SubiSpeed - 2015 WRX & STI Whiteline Sway Bar Install DIY
Vložit
- čas přidán 5. 09. 2024
- Find out More: www.subispeed....
------
Get some much needed rotation at the track with a Whiteline HD rear sway bar. Check out the install and how easy it is!
------
Snapchat - Subispeeddotcom
Twitter - / subispeeddotcom
Instagram - / subispeed
Facebook - / subispeed
Here are the torque specs from the service manual:
Bushing clamp (2) - 22.1 ft-lb
Endlink (2) - 28 ft-lb
Lateral link 17mm - 59 ft-lb
If you don't torque correctly, it will CREAK !!
Which one is the Lateral link? Just installed this yesterday and I have a lot of creaking on every little bump.
What would the torque specs be for the added brace?
@@Cnbecker9 the same as listed above torque is more dependent on the bolt diameter than the stack thickness
From the Whiteline install PDF
Caution: Always start with softer setting rather than harder.
- Always use new hardware if supplied.
- Tighten all fittings with the vehicle at ride height
Pull the end links off with the sway bar if you're going to be replacing them. They can be a pain to remove if you have some milage on the car. Also, this should be done with the rear suspension loaded at your planned ride height. Back on to some ramps... It works really well, just make sure the ground is even.
I was going to say, suspension should be under load when installing.
Sorry if this was covered, I didn't see it in my scanning. But aren't you supposed to put the weight of the car on the suspension to settle the bushings before you tighten and torque them?
Can u please explain why is it necessary to put the weight on suspension to settle the bushings??
@@sumitpatil6346 Given these are suspension bolts, they have to be tightened and torqued to spec underload otherwise they might creak or even come loose.
Are the bushings really greaseless? I've read that they now require grease because of noise after being installed for a while.
Use grease to be safe
Should absolutely use grease on the inside and outside of the bushings. I use white lithium grease
This is 1,000,000 times easier if you drop the exhaust like SubiSpeed did.
Was going to ask if this was mandatory or just a recommended thing... I will probably pull mine, or at least disconnect at the same point, as I already need to replaced that gasket anyways..
The Y pipe (exhaust) can get in the way of the rear Whiteline Sway Bar. You may need to remove it, easier if you have an Invidia installed. The stock might be a PITA.
also, what is the torque spec for all the hardware?
I have this set up on my 08 sedan wrx and boy it really keeps you glued to the ground.
Been following your building since day one, you are definitly making me want a '15 wrx even more. Great videos!
Why does no one talk about the booklet instructions from whiteline showing that spacers must be added together in order to shift the centerline at the LCA side of the end links? In theory not doing so would apply a partial lateral load on the LCA instead of just perpendicular. Am I the only one overthinking it? It would be really hard to shift the end link center bolt sleeve, pretty much requiring a bushing press every time you want to shift between Low,Med,High levels. Has anyone had issues because of this in the long run? 🤔
Bro, you wear your watch while working on the car? I'm surprised the watch band isn't covered in black grease yet! 😅
can one install new bar on ramps or is it recommended to with suspension unloaded say using jacks?
I'd say put it upon jack stands while you're doing the swapping, the set it down onto ramps when you go to tighten everything up.. That is what it seems like would be the best way to do it as I've been researching this install lately for both the rear and the front say bars... Plan on doing either lowering springs or coilovers at the same time...
In this video is that a 22mm sway bar? I know Whiteline now has several versions you can get.
Should have held both ends stationary and adjusted endink with the gold adjuster. Equal threads.
Finally got mine installed on MY16 today this video was great thanks alot
This video was amazing in detail, thank you!
What size sway bar did you use?
What are the torque specs for this install?
Read comment above. Was answered.
What size sway bar is that? 22mm or 24?
This video was my savior! Thanks!
they include a bunch of Extra washers…what are those for!? I didn’t see this video use any so neither did i
Can anyone tell me what size those bolts are? Lol I can’t find it online and need to replace one of mine. Thanks
Thanks for the video. Was really helpful every step of the way
Do u need an alignment after installing?
Is the softest adjustment for the Whiteline more stiff than the OEM?
Yes by 35%
Do you guys have a video on how to put on the front strut tower brace?
Is this the best option for the WRX to experience more oversteer than understeer? Thanks!
Somehow my endlinks didnt come witha 14mm bolt, so when I try to put the 17mm on it just constantly spins...wtf
The new ones don’t have the hex nuts anymore. I instead they have a hex drive for torquing. Had me confused for a while when I went to install
Can you install the rear sway bar with the car sitting on the ground?
what are the torque specs for all the bolts? also shouldnt they be torque with the car with load?
Hello do you have to remove part of your exhaust? Thank You
That compatible with my Subaru forester XT 2015?
