Making Hydraulic Power Unit
Vložit
- čas přidán 16. 02. 2024
- You often ask about the welding table - amzn.to/3SKx6Eq
The hydraulic system in the workshop will be very helpful to me. In the future, I want to make a hydraulic press that will be powered by this unit. In the next video I will want to show you how to make a 4 in 1 skid steer bucket and there I will also need the help of this device to show its capabilities.
The engine used in the video has a power of 1.1kW / 1.5 hp.
Pump 6L/min
Two-section distributor 40 L
Check out our previous videos
• Making Skid Steer Tracks - Skid Steer Tracks
• Making Hybrid Stump Gr... - Hybrid Stump Grinder
• Cutting Steel easier t... - Cutting Steel easier than you think - Use Wiper Motor
• Making revers trike to... - Making Revers Trike to have fun - Věda a technologie
I've developed a habit where I don't fully commit to a weld if it's something that can be welded when the project is in its completion phase. I usually just tack it in place. This has saved me a TON of time grinding/cutting if something is wrong.
Kick ass!
Great power unit. Press, crane, clamping, etc
Thanks for sharing
Cheers
Nice work, that will be handy testing hydraulic parts and systems. Have a great week
add angled edges to a circle and split logs fast and easy too ... or make planks or shingles with little effort ...
"Measure once cut twice"....Definitely been there my friend. 😅
Cut it 3 times and it is still too short..
Another great video! Thank you for taking time to build, film, edit and post this video.
Very satisfying to watch! Must be that AMSR thing they go on about! You have an extremely high level of knowledge and skill which you show in your videos, take care from the UK!
You are a wizard! Nice work!
Czy jest coś czego nie da się zbudować? Wspaniale, też bym potrzebował takiego sąsiada i przyjaciela. Wszystkiego najlepszego👍
On to pewnie by nie zbudował wszystkiego, ale jak ja zbuduje zdalnie sterowaną koparkę to już wszystko zbuduje :)
@@Progeniusz muszę Cię rozczarować już takie są. To wszystko jest takie proste po obejrzeniu filmu ale 90% by na to nie wpadła chociaż wszystkie maszyny działają na identycznym schemacie
I am so impressed with your work.
Excellent! Now make a smaller version to use as a lift on your welding table-and to turn/tilt it as well. 🤔
Looking forward to part 2. Great video-a 👍👍👍 as always. God bless.
Thank you for the dark filter when you were welding
Trudne sprawy. Dobra robota jak zawsze ❤
Turned out nice!
Thanks 👍
Μπράβο ωραία δουλειά τέτοιο μηχάνημα χρειάζεται παντού 😊😊😊😊
Fantastic work, project, and video. Cant wait to see what you do with it, very useful. Love your creativity and craftmanship.
Nice job bro 👏
Can't wait for the next part, those hydraulics are working nice! 👍💪✌
Welcome to the hydraulic press channel. Great build
Or maybe welding table press channel 😂
Love you man,great work😊
Masz fajne pomysły albo ciekawe zlecenia. Niektóre pomysły zamierzam wykorzystać. Dzięki.
Fajnie wyszlo, jak zawsze, mega sprzęcik i super film, pozdrawiam
Thanks for inspiration. Just trying to figure mine out.
Cudowna sprawa!
Good job mister beautifully done
Parabéns pelo seu grande projeto incrível muito bom mesmo
Fantastic work here!
Excelente trabajo!!
Fantastic work, dude! Really well done! 😃
I bet it's going to be really useful!
Stay safe there with your family! 🖖😊
Молодец !! Руки из плеч 👍👍👍👍👍
Cześć my friend. Thank you for this great video, I've been playing with the idea of a car elevator for months. With your setup, I have no excuses. Subscribed 😄
Respect from Romania.
I liked the end result where MiP bends sections of steel. Would this size of hydraulic pump be strong enough to squash an empty 45 gallon/205L drum?
Super. Dla nieco większego komfortu pracy polecam silnik z pompą i wszelkie elementy podłączone z nimi stalą (np. rurami hydraulicznymi) zawsze umieszczać na tanich walcowych, metalowo-gumowych wibroizolatorach.
Great stuff, as always. Cheers.
