Creality Falcon2 Pro Review from a Beginner Laser User
Vložit
- čas přidán 24. 07. 2024
- Let's take a look at the Creality Falcon2 Pro 22W laser cutter and laser engraver. This is an impressive fully enclosed laser that offers excellent process control and a variety of features that are likely to impress beginners and intermediates alike.
LINKS TO PURCHASE CREALITY FALCON2 PRO:
US & CA: s.zbanx.com/r/U8ODO2Fz9cMO
EU: s.zbanx.com/r/eV5wbz84HORw
UK: s.zbanx.com/r/bxyNg1926v5S
CHAPTERS:
0:00 Introduction
2:24 Unboxing and assembly
10:44 Connecting the laser to LightBurn
13:00 Calibrating the camera in LightBurn
17:00 Laser cutting and laser engraving with LightBurn
23:38 Benefits of the Falcon2 Pro
27:29 Shortcomings of the Falcon2 Pro
31:56 Final thoughts on the Falcon2 Pro
For more content on the Creality Falcon2 Pro, check out the official CZcams page here: / @falconlaserofficial
Please note that the Creality Falcon2 Pro was provided free of charge by Creality. Affiliate links to purchase products from Creality are provided and I may receive commissions for purchases made through those links. The views expressed in the video are my own and I was not compensated to give positive sentiments.
#crealityfalcon2pro #lasercutter #laserengraver - Jak na to + styl
Great overview! I just purchased one of these off of Amazon just before Father’s Day at a fantastic price, just over HALF of the price you mentioned. Finally got around to putting it together this past weekend and still have to get it calibrated and tested. Your video was extremely helpful with laying out my next steps. This is my first laser cutter/engraver.
That’s great to hear! Enjoy.
I like the wide table under the lumber rack with the osb splash on the wall. Laser is fun. One day maybe.
Thanks! Built that table so that I could have a long drawer for a bunch of my long accessories.
@@MasonWoodshop Aye. My TSO guides are in the foam box they came in because I can’t find a safe spot.
@@FearsomeWarrior Ha! My drawer houses my TSO parallel guides as well as some UJK stuff and Benchdogs fence.
Cheers for a really great and informative video!
I'm considering getting one of these, can you tell me if it's possible to swap 'panel A & B' so that the exhaust will be on the right side?
I assume that the fan and hose connector can be mounted on the other side, but what about cable length etc., will they still reach?
Thanks in advance
Thanks for watching! The two side panels can be swapped to reposition the fan (both have the same fan control and USB cutouts), HOWEVER, the provided fan cable is not long enough to reach from the right-hand side to the fan controller. It does seem to be a somewhat standardized connector, so I wouldn't be too surprised if extensions could be found somewhere online.
@@MasonWoodshop Thanks for the quick reply! Not a deal breaker for me, but I will have to extend the cable then if/when I decide to buy one. I guess they're trying to keep the cost down, but surely there must be more people than myself who need to place it close to a wall....
Oh yeah! It’s strange that they made the panels swappable (although maybe that was just an accident) and didn’t provide a longer cable. It is really nice being able to put the Falcon2 Pro right up against a wall behind it whereas my xTool S1 has all of its exhaust and ports at the back, which is a little annoying.
Thanks for the review. Did you manage to test the 40watt 20watt feature of it?
Unfortunatelty not. The one I have is the 20W version.
Hey man, I'm looking at one of these but I can't find out the height constraints on the engraving area, and if it'd work just... without the tray if needed.
Nice review, good to know about the SD card!
Good question! I just removed some slats and with the tray in, you could probably cut material 50-60mm in height, depending on the focus spacing needed. You could remove the tray to gain another 8-10mm and there are also risers available that can lift the whole thing up. Note that with the tray removed and/or risers in use, you'll want to make sure you wear the provided safety glasses to protect your eyes.
@MasonWoodshop amazingly detailed, helpful, and rapid answer; thank you! You even snagged a follow-up I hadn't thought of, which is if the risers worked with this machine. Finally, thank you for being safety conscientious in your recommendations.
Following your channel, as im very impressed with your engagement and rationale.
@@kaeotamy pleasure and thanks for watching! These lasers are a lot a fun!
Between this laser and the S1 20w which one would you choose as a beginner?
For a beginner, I’d recommend the S1 with the main reason being the XCS software. For someone that wants total control of the laser (either experienced or a beginner wishing to learn), the Falcon2 Pro is a good choice.