Where is is the link to the end link on your website?
Nice looking bar
did you take them apart and put grease in the links?
would this be fairly similar to the 2008 sti? i'm assuming so.
Has anyone tried the soft setting on these bars? If so what was the reult?
How does the medium setting compare to stock ??
What are the torque settings for each bolt?
+Dustin Christy 33lbs of torque
Dustin Christy in the instructions manual
I noticed you install what appears to be new bushing brackets. I'm curious what brand they are or if they come with the bar kit. The current kits from whiteline (bsk018 specifically) doesn't appear to come with those new bushing brackets.
how much torque is required on those bolts? same goes for the strut one. Just curious if it's a certain amount, of just by feeling
I still wish you were the guy that does the install videos. Easier to go point by point on ur explanations
will this fit a 2015 forester
xt
did you guys buy the base model wrx?
Great video, very professional!
If I install these front and rear sway bars/end links. Along with coilovers, dropping 1.5”. Do I have to change the length of the end links? Or keep them the same length as the oem
when you're installing the rear sway bar/end link does the car need to be on a loaded suspension? or can it just be up on jackstands?
is it ok to fit coilovers first and then fit everything else after wards? or get everything together then align?
Another awesome video!
What do those red pieces of plastic on the endlinks do? Are they just a protective cover for the rubber? I noticed you installed without them.
Atomic Rooster Just a cover.
***** after doing the install myself I believe that would be impossible. You'd be unable to put a wrench around the nut next to the rubber boot. Grease your wrench a little to do that BTW.
does all this come with the sway bar on your website or are they sold separately?
The support bars come with it. The end links are separate and in the related products on the bottom of the page.
www.subispeed.com/whiteline-rear-sway-bar-20mm-22mm-24mm
The little side locks you guys added at the end was that included in the sway bar kit or is that sold separately?
Included in this specific kit that we installed :)
@@SubiSpeed does the lock do anything? other sway bars dont come with them...
Is there a difference between the WRK and the STI sway bar? I understand there was quite an improvement in the suspension of the '15 suspension and I'm wondering if this will really be necessary for my STI Launch Edition.
The STI has a 20mm rear sway bar whereas the WRX has a lesser 18-19mm rear sway bar. The Whiteline adjustable rear sway bay will benefit either cars and will also fit both cars.
OCTurboJoe Agreed! Thanks for the reply :)
SubiSpeed Thanks for the video. This is definitely one of my future mods.
OCTurboJoe from what I've read the wrx has a 20mm rear sway.
If it is true, I stand corrected.
Could someone assist with the torque specs. Thanks!
Read comments. Answered
Is the Whiteline end link really necessary if I don't do track? And if I'm only using 20mm? (just trying to save some $ if it's not necessary)
Not necessary, but highly recommended still.
thank you!. (just trying to save some $ if not required.) this kit does start to get expensive!!
I seemed to miss but, what is the mm of that Whiteline rear sway?
We did not mention in the video what we used, but it is the 24mm. The largest bar that is offered at the moment.
curious, at the time, was the front sway bar stock? whats the best set up for slight oversteer as far as sway bar sizes and adjustment
where can i get the gold support bushings for the endlinks? i cant seem to find them on your website
Whiteline changed the bushing colors to black a year or so back. :(
i see, im not so much worried about the color, i just want the bushings. the kit i bought didnt come with them and i was wondering if they are sold separately. thanks for all your info btw
what size are the bracket bolts and endlink bolts? I really need to find the correct bolts in order to install the bar
Nice crown and buckle watch band! hahah
What is the purpose of brace??
Reduces flex and stiffens the chassis.
If possible can you please make a video on it how actually it works
Hey what kind of wheels are those?
www.subispeed.com/wedssport-sa-10r-zbb-18x9-5-38-r-face-2015-wrx-2015-sti#.WPTTZNIrJhE
Thanks!
Change those tyres while you are at it dude.......
Man those Rs3's are bald
Is it
Tires looking kinda bald there
Them tires are almost gone lol
C as was
Put some goddam grease on your threads ! ;-)
I just took the entire bar off with the endlinks still on the bar LOL
No torque specs, no grease on bushings, no measurement matched endlinks, not even correct procedure to avoid pre load.
Horrible tutorial.
Another video with no torque specs...
bfy.tw/KvKJ
Or you could just put a small load on the suspension by using a jack so the end links aren't maxed out... but, I know, fuck me, right? lol Seems too simple...
What wheels are those??
Wedssport SA-10R GBC - www.subispeed.com/2015-subaru-wrx/wheels-and-accessories/wheels/enkei-nt03-m-silver-18x9-5-38-set-of-4-2015-wrx-sti-4320.html
oh wow. great price too SS!
does the softer setting give you more or less oversteer?
Juan Carlos de Diego less