Replace Fuel Injector Connector
Vložit
- čas přidán 7. 08. 2024
- Show how to remove a broken fuel injection connector and replace. Even if you are unable to remove the connector from the injector will show you that too.
Amazon Associate
Fuel injector Pigtails amzn.to/2szAwOI
50pcs Solder Seal Wire Connector, Solder Seal Heat Shrink Butt Connectors Terminals Electrical Waterproof Insulated Marine Automotive amzn.to/2HTgxEe
Facebook / martinbuilt-2351766611...
#martinbuilt #jeepgrandcherokee - Auta a dopravní prostředky
OMG!!! Martin, I just wondered if this type of video existed. I did the injector replacement job yesterday, broke some connectors. Now I know this is the way to go. Thank you.
Useful part starts 4:10
Thanks Martin your video helped me out. Now I can put new connectors on my truck. Appreciate it.
It looked easier to use the pick than to use the tab that is meant to release the connector in the first place. Great video
Well, geez. After a day of looking for the correct size female metal actual pin, these are ev6 injectors and just buy some pigtails online. The learning curve of not being an experienced tech is tough some times. Well, thanks for making this video so I can now move forward. Bravo!
Thank you for watching i'm glad you found it helpful.
Thanks for this video 2nd video I watch from your channel, a day after I freaked out 😅. You do a really good job at explaining.
Great video. You made a complicated job simple for this back yard mechanic 👍👍
Glad you liked it.😎👍
All the Do-it-yourself videos this was probably the best one I have ever seen I'm not kidding you some people put garbage on here this guy actually did at true to cut video of how to replace your pigtail on a fuel injector perfect my only problem is i drive a Ford f250 v10 6.8 and a couple of the pigtails are badd towards the back of the motor and I'm not sure how i even have Room to go back there and do that that is going to be a real pain in the you know what anyways great video....
Awesome video Martin, thanks
Thanks for sharing. I have the same issue on a different brand of vehicle but your video gave me some ideas!
you helped my sprinter repair here in the UK, thank you 👋
That's awesome I'm glad you found it helpful.
Nice job Martin....
Awesome video man, thanks a bunch
Nice job, good information to have.
Finally found what I’m after. Got a stuck connector on crd fuel rail. Haven’t broke it yet!
Glad you found it helpful.
Id think the engineers would have thought about this. Should use free floating clips so when they break its not the connector housing . splicing is a pain. Thanks for the info
No need to splice the wire. You can just change the plug itself and keep your current wiring
Thanks so much for the help with this video. Do you think I’ll be OK if I put a little extra solder on the lines?
Thank you
Very helpful, thanks for the video.
I kinda knew this but thank you!
Fabric tape for the wire wrapping works best and won't come off from heat.
did you have any oxidation problems with the solder? Someone was saying with heat and vibration soldering fuel injector connectors can be a problem in the long run
Anthony Merc I've never had a problem with any of my soldering having any type of corrosion or the solder failing. If the connection fails at the solder joint then it was improperly soldered (cold solder joint)
Thank you Martin! this video was really helpful to me !
You're very welcome!
Csn i use heat tube isntead of solder?
thanks! do all connectors work with all fuel injectors/ are the styles all interchangable or will some style connectors just not fit on the injector? thanks!
most manufactures from 98 and later use the EV6 style connector.
Hey am having problems in my dodge charger v8 with misfire in cylinder 2 . how do you change the wiring injectors
Very good job!!!
Hey Martin , I found a set of those heavier duty ev6 connectors for my 02 Dakota 4.7 rebuild and in the process of soldering them in. One question, does this really change the resistance enough to throw codes ? I’ve read some people saying that and others say it’s a none issue if soldered correctly. Thanks again
There is no added resistance or enough to throw any codes I can guarantee you that.
I've done a wire tuck on this engine where I had to resolder every fuel injector connector and never had an issue whatsoever.
@@martinbuilt awesome glad to hear that. Thanks I really appreciate all your videos helped me out a ton. Take care
We'z all bakin out in scarryzona
Great video
Glad you enjoyed it
I got new injector connectors with pig tails, both wires are white.
My factory connectors have black and red wires.
How would you attach the new one with 2 white wires to the black and red wires?
Thanks in advance
You'll need to hold your new pigtail with connector next to your old connector and match wire for wire left to left, right to right.
