How To Make A Kydex Sheath Taco Style | Knife Making
Vložit
- čas přidán 28. 05. 2020
- Up until recently I've been making pancake style kydex sheaths; however, in an effort to try something new I've ventured into making taco style kydex sheaths. I must say that I enjoy making the taco style sheath more. It's easier during the construction phase of the sheath since it stays together easily. I also like being able to add a sweet thumb ramp to the back of the sheath (not the thumbnail for this video doesn't show the thumb ramp I eventually put onto that sheath!). I hope yall enjoy this video, if you have any questions feel free to drop them in the comment section below.
✅ Supplies & Materials:
Best Kydex Eyelets - amzn.to/2LeLlkI
Kydex (goes in and out of stock) - amzn.to/2JED0U0
🛠Tools and Gear Needed:
Kydex Eyelet Dies - amzn.to/2JujjzE
Gloves (rubberized) - amzn.to/34xSVft
Temp Gun - amzn.to/2G3Xrsr
Heat Gun - amzn.to/3d8vyOt
Hinges to Build Press - amzn.to/2xF1VkR
Foam Source - www.knifekits.com/vcom/moldin...
✅ Clips & Mounting Options:
UltiClip Slim 3.3 - amzn.to/2NxCaKS
TekLock - amzn.to/2jZeILM
Paracord 500ft - amzn.to/2Js7ObS
🗡Knife Builds:
Hunting Knife With Bolsters - • Bolsters on a Full Tan...
Boat Knife - • How To Make A Knife - ...
Rod Pump Knife - • Making A Knife From Oi...
📷Camera Gear:
Camera - Panasonic G7 - amzn.to/2SD8ekG
Microphone - Takstar - amzn.to/36euYLP
SD Card - 128GB - amzn.to/2tmVfZW
Narration Microphone - amzn.to/2XvKHD2
**************************************************
Subscribe Here: / @redbeardops
**************************************************
Instagram: / redbeardops
Twitter: / redbeardops
#knifemaking
#redbeardops
#kydex
**********************************************************
The information provided on this channel is for entertainment purposes only. Any action you as the viewer takes upon the information on this channel is strictly at your own risk, and I will not be liable for any losses, damages, or personal injuries in connection with the use of this content (including injuries, damages, or losses sustained while you were trying to emulate the actions and projects on this channel). Attempting to emulate any of the actions or projects put forth by this channel should not be done without training and even then, at your own risk. - Jak na to + styl
Soo... what's better? Tacos or Pancakes!? 😜
I'm thinking taco. At least for knives, guns might be better with pancake. Have to look at some more examples before locking my final answer.
Taco for sure. However I really depends on the type of blade, the and how you want to use it will depend on the type of sheath style
Taco is a excellent idea and one more option to know. In my case i discovered it today. Thanks from Brazil!
Pancakes for breakfast, tacos for lunch...LOL
Oh... that sounds REALLLL good
Beautiful … and crystal clear instruction. Bravo.
Glad it was helpful!
@@RedBeardOps Top notch!
I like how you oiled the blade before adding the tape! You didn't bring attention to it but that is another great tip! Taco for me! Great video man
Thanks a million man! Good point. I don't like leaving that tape on the blade for extended periods.... It can trap moisture if your not careful and rust! Thanks for your comment as always, sir!
That click when the knife goes in the sheath.....Sooooo nice sounding. :)
Satisfying for sure!
That little click gives you confidence that your blade is secured.
I like it!
🇬🇧🤜⚡️🤛🇺🇸
Darn right, Cheers sir!
It's all in the details, well done!
Thank you as always sir! Really appreciate your comments.
A pleasure watching as always, I’ve only been making knives in the UK for around 4 years, so your experience and knowledge that you show in your videos is very much appreciated. Thanks and look forward to watching more 👌🏻👍🏻
Great to hear! CHeers
You’re making some of the better knife making videos I’ve seen lately.
Hey Josh, I really appreciate that! I'm trying my best. Have a great weekend!
Dude, your videos are great. So many people teach people HOW to do things, but they don't explain the WHY behind what they're doing. I've watched dozens of videos on making sheaths and you're the first person to mention the benefits of utilizing 3/4" hole spacing.
Thanks Nick, I'm doing my best get get all the details out there that I learn. There is so much to learn!
Great video, love the thumb ramp addition...
The arbor press for eyelets must be a massive hand/finger saver. Love the video as usual.
1000% yes!
You are a beast man. So clear and precise
Hey JC, really appreciate the praise! Thanks for the comment and thanks for your viewership!
