Video není dostupné.
Omlouváme se.

How to Turn a Window Into a Door | Ask This Old House

Sdílet
Vložit
  • čas přidán 8. 01. 2024
  • In this video, This Old House carpenter Nathan Gilbert helps a pair of homeowners provide safe passage to the backyard for their children by replacing a double window with a sliding patio door and building a beautiful, low-maintenance deck.
    SUBSCRIBE to This Old House: bit.ly/Subscrib....
    What good is a beautiful backyard if you don’t have a way to get into it? That’s what a pair of homeowners faced when they called the Ask This Old House team for help. Their beautiful home has a fenced-in backyard, but to gain access, the couple’s children would have to walk out the front of the home and through a garden gate.
    Carpenter Nathan Gilbert Knew just how to help. He located a double window on the backside of the house that would be perfect for converting to a door. With the couple’s help, Nathan removed the old windows, wall paneling, and even some framing to make way so he could install a new sliding patio door. Here’s how he did it.
    Difficulty: ⅗
    Time: Several days
    Cost: Around $1,500
    Where to find it?
    To remove the windows Nathan starts by scoring the paint around the window stops with a utility knife [homedepot.sjv....]. Then he uses a pry bar [homedepot.sjv....] and hammer [homedepot.sjv....] to pull off the window stops.
    After removing the stops, remove the window sashes and the frame. Score along the paint line of the window trim with a utility knife. Use a pry bar and hammer to remove the window trim and the wall paneling under the window.
    To remove the jamb, use a combination of prying tools and a reciprocating saw [homedepot.sjv....].
    Self-adhesive flashing tape [homedepot.sjv....] provides an added layer of protection to the rough opening. Create a water-resistant seal by putting a layer of silicone sealant [homedepot.sjv....] along the edge of the flashing tape.
    After fitting the door in place, support, and level the door with shims [homedepot.sjv....]. After checking that the door is level use screws [homedepot.sjv....] to secure it. Add flashing tape around the exterior border of the door with a ¼” overhang. Add Self-adhesive flashing tape to the exterior header.
    If you have questions about your DIY door and window projects, speak with a The Home Depot associate through the Home Depot’s Millwork Virtual Apron program [homedepot.sjv....] for expert help and advice.
    Products and Services provided by F.D. Sterritt Lumber Company [www.sterrittlu...] and MP Doors [mpdoors.com/].
    Looking for more step by step guidance on how to complete projects around the house? Join This Old House Insider to stream over 1,000 episodes commercial-free: bit.ly/2GPiYbH
    Materials:
    2x6 lumber [homedepot.sjv....]
    2x8 lumber [homedepot.sjv....]
    1x6 lumber [homedepot.sjv....] (for balloon-framed homes)
    Rubber membrane [homedepot.sjv.io/GmdOLn]
    Silicone caulk [homedepot.sjv....]
    New patio door [homedepot.sjv....]
    Wood shims [homedepot.sjv....]
    Wood screws [homedepot.sjv....]
    Rubber flashing tape [homedepot.sjv....]
    J-channel [homedepot.sjv....]
    Tools:
    Utility knife [homedepot.sjv....]
    Hammer [homedepot.sjv....]
    Pry bar [homedepot.sjv....]
    Impact driver or drill [homedepot.sjv....]
    Reciprocating saw [homedepot.sjv....]
    Sledgehammer [homedepot.sjv....]
    Caulking gun [homedepot.sjv....]
    Level [homedepot.sjv....]
    Oscillating multitool [homedepot.sjv....]
    Plus, download our FREE app for full-episode streaming to your connected TV, phone or tablet: www.thisoldhou...
    About Ask This Old House TV:
    From the makers of This Old House, America’s first and most trusted home improvement show, Ask This Old House answers the steady stream of home improvement questions asked by viewers across the United States. Covering topics from landscaping to electrical to HVAC and plumbing to painting and more. Ask This Old House features the experts from This Old House, including general contractor Tom Silva, plumbing and heating expert Richard Trethewey, landscape contractor Jenn Nawada, master carpenter Norm Abram, and host Kevin O’Connor. ASK This Old House helps you protect and preserve your greatest investment-your home.
    Follow This Old House:
    Facebook: bit.ly/ThisOldH...
    Twitter: bit.ly/ThisOldH...
    Pinterest: bit.ly/ThisOldH...
    Instagram: bit.ly/ThisOldH...
    How to Turn a Window Into a Door | Ask This Old House
    / thisoldhouse

Komentáře • 98

  • @Teddybearsandkittys
    @Teddybearsandkittys Před 6 měsíci +16

    TOH is one of the all time best shows imo. Zero drama goes a looooong way with me

  • @baspluim5925
    @baspluim5925 Před 7 měsíci +79

    I can't believe how young Tom looks!