@martinbuilt do you have a video on your ram air set up
Dustin Mittel
I've been working on it for a week or so I hope to have it out this weekend. I went and bought another silencer box so I could show you all how it's done so I'm basically building another one. With some revision changes.
martinbuilt awesome thanks
I absolutely know nothing about wiring, but just wondering, is it safe to do this? Would doing this causes higher probability of having a short in the future?
I have a
2000 dodge dakota 4.7
What fuel injector pigtail should I use?
In 1999 pretty much all manufacturers went to the EV6 connector
Thank you for making this video, Sir. Is there any way to separate the wire from the connector, without cutting and soldering?
Yes you can unlock the terminals and pull them out, this sometimes requires a special tool.
@@martinbuilt Thank you!! Subscribed!
I got kia rio one side number one injector not working but if I swap wire it work. Simely number one wire is not ryt
Thank you! Is it safe to use soldering? won't it suffer due to heat from engine?
Yes, it's o k to use solder.
It takes at least 450 degrees for saturday to begin to melt.
Thank you for watching.
Hi, my jaguar keep shut off the pump, I had the fuel injector change, but it is done the same thing?why help me??Please
Forgot to mention, ohms on injector are in spec.
Well what if my tabs are fine but my nubs are broken off?
Solder? How about de-pin the current connector and use the pins in the new connector? Less long-term problems, at least heat-shrink was used.
So what if the wires are completely different colors, how would you know which is which, you said getting the wires crossed would damage the injector....
Look at the connector and you'll notice that there is a number 1 and 2 for each wire on the connector. Match that up with the one you're changing.
You may have to look very carefully at the connector to find those numbers but they're there.
Hi Martin. I"m in Houston, TX" sorry I'm so far""_
I got different injectors which require different connectors (not allowing me to match the connectors up when wiring) and my new connectors are not color coded. How do i figure out how to wire?!
They have pin out numbers on the face of the connectors . Just match up the numbers. 1 to 1 and 2 to 2.. did this on a 4 wire connector....
Hey Martin, Sorry about posting this here. Haven't found a good way to contact you yet. :) I wanted to ask if you have a ground wire going to your Alternator? If you do, are you able to take a picture of where it is located? If you can send me a picture if you have one that would be great.
Chris Ogaz no there's no ground wire fastened to the alternator.
Ok. Thanks. Thought I might have missed something when connecting everything back up. Looks like I just have a bad voltage regulator then. I was hoping for something more simple. :) Not like its hard changing the PCM but I would rather not have to.. Have a great day.
Chris Ogaz
Yes you should only have the positive cable coming from the battery. Then one connector on the back of the alternator with two wires. I hope it's not your voltage regulator because that is inside the ECM. Those are considered a very good and not prone to going out
What can happen if plug them back wrong way
I don't think it would do any damage to the ECM I'm sure it has fail safe's installed for that it would simply not operate that injector.
Hi, my jaguar type keeps shutting - off the pump --it Is not full of gasoline --why??? thank-u
the pump will only run for a few seconds with ignition on and engine not running.
So is splicing bad or just not the best way
I don't believe splicing is bad as long as the splice is soldered. Best case would be to remove the terminal from the broken connector and reinserted into a new connector.
I don't believe splicing is bad as long as the splice is soldered. Best case would be to remove the terminal from the broken connector and reinserted into a new connector.
The wires reinsert easily?
why not just replace the connector and keep the wiring and terminals?..
Very nice job. Too bad you made the soldering look way easier than what it is lol . I’m tempted to try but the area is tight
Thank you, well it is something I do for a living. Like when we were building the T-Mobile Arena in Las Vegas I soldered over 500 mic lines which is over 1500 wires you tend to get pretty good at it. So I enjoyed soldering instead of using any type of solderless splice. If you're able to Tin the wires before you actually join them together this will help make it easier to solder them together
Think I could do it with a cheapie solder gun ?
@@levicallis459 yes I think you would be able to. Ill-health if the cider that you use is very fine engage. If you have any flux that will help as well
I’ll give it a try
Hi, where are you.i'am in Houston, TX? I need mechanic..
I'm in Las Vegas
every splice introduces 7 ohms of new resistance.
can you just remove the original wires & push them into the new clip?
Doorran....what should be done to avoid that or any better options?
Info?
It is really shame that they use this..surely there is a better way to design..
I guess it’s up to viewers to
guess what the hell he is working
on.Nothing in the title.Nothing
in the description.Only when he
finally talks and verbally says
make /model do I know what his video
Is about.
Wasted time waiting on it
Obviously you didn't bother to even look to see if there was a description because it most certainly tells you what's going on.
Thank you for watching.