Bosch GBH 2-24 D Rotary Hammer Repair
Vložit
- čas přidán 26. 07. 2024
- In this video I restore the Bosch GBH 2-24 rotary hammer. It had a broken mode switch. After disassembly I found the plastic on the stator melted due to overheating. But surprisingly the stator still worked. I also replaced one bearing on the rotor. All other parts were in good condition.
00:00 Inspection
00:21 Dismantling the perforator
05:28 Impact bolt repair
06:04 Rotor bearing replacement
06:26 Checking the stator
06:41 Stator repair
07:36 Hammer drill assembly
17:09 Checking work - Věda a technologie
beautifully reassembled , nice camera work , nice editing ; you made it look effortless ! well done
Thank you!
Buenas Tardes Señores excelente sus videos; disculpen les agradezco le agreguen a estos videos Audio ya que para nosotros los que estamos aprendiendo e iniciándonos en el tema de las reparaciones de taladros y pulidoras es fundamental la enseñanza a través de Audio; muchas gracias; Bendiciones
Muchas gracias
It was helpful, thanks for the video.
Buen video gracias
Te felicito
Gracias
Bosch GBH2-24DRE Switch Holding Plate
pembongkaran [2:58] - [3:45]
pemasangan [8:59] - [9:16]
Thanks sangat membantu
Hola, muy buen video. Te hago una consulta, tengo la misma maquina pero ya no golpea, en modo percutor no gira mucho y no golpea. Que podría ser? Muchas gracias
Hola. Es posible que sea necesario reemplazar las juntas tóricas de goma del mecanismo de choque.
Sorry I want to ask. What should I replace? Is there a problem with the armature? I have the same model 2-24, the problem now is that it can turn, but it turns slowly like it loses power and when turning the spark is green. carbon brush is still long because this drill is new and rarely used. Thanks you
There may be a short circuit in the stator or motor armature. Another issue could be the bearings. It needs to be taken apart and diagnosed.
Y donde se puede comprar gracias
Buen día tipo de grasa lleva
Perdón la armadura me da 1.2 homs y vi n el video que da 2.7 me sirve todavía o tendría que cambiarla
Switch replacement
Hola el mio prende pero no tirne fuerda ..el rodamiento de atras se bario me parese cree q sea solo eso o debo de canbiar toda la armadura .
Hola. Podría ser el rodamiento o la armadura. Necesitamos comprobarlo.
my selector now won't turn. Its a 25 year old GBH 2-24 DFR, woud you be interested in fixing it? if not, where do I take it....great vid btw. Adam
Thanks, Adam. I'm too far away from you to help repair it.
can replace armature with dre 26 to dre 24
no
Hola, no tiene mucho juego el eje? La mecha no gira recta
Hola, tal vez el juego es demasiado grande, pero el taladro no se cae.
hola,que tipo de grasa utiliza?
Hola, Grasa especial para cajas de cambios de herramientas eléctricas.
poca grasa😱
Здравствуйте. Немного нагрузку на него увеличил,теперь сверла с люфтом небольшим гуляют и бывает чуть поработает, после может сутки не работать, а через 24 как часики И ТАК ПО КРУГУ. В чем проблема, помогите Люди добрые.Заранее благодаря. Написал сюда, так как он аналог БОША.
Здравствуйте. Разбирать и смотреть. Если люфт появился, то износ. Если не включается, то контакта где-то нет.
Perdón qué tipo de grasa lleva como se llam
Dar la bienvenida. La grasa se llama Ultra 0.
Entra energia a la maquina pero no funciona
❓
O my good, very bad