How To Connect Your Airbrush To A Shop Air Compressor!
Vložit
- čas přidán 16. 04. 2020
- In this video, I demonstrate exactly how I go about connecting my airbrush to my shop style air compressor. Turns out it's quite simple, and only requires a couple Items!
What you'll need:
note: be sure to check the thread sizes on your current equipment to ensure proper fitment before ordering
1st: Pressure Regulator amzn.to/2W4gs5z
2nd: Plugs & Couplers amzn.to/2zD3kwo (Depends on how you choose to layout your airbrush air-line
3rd: Moisture Trap amzn.to/2VYHEma (To capture any moisture that has built up within the air-line)
4th: Shop Air Hose of your required length amzn.to/358bZmh (Optional)
5th: Airbrush Air Hose of your desired length amzn.to/3eTlGcR
6th: Airbrush quick connect/disconnect amzn.to/3cOri6f (Optional, but very useful!)
For an diagram of the overall layout listed above visit: airbrushinsider.com/connectin...
I appreciate this video so much I just thrashed my old set up it was such a headache I couldn't get a project finished
So helpful! Thanks for the tour of your setup!
I'm happy you found value from it!
Fortress.... the Harbor Freight special. I keep hearing that these little 2 gallon compressors are awesome for this application. I've even seen people attach the 7 gallon auxiliary tank turning it into a beast. Nice setup with that Neo.
Yeah, I've been happy with it. I been using it for over a year now, Maybe 2?? and its always there ready to go, no issues! Since I published the video, i've upgraded to an Iwata Eclipse airbrush, but the old fortress keeps going strong. I'll have to give the 7 gal aux tank a try!
Great video, thank you!
great video
I hear that it's best to have the moisture trap as far away from the compressor as possible, because the air as it comes out the tank is too warm (from the compression) to be liquid.
So if you have the moisture trap DIRECTLY after the tank/compressor, it usually forms moisture afterwards. Making the trap in that location useless.
Thanks for sharing your info man.. appreciate you
Thanks for the kind words friend!
Thank you!
Good video brother😎👊Thanks for sharing your knowledge.
Thanks for the kind words friend!
@@airbrushinsider7477 Yes Sir😎🤙
Thank you for the video and parts list...
Thank you for the comment!
Coolness👍
I should be able to use my pancake Air compressor. Glad I found this before I purchased a whole Air brush kit.
Yes, odds are, you'll be able to make your pancake compressor work, and it will likely work better then the typical "Airbrush compressor"!
From my understanding (I haven't actually set one up like this before but I've read about and seen many videos on the subject) the water separator should be a good distance from the air fitting outlet of the compressor because the theory is that the moisture in the air is still being carried through the hose a good distance (several feet) because it is still a vapor but as it travels through the hose it will condense more into a liquid where the separator would be more effective. Maybe even just coiling up a section of hose( 10 ft or so) and connecting the separator at the bottom of the coil (using gravity to an advantage) it should remove more moisture from the air. I have a separator hooked to my older Craftsman 20 gallon compressor like yours is here and I've never had any water collect into it and this may be why. I'll try to find a video or two and post the link in case you'd like to check them out and make more clear what I'm talking about.
correct! that's partially why i use the orange compressor hose (discussed nearer to the end of the video) when working on larger projects that will make the compressor start running hot.
Great info, thanks. I didn’t want to buy a separate compressor just for a brush.
I felt the same when I was looking to start airbrushing... Thankfully an airbrush will operate just as good, if not, better with a larger (Shop) compressor.
I did exactly that and I regret it the set up was ass
nice
Really helpful video with some good ideas. I've been looking at this same Fortress compressor. Have you been happy with it?
Very happy with it! It works great with my airbrush, and hasn't given me any trouble since i bought it. Was purchased a little over a year ago.
This is terrific-just what I needed. Very clear, patient, comprehensive instructions. I just wish that you had mentioned that all the specific fittings (including measurements) would be listed after the written introduction for your post! I found them, but only after asking myself repeatedly, "Why isn't he mentioning dimensions?"
