Awesome video. Appreciate you getting to the point and not blabbing on about other random unrelated stuff. First time doing an impeller an Got it all taken care of in a little over an hour. Could have went way faster but wanted to make sure it was done right with no extra parts left over. 🤣 Thank you!
Good video, very helpful. I have never seen a torque spec that was without lube. You're not doing it wrong by adding lube, you're doing it right. And not to be picky, you are working with the key. The keyway is the groove in the shaft and impeller.
I hope you meant the spacer and yes sometimes they will slide off with the lower unit just make sure when you reinstall it you add some grease to the studs so you do t get corrosion build up there
Great video. My lower unit will not come off same motor. Will not budge at all even if I lower it down and stand on it and I have all 5 bolts removed. Any tips?
Leave one bolt loose and on the side you will have to pry between the lower and mid housing usually it’s stuck at the front Dow pin and side studs . You may need some on blaster or heat depends on the amount of corrosion
I same engine SN 2B608397 I am looking for the bearing nut assembly removal tool. What it the right size. I have to change out the prop seals and I need a couple tools I do not have. Do you have links to the tools or part number for the tools.
Use an inch pounds torque wrench 1/4 inch drive for the water pump bolts and thx I may just do a vid on the stand we made it the night before with left over scrap 2x4
@@ShallowHookerFishing thanks. Do you have a make and model number for the wrench? I'm expecting delivery of a Ranger 2510 with a 300 hp mercury and would like to do the 100 and 300 hr. Maintenence myself.
It doesn’t matter you can go to lowes and get a craftsman or husky from homedepot the one I use is a snap on and it cost around 400 bucks so that may not be for you but a cheaper one is fine 50- 100 bucks
Great video. My lower unit will not come off same motor. Will not budge at all even if I lower it down and stand on it and I have all 5 bolts removed. Any tips?
Awesome video. Appreciate you getting to the point and not blabbing on about other random unrelated stuff.
First time doing an impeller an Got it all taken care of in a little over an hour. Could have went way faster but wanted to make sure it was done right with no extra parts left over. 🤣
Thank you!
Well done! Every CZcams DIY should be this good! Thanks!
Thank you! 😊
Thank u from France
Good video, very helpful. I have never seen a torque spec that was without lube. You're not doing it wrong by adding lube, you're doing it right. And not to be picky, you are working with the key. The keyway is the groove in the shaft and impeller.
60 inch lbs ,water pump cover screw (4)
Great video!
great video
Great video. I have a question though. After the first 6 bolts/nuts removed. My upper and lower unit dropped together? Why?
I hope you meant the spacer and yes sometimes they will slide off with the lower unit just make sure when you reinstall it you add some grease to the studs so you do t get corrosion build up there
Great video. My lower unit will not come off same motor. Will not budge at all even if I lower it down and stand on it and I have all 5 bolts removed. Any tips?
Leave one bolt loose and on the side you will have to pry between the lower and mid housing usually it’s stuck at the front Dow pin and side studs . You may need some on blaster or heat depends on the amount of corrosion
Thanks .. I am looking to repower . Replacing 150 etec evinrudes with 150 4S mercs.. what kind of performance are you getting?
Just to confirm torque settings: Torque water pump bolt to 35 Ib. in? Thanks!
Will I need to re add lower unit oil after it’s replaced ?
I same engine SN 2B608397 I am looking for the bearing nut assembly removal tool. What it the right size. I have to change out the prop seals and I need a couple tools I do not have. Do you have links to the tools or part number for the tools.
Should it be shifted in rev/foward or ledt in neutral?
Neutral
Nice video! What size torque wrench do you recommend? Will you do a quick video or send me the specs on your lower unit holder? Looks good.
Use an inch pounds torque wrench 1/4 inch drive for the water pump bolts and thx I may just do a vid on the stand we made it the night before with left over scrap 2x4
@@ShallowHookerFishing thanks. Do you have a make and model number for the wrench? I'm expecting delivery of a Ranger 2510 with a 300 hp mercury and would like to do the 100 and 300 hr. Maintenence myself.
It doesn’t matter you can go to lowes and get a craftsman or husky from homedepot the one I use is a snap on and it cost around 400 bucks so that may not be for you but a cheaper one is fine 50- 100 bucks
@@ShallowHookerFishing excellent! Thanks
Great video. My lower unit will not come off same motor. Will not budge at all even if I lower it down and stand on it and I have all 5 bolts removed. Any tips?
Your missing a bolt underneath. There are 6.
@@catherinedubois1071 where is the 6th? 2 on each side and one under anode