How to replace immobilizer EEPROMs
Vložit
- čas přidán 5. 09. 2024
- If your vehicle is equipped with an immobilizer system, and you replace your ECM you must either reprogram the ecm to work with your existing keys, or buy new keys.
with us no need to do that!
thanks to qcwo.com and OtherDeal.com
Great from sae sedanten, indonesia
I wan ask. . I have toyota grand avanza car 2017, i just changed the ECU, the car cant start and the immobilizer indicator doesn't flicker either. What should i do? Thanks 🙏
I have Toyota Camry hybrid 2007 with smart key. EEPROM IC not able to locate and IC number entirely different. Please can you help me out
I need help with my Mitsubishi Montero xls 02. The immobilizer don't let me start it up the engine!!
This is horrible information the chip you want is in position ic900 chip 93c56 and why would you solder off the 93c56 you can reflash the eeprom on the board. Please don't try this unless your experience at soldering onto PCB. Call a locksmith or risk destroying your ecu
You're correct with the if you don't know what you're doing, let someone who is experienced do it but this is a Rav4 module. The AT25080 chip in the IC1003 position is the correct chip to eeprom or replace.
I have a Toyota Corolla s1zz engine control problem how to resut that
thanks
3:30 Anyone picture this robotic voice saying "dumbass" after the part about putting the same eeprom in that you took out?
I'm doing a engine swap on 94 4 runner butt want all my gauges to work .can I take certain pins out of ECU &take out engine wire harnes
What do you mean by pins? When swapping your engine you should not be changing any computer on a 94 4runner unless your changing to a different size newer motor. If so good luck make sure you swap wire harness, computers, cluster fuse boxes. Ac control unit, your best bet is to either make your new motor cluster fit or buy and aftermarket that can be wired in and precoded with eeprom for mileage, I'm assuming your swapping transmission as well make if its standard stick shift will be fine if not your new engines computers will have shift points programmed in so you must not keep old automatic transmission.
@@3babyghost hi have installed a toyota 3sz motor in my starlet. the motor i bought from scrap wit wire harness and ecu.
i am unable fire up the motor. can u help
i20 petrol Ecm repair video plz send
Olá tudo bem? Sou brasileiro e estou com uma Toyota Rav4 ALL keys lost. Mas não tenho suportt para reset ecu (engine Control) vocês teriam o arquivo de reset para essa soic? Sou chaveiro profissional
Minha ecu é exatamente igual a deste vídeo. Se tiver o arquivo de reset ou bypass desta ecu eu posso gravar com meu gravador de eprom
Transmission box Toyota RAV4 2002
i lose all my keys ?? can you help me???
+NORA TIFF witch car?
+NORA TIFF witch car?
I have 02 ML 320 start error code , changed burned body control module due to roofleek driped right above the emergency brake on it !!! I bought on ebay same part # A1635457332 and took it to dealer ,payed $184 for programing BCM and still not starting I gave up to pay other $200 to program key or deal with steelership ....anybody has solution below $500 ? Now thinking to buy ECU ,Bcm,key ,tubler and sender of ebay .....did anybody do it ??..... would I be ok without reprograming in steelership tro start the car if all of it is changed from diffrend car ???? Thanks
Petr Drbal no sir do not do this depending on the model you could have up to 25 pre coded computers on the car, if you bought a new bcm comfort module eeprom must be used to read the old eeprom chip from the damaged board then wrote into your new bcm eeprom chip after completion your car will not know a bcm has been replaced, although included in the read and write should be vin, pin code, key value. Original key will work
Hi
This upa cable is helpful: czcams.com/video/GSQQCA3lcOU/video.html
l9⁸