MUITO BEM BOLADO ...COM TODA SUA EXPERIÊNCIA ..TODOS OS PROJETOS SÃO FENOMENAIS ,,,,JAÚ SP BRAZIL 😊
You are wise beyond your years!!
Здравствуйте! Отлично сделано! Подскажите, а что за патрон куда крепите метчик?
Muito bom ! Tem como passar , o modelo da bomba é a capacidade do motor? .
To teraz czekam na prasę 😂😂
Ile to ma ton nacisku?
Rębak do drewna z tego można zrobić?
Great my bro, please can you tell me the type (serial number) of blade that you used. Thanks in advance.
Nice bro!
Thanks man 👍😉
Impressive guy....
Nice one ! Can't wait to see the next videos !
Хорошо работать, когда все детали имеются 👍
Always love your content. Keep it up my man. An idea I've been thinking of would be an aluminium can crusher if you haven't already made one? Would love to see how you do it.
Amazing job my friend congratulations
Thank you! Cheers!
Your work is mind blowing 😊😊😊😊😊😮😮😮😮😮😮😮😮❤❤❤
Totally awesome job
Siemanko nie wiem czy bylo, może wykrawarkę do otworów byś zrobił. Pozdrawiam!
Good tool to have.......enjoyed that - thanx
Wow, an amazing work! 👍
Hi, thank you for your videos
very talented dude
Hallo,
Was ist das für ein Bohrfutter das du für die Gewindeschneider verwendest?
Small question is the pump designed for that much rpm or does it have a short duty life ?
Very nice work, thanks for sharing
Me encantaría aprender hacer una prensa hidráulica amigo pero no sé cómo empezar me gustaría recibir consejos para poder desarrollar una prensa para trabajar 🙏👏👏
Okay, I see a new avenue of project abilities now. Wonder what he will be building next...
I revealed it in the description of the video 😉
Witam, bardzo dziękuję za film. Czy mógłbyś umieścić link do poszczególnych komponentów/części (adaptator obudowy silnika do pompy hydraulicznej, adapter łączący itp.), gdzie można je kupić, byłoby idealnie. Dzięki
Great project. Tell me, what kind of marker with a thin rod do you use for marking on metal?
LYRA 4480051 Marker for deep holes 😉
@@MadeinPolandChannel thank you!
0:05 hallo, kannst du noch eine Auflistung erstellen wo man die Verschiedene Teile kaufen kann?
Great work and great skills!
What's the rated pressure for the pump?
I think 250 bar, but the overflow valve on the hydraulic distributor is set to 180
@@MadeinPolandChannel Thanks! Keep up the good work! I always enjoy your videos!
Can you send the link or technicsl name of the connector used to connect the pipes
Po zrobieniu agregatu, w układzie sterownik dwustronnego działania coś harczy jakby w siłowniku, Jaka może być przyczyna?
Proszę o podpowiedź
It turned out awesome; did I see a leatherman charge tti+ being used?
Yes Sir. Great for everyday work.
Классно! Только бы ещё увидеть как отключаешь от системы и сливаешь масло из цилиндра.
А зачем из них сливать масло?
@@mechnomad2572 для подключения к другим целиндрам при необходимости, например. Иначе зачем там быстросъемы?
W koncu filmik, kurcze posucha u twórców na necie. Dobrze ze tu mozna zaznac relaksu.
Solda com co2? Abraços from brazil
Kosmos robota !❤
is the relief valve integrated in the valve block? have you consider to put a strainer inside the tank to protect gear pump? in general suction pipe seems not very wide, you could have some problems when oil is cold. good job, i hope to be helpful
Yes, the overflow valve is in the manifold.
A mesh filter is also used, you will see it if you watch the video carefully.
The suction pipe is not thick, but the pump is of low efficiency, so it should not be a problem, especially since the temperature in the workshop is almost always higher than 15 degrees Celsius.
@@MadeinPolandChannel ok, i missed the mesh, good job!
Meu nome é Celso Garcia, achei excelente!
Como hobby, gostaria de receber dimensões, capacidade dos componentes e lista de materiais.
Grato
13:50 cant wait for the next video. Please do it tomorrow 😁
Muy buen trabajo, qué tarea conseguir el motor y la bomba a medida , cómo así también todos los accesorios para el circuito hidráulico. Lo único que no me gustó es la corredera comprada , la veo frágil.
