Thats not a crack ,do you actually think a machinist would have reground a cracked crank ? And when diesels "crack" a crank they are removed in 2 pieces because they literally break in half
@@golfin.d1081 I didn’t see the use of an torque angle gauge. While I’m at it, why did you put oil on the backside of the main bearings ? That is due to a popularly held myth and a time waster at that. That is like one older guy I witnessed putting axle grease on the head gasket before final assembly. The crank rides on the other side, which, a bit later, you finally did put oil on the side the crank rides on. I wonder how many engines come “back” because of issues such as these.
@@jimmywaters3987 i didn't see what are you talking about, when he put oil backside of bearing ? And torque angle procedure not always using torque angle wrench, they can using paint marker for do that
На восьмой минуте начинает крутить, если я не ошибаюсь и в руках динамометрик. А потом просто доворот на 90. Думаю что халтурщик "пятном контакта" мучить себя не стал бы. Затянул бы сразу трубой и в сторону.
Difiero de tu procedimiento. Para esta prueba de plastigauge con el cigüeñal, el cigüeñal debe de estar totalmente seco para que al final de la prueba y medición de la tolerancia sea la correcta. Fake!
Nota : no se debe poner aceite bajo el cojinete..puede girarse..al contrario debe estar limpio y seco..
Show de bola queiria muito fazer parte dessa equipe parabéns
Semangat terus pak selamat berkarya.💪👍🙏
He didn't seam to put much oil on those main bearings.
ایول دمت گرم چه موتوری جمع کردی
👌👌👌
OK like
Outstanding workmanship.
Да ладно не знал что под коренными не мажут это же целое открытие, а когда пальчиком помахал так вообще гений!
Почему не мажут?
Все он правильно сделал. Где надо смазал. Это ускоренная съемка, малозаметно. у нас то умельцы мажут вкладыши с двух сторон 😂и мнят себя профи
Bang mau nanya untuk baut flywheel ukuran Torque wrench brp Nm ya? Engine D85e-2
Kekencangan baut torsi timing gearnya berpa kg ya mas
Sangat bermanfaat. Lebih bagus lagi ditambahkan keterangan tightening torque dengan tulisan atau suara.
Makasih masukannya
@@tukangmechanic siap. Biar penonton lebih betah dan selalu kembali ke channel anda.
Berapa clearance main bering bila di ukur menggunakan plastic gauge pak ?
Amazing
Sangat baik .❤️❤️❤️❤️
Ох мастера. Чуть наоборот коленвал не установили.
Sempre olio sotto alle bronzine prima dell'albero a gomiti!!
False, the right way, always keep the bottom side of the main bearings DRY
And lubricates the bottom side of the big-end bearing
Ssiip pak,,
Thanks 🙏
👏👏👏🌟👍👍👍👍
Bro that engine is worth 50x the torque wrench.. get one
Хорошая работа 👍👍👍
No lube????
1 2 3 4 .தமிழகத்தில்.
Install Crankshaft habis Under size toch.....
👍❤❤❤
Почему масла мало налили
Así respectiva tolerancia el jirodel cigueñal
Anyone else see that huge crack in the crankshaft😂😂😂
Where at?
Thats not a crack ,do you actually think a machinist would have reground a cracked crank ? And when diesels "crack" a crank they are removed in 2 pieces because they literally break in half
140
Biasanya klo sdh pke kunci momen itu sdh trakhir pas pngencangan bautnya pak..
Tidak semua pengencangan baut seperti itu,ada beberapa yg menggunakan tambahan derajad,ikut service manual
Kalau pernah buka shopmanual komatsu,pasti nemuin setelah pengencangan baut mengunakan torquwrench,ada tambahan pengencangan 45,90,120derajat
@@golfin.d1081 I didn’t see the use of an torque angle gauge. While I’m at it, why did you put oil on the backside of the main bearings ? That is due to a popularly held myth and a time waster at that. That is like one older guy I witnessed putting axle grease on the head gasket before final assembly. The crank rides on the other side, which, a bit later, you finally did put oil on the side the crank rides on. I wonder how many engines come “back” because of issues such as these.
Многие двигатели сейчас после ключа ..идет доворот на 90.гр.и даже пара..по 90.и
@@jimmywaters3987 i didn't see what are you talking about, when he put oil backside of bearing ? And torque angle procedure not always using torque angle wrench, they can using paint marker for do that
Nt855 Cummins
Масло экономите, что не есть хорошо! А где момент затяжки с помощью динамометрического ключа? Одним словом деньги на ветер!
На восьмой минуте начинает крутить, если я не ошибаюсь и в руках динамометрик. А потом просто доворот на 90.
Думаю что халтурщик "пятном контакта" мучить себя не стал бы. Затянул бы сразу трубой и в сторону.
No offence. I noticed that you are an apprendist, if i am not mistaken.
I just 2 days as mechanic
When you instal cap bolts, always oil them also on the washers. 👍✌
@@lorenzotrevisani4421 I already put oil on them but not record
Rogério Sergio De Oliveira moro no Maranhão cidade buriti bravo
Sudah di ikat knapa di lepas lg.
Tujuan nya apa ya?
Pengencangan pertama ,kita kasih plastic gauge buat liat clearance main bearing
@@tukangmechanic 👍
klo buat mbl grandmax clearance nya sberapa nilai nya pak?
I have 12 years experience Damansara Diesel services Malaysia
Itu engine S6D125 kah bang
Видео ни о чëм(
Перед измерением .масло лить нельзя !!!!😡😡😡 no oil
Difiero de tu procedimiento.
Para esta prueba de plastigauge con el cigüeñal, el cigüeñal debe de estar totalmente seco para que al final de la prueba y medición de la tolerancia sea la correcta.
Fake!
Did you happen to see the clearance they run ? That little bit of thin oil didn't make enough of a difference to worry about
Эта.музыка.не.втему.это.хорошо.танцнвать