Your totally right! Looking back, I wish I had done better with spec's... Maybe I'll do a re-make, as I have had many question that I should have answered in the video.
Thanks for your Input Chris!
Will a 6L air compressor work with a airbrush or mini spray gun
That is the best setup I've ever seen I was always wondering if this could be done Good job man! Why buy a dedicated airbrush compressor when you can use that thing and also multitask with it, what do you get the moisture trap and The quick release thing? The fitting that goes to the airbrush is that hard to find?
Amazon has the Airbrush quick coupler with mac valve so you can adjust the PSI there on the airbrush. However the one I got, I'm not a fan of. I'd suggest you get this one amzn.to/3wnrVyP I have a cheaper one but it pinches off air flow if pressed to the side?....
The quick release fittings are easy to find at any hardware store or on line it's just a 1/4" air coupler and plug.
Late to the party but I have the 1 gallon version of this. The quick connects can be found in any hardware store - home depot etc. Same with the moisture trap which tends to be cheaper and better quality than "official airbush" traps. Thing is that these tend to be 1/4" in size so you need that adapter to bring it down to accept regular airbrush hose which is like 1/8". Those can be obtained from like amazon or so. My only recommendation is getting a digital PSI reader too. The gauge on the tank itself was meant for tools so trying to set a low PSI like 20 is tricky. From there you're golden cause this thing is low pitch noise, doesn't vibrate across floor thanks to meaty rubber shoes instead of suction cups, and the dual piston motor kicks in quick filling tank up while recovering faster. I found hobbyists to be really difficult to convince how much higher quality and relatively low cost this is vs everything else.
Do you need regulator on the airbrush?
Oh what a pleasure to find a Vid without it starting with that bloody awful annoying " Hi guys whats up ".This has been Very helpful M8. Glad I found your Vid. Straight "normal" talking instead of the usual funny guy comic crap style the Yanks normally dish out .and thanks for taking the time to give the fittings also . Very helpful👍
I'm happy you found the video Helpful friend!
Have a DeWalt pancake & this will save me from buying a compressor. Thanx brother for clearing all this shit up for me.
I'm happy I can help! You have a great day David!
What are the specs of that fitting you show at 01:46, I do not know what to order? I believe it may be from 1/4 NPT male to 1/8 BSP, but I am not sure... Anyone can chime in? Thanks
Can you talk about the big problem of changing 1/4" NPT to BSPP thread? You need adapters to do so that aren't readily available in most hardware stores.
I haven't personally tried to convert NPT to BSPP, simply because I haven't needed to. So I haven't got much experience on the topic. However I'm sure a quick web search would yield a resource on the topic.
Can you use the moisture trap on the angled hose outlet on front of compressor?
Yes I could use the Angled connection on the compressor, but I don't really like the angle it puts the moisture trap at. Now when i hook my shop air hose in (between the compressor and the moisture trap) the angle doesn't become an Issue.
Have you got a compressor similar to mine?
By the way, thank you for the sub!
No I don't have a side outlet.
can we get a link to the fitting from the plug to the hose that leads to the airbrush please? thanks
Here is the fitting alone: amzn.to/36jF8w8.
But you can get the hose with a fitting for just a dollar more here: amzn.to/3wgmMa4
Or here is an assortment of airbrush fittings. (Id recommend this one as it comes with the one in the video as well as many more for just alittle more cost: amzn.to/3xnb5jf
We’re did you get the fitting to Connect to the airbrush holes
It came with the air hose. But its a 1/4th to 1/8th fitting. The air hose used in the video is a 1/8th thread. There should be a link in the description to the air hose im using. It comes with the fitting.
Can you provide a list of parts used please?
In the description, I added a list of all the items you'll need for the job, along with links where related items (to what were used in the video) can be found. Let me know if you have any other questions!