You did a really great job with this! I love how everything is right to the point. Thanks dude!
Glad it was helpful!
Awesome video dude. So much to learn from you 🙏🏽🙏🏽
Thanks man! Really appreciate your comment. Glad you liked the video.
Good job! Great video as always. You were the one that I got the idea from to start using ulti clips.
Heck yeah man! Glad you liked it. I love those clips... very strong.
Whoa whoa whoa there partner this video quality is way too good for a CZcams. :) lol
Lol! Thanks sir! Really appreciate your comment!
I really enjoy your videos man. Thanks for the content.
Thanks skip! Glad you're like them!
Great video! Thank you so much for his detailed instruction material 🙃👍
Glad it was helpful!
Excellent video on Kydex. I have made a couple pancake style, but never taco style. I really like the thumb ramp idea, and using an arbor press looks so much easier than a hammer. I think I have to make a kydex sheath now!
Cheers from Canada
Heck yeah man! Glad you enjoyed this one. Cheers from Texas!
I just ordered the hinges to build one of these presses to build eleven sheaths for my three year project , hopefully I will stay healthy enough to get them done this year around Christmas as gifts, getting older has its setbacks, stay young as long as you can , I enjoy your channel and your videos. Thanks
Thank you greatly sir! Good luck with your sheaths!
This video was extremely helpful for making my first kydex holster
Glad I could help!
Your a good craftsman that worked out good.Have good weekend .
Thanks Jim, you too! Cheers sir!
Dude! Excellent video.
Glad you liked it!
Thanks for the vid about to make my first taco!
Well executed instructional. Thank you.
Glad it was helpful!
@@RedBeardOps Most helpful. Im making my first one this week.
Taco makes a cleaner look, I like the thumb release idea.
Met too! Cheers John!
Excellent tips. Thanks!
Glad it was helpful!
Outstanding 💯
Thank you! Cheers!
Good job my man!
Appreciate it!
Dude this was great info thank ypu!
Cheers sir! Thanks
Great Video.
Well made video. Thank you
Glad it was helpful!
Nice work dude
Much appreciated!
Great info. You made it look easy 😆
Glad it was helpful!
You are really good at making knives man
Thank you! Really appreciate that.
thanks for the vid bro looking forward to trying my first kydex sheath, thanks!
Good luck!
Great vid! thank you!!!
Glad you liked it!
I love your videos keep up the good work
Thank you! Will do, sir!
Hey man I made a few knives since I last said something on ur vids but they are turning out better each time. I will be trying this as soon as I can get my hands on some! Appreciate the tutorials
Awesome sir! Good luck with your builds!
Good video man
Thanks for the visit!
Very helpful!
Glad it was helpful!
Nice sheath! I also like to hit the sanded edges of the sheath on the buffer. Gives it a very clean look.
Thanks Chris! I'm going to need to try this. I don't have a buffer, but maybe some little buffing wheels on my dremmel will do the trick.
Nice one
Great video. I also do the thumb areas but I don't have a heat gun.. now I think I need one. ;-)
Heck yeah sir! Glad you got something out of it. Thanks for your comment and have a great weekend!
Great video! Subbed!!
Awesome, thank you!
Love your videos, wondering about the arbor press what tonnage is it (1/2,1,2)? Link to the dies used? Thanks again for the great content
Muy intructivo.Saludos desde Panama
¡Gracias por tu comentario! ¡Saludos desde Texas!
Good video 👍
Glad you enjoyed!
Loved the vid man keep it up!
Ps. You should consider some music backgrounds from epidemic sounds 😉
Thanks man! Thanks for the recommendation, too! I've checked them out for sure and they're at the top of my list. I'm just too cheap right now... LOL
Thank you for this vid. I have so many issues with Kydex. I went to leather because of it. This helps a lot. I have some things to try.
Thanks for your comment man! Leather is hard! But I plan on getting better at it too hopefully in the coming months. Have a great weekend.
I know this comment is a year old, but what issues do you have with kydex?
@@LanceJoshlin a lot of the issues I had I have figured out. Mainly the spacing of the eyelets from the knife was a main issue. After figuring out spacing, it got much easier
Best knifemaker. Ай виш ю 100000 субскрайберс квикли!
Thank you!
Great video thanks. Nice beard friendly respirator! 👍
Cheers Kelley! I have a new respirator review coming out soon... it's an expensive one though
No drainage hole?