Daruz bellissimo video. Mi piace che tu abbia scritto in ITALIANO. Mi auguro un giorno di incontrarti per conoscerti di persona. Ogni tuo video è fonte di ispirazione per qualcuno dei miei
Thanks Great Video
Welcher Motor ist dieser 400V/3000 U/min oder 230Volt
good job friend
Very nice work! consider some of these upgrades for you fluid reservoir: Add baffles to the inside. this will help slow the fluid down giving it more time to cool and let contaminates sink to the bottom. the return line should be as far as possible from the intake for the same purposes. Also its best to have the return line slightly submerged to prevent air bubbles from forming when the fluid falls in. one more thing i might add is a magnet to catch metal particles. By the way i didn't see a pressure relief valve anywhere. it would be wise to add one especially since you will be using it as a press.
Your tips are very accurate and useful to many people. However, my hydraulic system is very simple because it will not operate under constant load and its operation will be rather temporary.
Your tips are good for larger systems exposed to longer run times and higher loads.
Regards.
nice project 👍👌
what is model yor hydraulic pomp?
i restore my press 40t, but my old pump i a very very bad
I don't remember exactly, I know it is a 6L pump
Hi sir i want to ask you what's relation between a power of electric motor and the hydraulic motor ? Or how can i chose ?
Great work you are awesome bro 👏 😊❤❤
OMG! Where did you get these offset adapters for your couplings? These are genius! 🤩
I bought them here. From what I checked, they are available in other countries, but you have to look a bit 😉
sklepdlarolnika.pl/pl/p/Szybkozlacze-hydrauliczne-mimosrodowe-euro-gniazdo-miekkie-typu-push-G38/31141
Gracias por el enlace ,y buen trabajo
15:42 wow, surprised those pins didn't shear off sooner!
I may have missed it but does this system have a pressure relief valve to drain back to tank?
@TommyTempath it might be in the Valve Body so to say, as if I am correct that sort of dual valve body has in and return, plus the 2 sets of ports. 13:13
Jest jakaś nowa strona na facebooku?
How much would it sell for on the market?
What would you call the piece that enclosed the motor to pump mating? The shroud type price.
pump bell housing ;)
Hello my friend, Nice job.
I see there are numbers engraved on the little cylinder, can you tell me the numbers please, i think it’s made by chapel hydraulique, the factory where i work 😉
what do you call those offset / eccentric fittings? i need those for exactly the same reason
I used very similar ones
summit-hydraulics.com/product/eccentric-fitting-summit-hydraulic-multipliers/
Thank you for show ing
Where did the bell housing and coupler come from? Looks like it’s all meant to be put together
You can configure the engine, bell and pump online. It's not difficult, you just need to spend some time.
Thanks. Where does it come from?
Damn nice work 👍🏻👍🏻👍🏻
Zrób jakiś domowy podnosik taki ala paleciak tylko żeby podnosił na większą wysokość i żeby można było podnosić i opuszczać wkrętarką 😎
Albo połączenie paleciaka z rowerem, aby nie targać jak jest załadowane dużo. Podnoszenie też realizowane nożnie.
Ein paar Tipps von einem Hydraulik Monteur
Unbedingt eine maximal Druck Begrenzung in die Druckleitung einbauen um Schäden zu vermeiden
Keinen Filter in die Saugleitung einbauen der Ölfilter muss in die Ölrücklaufleitung in den Tank dafür gibt es spezielle Rücklauffilter zum Einbau in den Tankdeckel
Is that two way pump
Fajna pompka. Do rębaka powinna się nadać, jak myślisz? Trochę wolno by to chodziło tylko.
Do łupania trochę za wolną, chyba że ktoś dysponuje sporą ilością wolnego czasu 😉
Приветствую, подскажите пожалуйста какие характеристики электродвигателя?
Perfect 💪💪💪
Cześć, ile obrotów/min silnik ? I czy to jakiś gotowy zestaw z tą przystawką do pompy ?
1440, zestaw kompletowany, składany z poszczególnych części, (sprzęgło kłowe, dzwon pompy hydraulicznej, pompa i silnik.
Good work ❤❤