CUSTOMER STATES FAILED EMISSIONS TEST! HOW TO ADJUST A HYUNDAI TURBO WASTE GATE FOR CODE P2563!

Today I show you how to adjust a Hyundai turbo engine wastegate actuator enjoy!
Tools used in this video.
Milwaukee underhood light- amzn.to/3PVTLh7
Milwaukee meter- amzn.to/3sVo3qW
Electric lead/wire kit- amzn.to/3ZrNuN3
Sunex 3/8 set- amzn.to/3ui3538
Gearwrench ratchet set-
Pb blaster- amzn.to/3ENp5rQ
Vise grip- amzn.to/3rkno1S
Mechanics mirror- amzn.to/3ELBjkF
Pick set- amzn.to/3PrL2l7
Pry bar set- amzn.to/3KRSaph
As a amazon associate I do earn a commission on qualifying sales if you use the link.
I'm not sponsored everything shown here is purchased with my own money and are used by me in everyday work.
Disclaimer:
Due to factors beyond the control of The Enthusiast Mechanic, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. The Enthusiast Mechanic assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. The Enthusiast Mechanic recommends safe practices when working with tools or equipment seen or implied in this video. Due to factors beyond the control of The Enthusiast Mechanic, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained.

[@charliewernette]

This is an easy fix you can do with minimal tools and parts , and if you are getting the boost pressure sensor error it's either out of adjustment or you need to replace the entire actuator motor(that was my fix, and adjusting the rod to 4.0V) might need some probes/hooks to get the c-clip off and back on as that is the most difficult part of the entire procedure. You will need a voltage reader also, you don't need a diagnostic computer to do this fix. Once you remove that section of hose that blocks the actuator it's easy. Some other videos don't correctly tell you how to adjust the rod, the wastegate needs to be in the most upright position like he says in this video to get closest to a 4.0V reading. I ordered the actuator replacement online and had it next day cost $80, spend some money on hook tools to get that c-clip off also bought a new hose clamp because the stock ones are a PITA to work with when re-attaching the portion of the exhaust you remove to get to the actuator motor. The dealership service department I went to initially charged me $175 just to diagnose that it was the actuator that failed took them 30 seconds, then they wanted to charge me $800 parts and labor to fix it, fuck them do it yourself if you have this issue, don't get ripped off! Dealerships have no shame and are only worth going to if you need a diagnostic report, anything that isn't warranty work they will rip you off so bad it's sickening!

[@Pierorocks]

big help with the PB blaster, i will definitely need to use that on my parts, and to help get that e- clip off. unfortunately, the top bolt on my hat shield snapped in half as i tried to loosen it, so now i'll have to try and deal with that. any tips on how to remove the other half of a snapped bolt still in the top heat shield hole? oops!

[@TheEnthusiastMechanic]

Your best option would be to try to use a broken fastener extractor, but if it’s really rusted in there, I would probably just drill a little hole on your already broken fastener. Just make sure you get it centered and use a sheet metal screw, that’s not too long just to hold the shield on you don’t wanna go through the manifold.

[@macielandsons]

What color wire did you probe on the waste gate wire ?

[@TheEnthusiastMechanic]

I said it in the video the yellow wire but it can vary depending on the model