Thanks for the tutorial, I was just wondering how exactly to make kydex items and your vid was the 1st one I picked. Good job. I especially like the foam press
Glad it helped! You can put a brass rod in the crease to add a drainage hole; or drill one. Cheers!
Taco is better for one-sided blades, pancakes are better for double-sided blades because you don't want one side rubbing on the spine of the taco sheath.
Good points!
You’ve done it again, another awesome video man! I was just curious about that clip. Does it allow for scout carry of the knife?
Thanks Kevin! Yeah the tek-lok does allow for scout carry. The Ulti Clip is more of a concealment clip.
Red Beard Ops awesome man I’ll have to check it out. Not sure about you, but I definitely prefer scout carry when available, especially for a smaller fixed blade. Just more convenient for me personally
Awesome. Definitely subbing after seeing this video.
Do you do this for a living?
Thanks Chris! I do not. Cheers!
Well done! How dense is the foam sections you use in the press and what do you suppose the longevity of this foam is before you would need to replace it?
I've used the same foam since 2019. I got it at knife-kits . com I think
Great video from start to finish! I also noticed the blade oiling before taping and like that touch. Especially liked the “thumb-ramp” tutorial as well. I’m about to make my first sheath and this video has my confidence high!
Is that .06 or .08 thickness and do you change your heating method depending on which you use? I noticed you go high heat to 285°. I’ve seen others do slow and low to 350°. Any pros and cons?
Thanks man. Sorry if this has been answered elsewhere. 🤘🏻
Thanks! I put a link to the kydex I'm using in the description of this video. Not sure about the pros and cons of the heating cycles. I think this stuff gets dangerous to breath at a certain temp
Wow good video man what measure are the eyelets
Hey Manolo, I have them linked in the description.
What are you using to clamp down your 1 2 3 blocks? I'm new to making sheaths and I'm getting my supplies ready.
Those are just some cheap hold downs clamps I use on my mini mill
Well that doesn't look too overwhelming. Since I'm in a rare area where I don't have a kydex guy near me or within my network, I guess I'm going to be that guy.
Good luck Aaron!
The straps you have pictured on screen at 6:49 where can I find those exact ones? I’ve searched for “knife sheath straps,” and can’t find those. This is another reason I like your videos because they’re concise and that picture is exactly what I’m looking for for sheath straps
I have a link in the description with all the items. Cheers man - TekLock - amzn.to/2jZeILM
What thickness of Kydex are you using? And what size are the rivets please. I want to order some supplies to try this but, I'd like to order the right stuff...LOL. I know, where's the fun in that...
Cheers from Canada
Sorry Sir I should have put that information in the video. Check out the description for links on the exact kydex and eyelets I use.
Is it possible to use a tension screw to determine and set the sheath retention (like is often done w/ kydex gun holsters) instead of the method you used?
Hey Jeffrey, I haven't tried it, but I'm sure you could! I'd put it at the top hole.
Beautiful knife and sheets. Where do you get your respirator?
I found it on amazon, but I'm not sure it's carried anymore... "Resp-O-Rator"
It’s not carried anymore,, thanks for the return!
When you're grinding, what kind of respirator are you using? I've never seen anything like that before.
amzn.to/2M6PMN7
What is the safety device on nose and mouth? Nice video
Hey man I got it here before it went out of stock for COVID. I love it... great for the bearded - Checkering File - amzn.to/3bg2iER
Nice video! I want to make kydex sheaths for a lot of knives and multi tools I have. I don’t know if I missed it or not, but which thickness of the kydex do you think works best? Thanks
The stuff I use is 0.060" . I think I have a link to it in the description. Cheers!
@@RedBeardOps thanks for the help. I got the kydex and built the same setup you did. Trying to figure how hot and long to heat it up. Trying to do a taco style. I’ve learned a lot off your channel. Thanks 🙏
@@eheritage21 I use a cheap temp gun and get mine up to around 280F
I really like this video. You definitely take your time, and look for the best possible finish. I just purchased at Fox European hunter, very small knife for small game. I was wondering if I could commission you to make a sheath for me?
Hey Scott, I'm not taking any customs. Thanks though!
What's that respirator/PPE you're wearing during grinding?
Resp-O-Rator - amzn.to/2M6PMN7 - Cheers!
Really Like your Videos. Btw Stick some foam into the opening to keep grinding Media Out ... Works for me best regards
Thanks for the tip Fred! Have a great weekend!
@@RedBeardOps thanks.you too
What thickness kydex are you using in this vid? Is it the 0.060? What would be the downside in using 0.028?