Now I just bought a compressor yesterday but after looking at the spec sheet online I saw that it said NOT SUITABLE FOR AIRBRUSH. It was just a 3 gallon tank but I returned it because of what I read. Is it possible that it said that in the spec sheet because it didn't come with a moisture trap? I REALLY want to do a set up like what you are showing but I'm really trying to do my homework on this before I find out the hard way (ruined artwork) that I should have done something first. Thanks for any help that you can give.
Huh? I don't know for certain why they would be stating that, as I have not seen the spec sheet.
Partially I wonder if they stated this because the compressor is rated for Pressure far beyond what is required for an airbrush, which can be dangerous if using for body art or makeup? Example, the compressor seen in the video is rated for somewhere near to 135psi. (to put into perspective, I don't use any more then 35 PSI, and no more then 15psi on skin).
My assumption is, any compressor that can range between 10 - 45 psi, can be made to work with an airbrush. Assuming it is able to keep a constant flow of air at that PSI.
Hope this helps.
Hi I was about to buy the 1 gal model for my airbrushing. Can you tell me how your 2 gal has worked for you over the past year? I need for it to be portable and noise is an issue. The 1 gal says it's ever so slightly quieter. Any issues or suggestions? Thanks!
I made that connection as well. I initially intended on purchasing the 1 gallon fortress compressor until i noticed the 2 gallon was basically the same decibel. So far, Ive owned it 2 years or so now, and not had a single issue. But to be honest, I think the next compressor I get will have an even larger tank. Currently, airbrushing at 30psi the compressor flips on to refill the supply tank about every 3-5 minutes. I'd prefer that gap to be longer personally, but its not a big deal. I'd suggest you go with the 2 gallon. you'll likely hit limitations with the 1 gallon if airbrushing extensively for long periods of time. In terms of portability, the 2 gallon is virtually the same size as the 1 gallon as i recall. moving it around isn't that big of a deal at all (to me that is.) Hope this helps!
@@airbrushinsider7477 Good information and appreciate the quick reply. Since my initial post, I discovered locally the 2 gal is the same price atm as the 1 gal for whatever reason. Although 10 pounds heavier and 3 db louder you're experience with the on/off cycle makes the decision. Thanks for the advice, thumbs up and new subscriber. Cheers.
How doese your airpresssue sound is it loud or not some much high decibel?
The flow of air (Air Pressure) can be adjusted via the pressure regulator, so in relation to the decibels, the air flow can be adjusted based on the pressure you need - The lower the pressure the quieter it will be and vice versa... Did that answer your question?
The Fortress compressor is rated at 60dB, which is around the same as most airbrush compressors
Is one galon compressor good enough? Up here in canada it's way more expensive, so maybe one Gallon with 0.5 hp 135 psi
I'll bet that will work. The compressor motor will cycle more often than it would with a 2-gallon or greater. But most the time when airbrushing your regulated at 20 - 30 PSI, so it will likely be a couple minutes before the compressor motor cycles again. Hope this helps.
The connector plus that came with my gun doesn't even fit. The gun has an innie screw and the plug that came with it with it doesn't screw. I have no idea how to connect it. And the adaptor that came with the whole set doesn't fit either. It's like it came with a the wrong parts to attach the gun to the hose 🥺 How do I know which plugs and adaptors I need?
This will depend greatly on the compressor you have. Here is a link to my written resource on the same topic - airbrushinsider.com/connecting-airbrush-to-air-compressor/
Maybe that will be of greater help. The trouble is, is it's difficult for me to say exactly what you need, as i don't know what equipment you have. But I'll do what I can!
Typically most struggle with selecting the appropriate fittings & couplers (So don't feel out of the loop), I'd suggest you research air compressor fittings & couplers, sizes and options. After doing so a lot of this will likely begin to make sence.
Hope This Helps!
After a quick search i am sure that i want to buy a regular air compressor instead of an airbrush compressor.
What type of components i need to connect the airbrush(fengda bd-130E) with this specific model? Stanley DST 100/8/6
Its difficult for me to tell you the exact size of fittings and so forth you will need simply because i cant physically see the equipment you intend on getting. That being said I wrote up a generalized article on the components you'll likely need to connect both your air compressor to your airbrush. (Keep in mind) Sizing will likely vary. Link to Article: airbrushinsider.com/connecting-airbrush-to-air-compressor/
@@airbrushinsider7477 I know that it's a little bit complicated to me the shop air compressor but I know also that it's the right decision!