  • @user-sj1kw9yz6x
    @user-sj1kw9yz6x Před 7 měsíci +8

    Door and deck fit nicely with the house. Nice job Nathan and mark.

  • @Lawman212
    @Lawman212 Před 7 měsíci +3

    Wow, what a project. So many lessons demonstrated. Thanks very much to the fine family who had the idea.

  • @mattmcdonnell2515
    @mattmcdonnell2515 Před 7 měsíci +8

    Wish they showed the trim and bringing the siding into the new area. Really valuable areas of waterproofing the sides and top skipped right over.

  • @zunedog31
    @zunedog31 Před 7 měsíci +7

    Nathan getting the big projects. Great work!

  • @glencarolo2597
    @glencarolo2597 Před 7 měsíci +7

    As always, great job. Great opportunity to make that deck a bit bigger. Although, it is easy for me to say I didn't pay for it...

  • @jeromelerouge
    @jeromelerouge Před 7 měsíci +29

    Thought this was a video about Boeing from the title

    • @Gubers
      @Gubers Před 4 měsíci

      I think that's the one titled "How to trip out a door. Hands Free!"

  • @markthorsen2888
    @markthorsen2888 Před 7 měsíci +4

    I replaced some windows by myself for the first-time last fall. I was absolutely blown away by how easy they come out or maybe I should say how little was holding them in. Now I want to do them all just for peace of mind!

    • @degenwow
      @degenwow Před 6 měsíci

      it's forces beneath our consciousness that holds these window in place.

    • @rosea1021
      @rosea1021 Před 3 měsíci

      no wiring inside the wall underneath the window?

  • @2loco
    @2loco Před 6 měsíci +1

    Excellent job. Turned out to be a beautiful job and a great addition to the house. 👏

  • @bushworstprez
    @bushworstprez Před měsícem

    Amazing! First time seeing the PVC around the treated wood. ✌🏽❤️

  • @davedube1148
    @davedube1148 Před 7 měsíci +1

    Beautiful job. The kids are adorable.

  • @poeticthoughts06
    @poeticthoughts06 Před 7 měsíci

    Great job, Nathan and family.

  • @1wadup
    @1wadup Před 7 měsíci

    Great work, Nathan!

  • @HAMRADIOJOE4178
    @HAMRADIOJOE4178 Před 6 měsíci

    NICE, REALLY NICE

  • @phillipbaker3860
    @phillipbaker3860 Před 7 měsíci

    Great work again

  • @StuffTested
    @StuffTested Před 7 měsíci +1

    What about doing the opposite? Turning a sliding glass door (or two of them) into smaller windows? I know it's a similar process, just would like to see it done.

    • @bryan__m
      @bryan__m Před 20 dny

      Just play the video in reverse.

  • @joshuaseaton4526
    @joshuaseaton4526 Před 6 měsíci

    Get up, c'mon get down with the thickness!!

  • @jpatrick1967
    @jpatrick1967 Před 7 měsíci +6

    I love how the contractor shows up, looks at the job, and gets right to work. No measuring, no checking for structural issues, no permits. This show makes it look like everything happens really quick.

    • @dave.23.
      @dave.23. Před 7 měsíci +1

      I know side projects become frustrating for sure when you do them. A 3-4 day job here was wrapped up in 15 minutes. Then you go to do it, make mistakes, forget something from the hardware store, etc. It gets irritating when yours isn't as fast, lol.