That sounds about right... I think you'd get weaker retention
I prefer the pancake because of slimness, is there benefits to Taco vs pancake?
Hey Tim, I don't see an advantage other than maybe the thumb ramp is easier to make on the taco. The pancake does have the advantage of mounting holes on both sides for being strapped down easier.
Why did you put balistol in the blade before the tape? Thanks!
Hey John, I put that stuff on all the time. May be a little parinoid. If tape is left on there for a long time it can attract moisture
The press doesn't compress at the hinged end. Does that matter? I have some materials on order and planning on making the press before they get here, but don't know what to do at the hinged end, maybe pre-compress it at that end. what do you think?
While I think a better solution would be even pressure... I haven't had issues using the hinged design.
Don't wanna sound like a complete dope but I'm getting a small arbor press and those dies but how does the top die stay? Is there a hole or how does that work? Thanks!
Hey Jimmie, I drilled and tapped the arbor with a set screw for holding the top die.
@@RedBeardOps ahhh gotcha, I can do that! Thanks for the info and for responding 👍🏼 excellent video by the way!
How long do you keep the kydex in the press?
about 10 min
What kind of foam do you recommend ?
stuff like this - www.knifekits.com/vcom/holster-making-tools-molding-presses-foam-c-1072_524.html
Very nice!... Do u take orders?.. I have a KOA BUSH CAMP.
Sorry sir, I am not taking any orders. Cheers
I’ve been doing pancake but like the taco option. BUT I’m not having much success. They are coming out really loose and looking all wavy. Any suggestions?
I think I figured out what my problem was. I don’t think I was getting the kydex hot enough. On my fifth attempt I heated it up to 315 degrees. Had the consistency of a lasagna noodle. Layed the knife on it an folded. Than clamped the crap on the press. (Copied your press.). After 25 minutes took it out and looks great.
Heck yeah Gerald! Glad you found a solution.
What thickness of kydex do you use? Thank you
I put a link to the kydex I use in the description of this video .Cheers!
@@RedBeardOps Thank you. You are the best!
Hi, what kind of spon material to press?
These guys used to sell foam - www.knifekits.com/vcom/advanced_search_result.php?keywords=foam&osCsid=aebd34888f0679e7df4677ce659ee439
Thanks. Sometimes it is nice to see someone else's techniques
Thanks Corwin!
@@RedBeardOps I recently got back into making knives after few years away. And watching your videos has been a huge inspiration. You make things look so easy. Haha. I hope to someday be able to produce something like you. Check out Raven Blades on Facebook. That's me. Based out of Ontario Canada
@@corwinniederer9763 Will do man. Really happy you found these motivating! Have a great weekend!
What did you turn the oven on for
1:50
At 4min 30 sec, you point to the retention spot of the sheath. Have you found that this will leave scratch marks on the finished blade over time? Is this normal or do I need to do something to prevent this?
Dirt, grit, grime will get into kydex sheaths and scratch your blade for sure. It's tough to stop this.
@@RedBeardOps I tied a clean rag to a long string and pulled it through like a bore snake a few times before setting the eyelets, but it's still rubbing the etched finish a little. Maybe this is just normal, but it still bugs me
@@hayworth.handmade This is one reason I learned leather work
Do you do custom sheaths i have a custom knife
Sorry sir, I do not. Cheers
What is the style of the knife in the video?
Small EDC Droppoint?
Is that 3/4 of an inch from center?
yes
@@RedBeardOps thank you so much
You need to add water drain hole near the tip
Always a worthy addition via a pin added during pressing or drilling a hole! Thanks for point it out.
can i send you 2 knives to make sheaths for hahahahaha man thats nice
Lol, thank you sir! Glad you enjoyed the video!
Pancakes are easier, Tacos more esthetic. Anyways, just do what you like. It will come out beautiful. Thanks, RBO.
Cheers Kerry!
Which is better .06" kydex or .08" kydex?
depends on your application and desired retention
@RedBeardOps so the thicker it is the better the retention?
@@Drifting_Ghost that is correct. the whole sheath will be more rigid as well
that being said.. I use the 06 and it works great for knives...
Could you just tap the eyelets in with a rubber mallet?
No sir, I doubt that would do it
Pancakes
I do have a soft spot for them! LOL
Rather than rivets what about CA or epoxy glue
I wouldn't trust the sheath to be robust without rivets.
What was that belt clip at the end of the video? Does it pinch onto the belt to not allow slipping?
Check the video description for a link to the cilp
if its not open like a taco its not like a taco
lol