakerjahelikopter
#balingbalinghelikoter
#pesawathelikopter
#helikoterexperimen
#experiental
Mantap bang Thomas. Tlng video nya dilanjutkan sampai swashplate nya bang. Dan tes momen keseimbangan laju geraknya juga . Inspiratif. 👍🙏.
Good job. Jadi pingin ngelihatnya
Keren sukses selalu 🙏👍👍
Mantul bang,,
I am looking forward to seeing you next video soon.
Your use of Hacksaw Blade & Frame in cutting is tidious. In this modern era, you can use Jigsaw Machine, Angle Grinder to make your work easier
Very good gob
Kren nih.
Subrek ahhh 😃
Wihh keren! Harus jadi ini. Siap supply mesin nanti
Bikin Head mesin 2tak bisa ga mas 😁
Looking good 👍
Hello helicopter youtubers, how about your project ?
Thomas Creator my project is going well thanks, I have tested the rotors to full rpm and full throttle and the helicopter nearly lifted itself but would not lift me as well. My gearing is too high at 5.6:1 I'm going to change the gearing to 7:1 and see what happens then. The empty weight is 118kg so with 60hp I think it should be possible. The tip speed I'm now aiming for is 515ft/sec, I believe this should be somewhere near. What's next on your project? the engineering looks good, looks like you have chosen thick enough materials to take the centrifugal loads. 👍
@@Ben-Dixey it's the same, hopefully my project will also go well, I chose a thick material to make it even stronger he he he,
@Thomas Creator going thicker than you think you will need is good as far as safety but also adds weight. You can work out the centrifugal forces from the blade weight and centre of mass. Then you can use the cross sectional area to calculate the of tensile strength of the parts. What you have done looks good but if you can check the numbers it will give you confidence in your machine.
Sudah jadi om helinya..pingin bikin juga.. 🙏
Please blend those scribed scratches out of the side plates. The alloy you are using is terribly intolerant of fatigue and you have just scratched a a whole load of stress risers into one of the most heavily stressed parts of the airframe. it will kill you if you do not repair it.
Is this a purchased plan or your personal design?
bro, is the material you use steel?
Bikin vidio perakitan helinya bang
😄😄😄👍👍👍
Have you just got one bearing on each fork ?
Bisa lanhsung full set ke mesin gak
Use Subaru legacy engine ej20
Up
Alma nya ukuran berapa dan tebal nya berapa bosku
Loha hai ya aluminium hai
What price?
IDR 10.000.000
alumuniumnya harga berapa'an bos??
Harga tergantung ukuran om
di jual kah bang
Bisa pesen gak mas
Itu aja bayarin
Bg bahan nya jenis apa
Dural 6061
Aluminiu. 6061
@@Thomas_Creative alumunium sudah cukup kuat ya pak? Bukannya besi baja yang lebih baik? Atau keberatan
@@dianarianto3776 besi baja terlalu berat om
Cómo puedes usar un un instrumento de medida para un trabajo de precisión que no funciona,para eso usa uno que no sea electrónico.