Anyway, thank you very much again and I like very much your channel here and the site! Cheers mate
@@alxamp Thanks Alex, I'm happy you like the channel. I highly recommend using a shop air compressor to airbrush, over a so-called "Airbrush air compressor". So from my perspective, I think your making the right decision going with a shop air compressor. They are much stronger, and better suited for long use, then the small traditional airbrush air compressors.
Anyway, Good luck!
Why do my connections of the things- filter etc keep leaking air- even though i used that plumbers tape stuff. A dumb Q but how many times should i wrap the tape? I did twice Sometimes it is the simple things that stump you
I have faced the same problem. I used plumbers tape as well, I found best results if I wrap the male thread side, 3 - 5 times around. But make sure the tape is flat (No twists in the tape), and wrap it in the same direction the fitting will be threaded on so not to unravel the tape when threading on the fitting.
Then be sure to tighten it down well.
Hope this helps!
@@airbrushinsider7477 thanks!
Why did you add a link for a pressure regulator when you have one built into the compressor already?
For those that don't have a pressure regulator on their compressor. If i didn't have one on mine that functioned or that went low enough that's the one I'd get.
Its there to simply help people out, cuz you must regulate your pressure when airbrushing.
If you've got a functioning regulator that will work for down to 15psi, perfect your set, but if not its there...
@@airbrushinsider7477 Hey I really appreciate it. I thought you may need an extra regulator. Thanks for clearing that up.
CoOL....I may try this on a 4 gal compressor so I can do it all- spray paint, blow air out of my computer or fill a tire.
Do It! I'll probably go with a 4 gal compressor on the next one I get. The 2 gal I'm currently using works great, but requires a resupply about every 5min, and isn't as versatile. In my opinion 4 or 5 gal is a great way to go!
@@airbrushinsider7477 i just got the 4 gal one of these...very loud...80db ....cant be in the room woth this one sadly...swapping it for the 2gal one
@@cjadams7434 let me know what you think of the 2 gallon.
@@airbrushinsider7477 Totally love it so far have my grex and mini water trap hooked up and a separate little air gun for just blowing stuff out pretty quiet too
what size is your airbrush hose
The Airbrush air hose used in the video is 10 feet. But airbrush air hose sizes vary a lot. 10 feet works well for me.
Sorry I meant the diameter. Where do you find online the coupler that goes from 3/8" down to a 1/4" . I noticed there are links below for purchase but not sure if you purchased your fittings from there as I'm not sure how to buy fittings to fit to the smaller hose. New to all this.
Oh no problem. I don't believe I used a 3/8" to 1/4" adapter. the plugs and couplers used in the video are all 1/4" thread (The Plug & Coupler kit in the description should have all you need. Its not the exact kit i used because i already had plugs and couplers laying around the house. Though the specs are the same as the ones I'm using).
Now there are different plug and coupler types (Read this article: toolguyd.com/quick-guide-to-air-line-couplers-plugs/ for info on plugs and couplers).
The airbrush air hose i linked to in the description is the one I use and it comes with a fitting that will allow you to thread on a plug as shown in the video (To which the plug will be plugged into the coupler). But for some reason color of the hose varies. They display a blue one, but i got a black one. Not sure why? (The hose thread size is 1/8")
But that hose comes with the fitting needed to thread on a plug. The fitting is a 1/8" male to 1/4" female adapter.
Here is a link to an adapter on amazon: amzn.to/3bwtONB .
Though its kinda expensive when purchased by its self, and you run a slight risk of it not fitting properly. I'd suggest purchasing an airbrush air hose that comes with the adapter.
What airbrush are you using?
Because different airbrush models take different thread sizes other then 1/8". Though 1/8" is very common across Iwata airbrushes and many other brands. However I believe paasche's airbrushes take a smaller thread size.