    • @andrewk-majordochomerepair6014
      @andrewk-majordochomerepair6014 Před 7 měsíci +1

      Obviously there was a lot of prior planning and prep. Building permit had been issued and slider of course wasn't chosen and picked up on day of install let alone all the misc supplies Nathan wouldn't necessarily have off hand. Header size is typically determined by a structural engineer at time of building permit application and review... The install was quick but that happens because of his experience and proper planning. A lot of detail can't be shown due to video time constraints. Always good work from the TOH team. Great to see Nathan a part of the group, Mark, and Jen with sadly our long time TOH experts nearing retirement.

    • @82dupont
      @82dupont Před 7 měsíci +2

      He did say it was going to take a couple days and asked if there was someone to take care of the kids.

  • @holtrussell
    @holtrussell Před 7 měsíci +2

    What is carrying the point loads of the newly positioned Jack studs? Also, how was the header size calculated?

  • @acerbuergerianum8020
    @acerbuergerianum8020 Před 7 měsíci +1

    Exelente trabajo en familia! Gracias por compartir conocimientos😊

  • @rknotz187
    @rknotz187 Před 7 měsíci +8

    Surprised no temp supports when he cut that opening before the header was fully installed.

    • @Lando1020
      @Lando1020 Před 7 měsíci +2

      Caught me by surprise too

    • @larryc8568
      @larryc8568 Před 7 měsíci +4

      There were no headers originally, so removing the windows did not change any load bearing. The addition of the header was an upgrade.

    • @car45racing
      @car45racing Před 7 měsíci +1

      With balloon type construction there are no need for headers

    • @Lando1020
      @Lando1020 Před 7 měsíci

      @@car45racing thank you for clarifying.

    • @Lando1020
      @Lando1020 Před 7 měsíci

      @@larryc8568 thank you for the info

  • @teachersradio7648
    @teachersradio7648 Před 2 měsíci

    What else do we need to do if the electrical socket is right under that window?

  • @gameeverything816
    @gameeverything816 Před 6 měsíci +2

    I have no idea how they can wear safety glasses and a dust mask at the same time without the glasses fogging up in about 10 seconds. I've tried every kind of anti fog glasses, all the sprays and wipes. Nothing works. I think its because anti fog coatings just dont like to stick to plastic. I've even tried swimming goggles and the moisture from my eyes fogs them up!

  • @mollyziegler276
    @mollyziegler276 Před 2 měsíci

    If there was electical, how much harder would it be?

  • @bintoe14
    @bintoe14 Před 3 měsíci

    What was supporting the roof when there was no header installed?

  • @thomasstambaugh5181
    @thomasstambaugh5181 Před 7 měsíci

    I know it's a nit, but the video ignored how the new header was aligned with and joined to the stud ends above the window opening. Did they cut the original load-bearing stud at exactly the right place so that each of the old studs hit the top of the new header? Were the bottom of those studs screwed or nailed into the top of the new header?
    I know these guys are professionals, but I've done enough work like this to wonder whether installing that header was really as easy as the video made it seem.

  • @SarahMarks-di8em
    @SarahMarks-di8em Před 5 měsíci

    Everyone seems to always skip some of the details around the door waterproofing and/or trim work.

  • @HarrisFS
    @HarrisFS Před 6 měsíci +1

    That homeowner lady is gonna tell everyone at the cocktail party:"I picked up a hammer and help build this house" 😅

  • @akivafox3588
    @akivafox3588 Před 7 měsíci

    he makes a better door than a window

  • @mattypants
    @mattypants Před 6 měsíci

    Why not a larger decl. Would have been perfect for that space.

  • @b4lt4z4r85
    @b4lt4z4r85 Před 7 měsíci

    only suggestion, cover everything in plastic or create boxed in separate working area
    dust will be on furniture and all items
    leaving any cleaning to be done by customer is -1 point, 9/10

  • @adrastos761
    @adrastos761 Před 7 měsíci

    the sliders didn't have a screen?

  • @Joey-sq8de
    @Joey-sq8de Před 7 měsíci

    Who covers cedar with vynil siding ahah

  • @mcarroll598
    @mcarroll598 Před 7 měsíci +1

    Did you check for lead on the existing paint?

    • @kaseyc5078
      @kaseyc5078 Před 7 měsíci +2

      Ok Karen

    • @josephewing80
      @josephewing80 Před 7 měsíci +1

      Only required for homes built after 1978. That house looked pretty new, so likely not required.

    • @mcarroll598
      @mcarroll598 Před 7 měsíci

      @@josephewing80 what year was this house built?

    • @mcarroll598
      @mcarroll598 Před 7 měsíci +2

      @@josephewing80 looks like before 1978, looks like planks were used instead of plywood for outside walls.

    • @rupe53
      @rupe53 Před 7 měsíci +3

      @@mcarroll598 stone foundation, plank under siding, balloon frame, is all pre 1950. (and so was that wallpaper)

  • @TTURocketDoc
    @TTURocketDoc Před 7 měsíci +4

    I've never seen a house without a backdoor, very odd.

    • @derewreck
      @derewreck Před 7 měsíci +4

      Maybe they turned a door into a window a different time.

    • @kevin9c1
      @kevin9c1 Před 7 měsíci +1

      Super old house and maybe didn't always have a nice back yard.

  • @anonymously241
    @anonymously241 Před 6 měsíci

    Where is Thom?

  • @kamranhaidertunio
    @kamranhaidertunio Před 5 měsíci

    I am surprised at the big beautiful houses that Americans have. Here in canada we have shoe boxes with several families renting one shoe box.

  • @jlacson74
    @jlacson74 Před 7 měsíci

    Why wasn't there any back door to begin with? Weird.

  • @carolmccloud6582
    @carolmccloud6582 Před 7 měsíci

    No checking for lead paint?

  • @pavelow235
    @pavelow235 Před 6 měsíci

    Too bad they couldn't put in on the rear, the flow would have been even better.

  • @nick4leader
    @nick4leader Před 7 měsíci

    From a window to a door

  • @Bigdrawss
    @Bigdrawss Před 7 měsíci +4

    Men of culture, we meet again.

  • @tayred81
    @tayred81 Před 7 měsíci

    I don't like PVC. The feel with wood and aluminium is better. The hole house is plastic. It will last for shure 😅

  • @xjm40
    @xjm40 Před 7 měsíci +5

    Her working in the long dress..

  • @ChevyORwalk
    @ChevyORwalk Před 3 měsíci

    My only gripe is why is she wearing a dress and working on the house? My wife and I remodeled a house in our 20’s during the pandemic and sold it. I taught her to run a saw, both circular and miter, nail gun, lay flooring, cut trim, set toilets, run water lines and HVAC and she loved every minute of it. But she wore pants and PPE. Otherwise great job guys. Love TOH. My philosophy is to teach her enough that if I were gone tomorrow she wouldn’t need me.

    • @afterstars
      @afterstars Před měsícem

      Wouldn’t her new husband just do it?

    • @ShandaP018
      @ShandaP018 Před měsícem

      Yea I'm confused too

  • @awpetepete
    @awpetepete Před 22 dny

    Are ❤❤❤❤dev
    For fikr

  • @davidmuchicko6471
    @davidmuchicko6471 Před 5 měsíci

    I dont own a dress like that, can I still do this project?

  • @knowledgeispower6192
    @knowledgeispower6192 Před 6 měsíci

    And for the low low price of $12,000 this too could be yours.

  • @tinahiheels
    @tinahiheels Před 6 měsíci

    i see alot of mistakes he made

  • @Profound52
    @Profound52 Před 7 měsíci +2

    Why would they allow her to wear that outfit and no gloves?

  • @alexknight7191
    @alexknight7191 Před 7 měsíci +1

    Tom Silva he is not. Nothing against Nathan's skills, but he just lacks Tom's charisma.

  • @rl328
    @rl328 Před 7 měsíci

    Not great camera work. Way too many times where I thought would be nice to see the work that's going on instead of the workers.

  • @austinmoehring6110
    @austinmoehring6110 Před 7 měsíci

    That's got to be a first. No knowledgeable explanations or advice from the craftsman. Not what I expected.

  • @PhpGtr
    @PhpGtr Před 7 měsíci

    Jesus what a miserable homeowner. They got TOH to do their project, and it looks like he's getting teeth pulled the whole time.

    • @degenwow
      @degenwow Před 6 měsíci

      it wasn't his idea