I hope this helps, If you have any other questions reach out!
Is your compressor a 3/8 fitting or a 1/4. Because I'm not sure if you can even downsize? Oh god I'm such a novice.
No worries!
Not sure what your asking? Has your compressor got a coupler on it where you can attach a plug (like the two hookup points on the compressor in the video)? If no, and you need a coupler for your compressor, then It could be either a 3/8" or 1/4" it depends heavily on your compressor.
I"m sure here on CZcams you can find a video explaining how to measure thread size. That will help you understand what size you need. Whether it be a coupler or adapter you need.
It may be best for you to go to your local hardware store and pick up the items you need. Its easier to understand what you'll need when you can physically piece everything together. (Just do your research before hand) And you can always ask those working at the store for help.
Its just hard for me to understand your situation because I can't see what your working with.
Sorry I can't be more helpful.
I did write up an article on connecting an airbrush to a shop compressor here: airbrushinsider.com/connecting-airbrush-to-air-compressor/
Maybe that will provide better insight on your situation then the video did.
Brojects?😳
Jman
I have it set up how you do but when I press the button on my airbrush I have nothing can anyone help???
Are you not getting air?
If no, make sure your pressure regulator (On the compressor) is not completely turned down to zero (As this will not allow air to flow through the line). Also ensure you are using the correct Plugs and Couplers. There are different styles available and can not be interchanged (Example: Automotive plug will not work with a Industrial coupler). If you don't find the issue at that point, try turning on the compressor, setting the Pressure regulator to something like 10PSI (Very low) then start breaking apart each section of the air hose starting from the airbrush end. If you begin to get airflow out of the hose at any one of the break points you know that from there back to the airbrush must be a plug.
Hope this helps.
@@airbrushinsider7477 thanks I did exactly that and it worked I had a fitting that was too tight I guess bc I loosened a tiny bit and that did the trick
@@bankh.o.e7698 Awesome! Happy you solved it.
@@airbrushinsider7477 one more quick question while I have you. Fine lines with no overspray? Any tip?
@@bankh.o.e7698 You need your paint thinned out quite a bit, and try to keep the air pressure down (EX: around 20 - 30 PSI max). Then slightly pull back on the trigger , with the airbrush close to the surface while brushing across the surface. Com-Art ( amzn.to/3BCmlL5 )airbrush paints are great for fine detail / fine lines. At worst they will teach you the correct consistancy paint needs to be at for fine detail, as they do not require the addition of reducer.
If you are concerned with water in the line, do not buy a compressor ( unless you live in Arizona ), rent a cylinder filled with nitrogen from your local welding supply - zero water! ( I have been airbrushing since the mid 70s ! )
Thanks for the advice!
The moisture trap is there as a precaution. To be honest I think I could get away without it. Now that being said I airbrush at a consistent 65°F with the compressor by my side and the compressor doesn't get to hot.
@@airbrushinsider7477 No problem. Another nice feature about using a cylinder is NO NOISE - just the hiss of your airbrush or the whine of your Paasche AB airbrush's turbo!
What are the connection sizes???? 3/8, 1/8, 1/4 WHAT???
- 1/4" npt male & Female industrial plug's & coupler's. amzn.to/3Xji3TO
- Airbrush hose is 1/8" female fittings on both ends.
amzn.to/3OndKmj
- Air line side of the airbrush air hose is an adaptor = 1/4" female to 1/8" male.
amzn.to/3tI8pfE (Some hoses come with this fitting)
Dude. Right at 1:48. What is the adaptor that connects quick connect nipple to airbrush hose. Whatever that is, it’s the one and only non-obvious and most crucial part. What is it!??? Link to everything else except that. You cannot do any of this w/o that adapter…. Si what is it!?!?
Watched 5 other vids of the same thing and everyone else neglects to mention that single most crucial part. What is it??? ..thanks
Right at 1:48 is a 1/4" female to 1/8" male adaptor.
amzn.to/3fv5Dnz
Not that helpful, nothing about thread types or sizes, just a bunch of talking.