Mitsubishi Front Wheel Bearing No Press Needed!
Vložit
- čas přidán 16. 06. 2024
- 2018 Mitsubishi Outlander Front Wheel Bearing Replacement (Using A Hub Tamer) Easy Procedure No Press Needed!!!
If You Found This Helpful Think About SUBSCRIBING To The Channel And Check Out Or Other Videos - Krátké a kreslené filmy
![Wheel Bearing Replacement - Part 1 [2002 Mitsubishi Lancer]](http://i.ytimg.com/vi/fvCH4wAWEt0/mqdefault.jpg)
Very clean working wow nice vedio❤❤❤❤❤
Thank you
Nice clean vid by the way👍
nice video
Great video and good info thanks
Thank you
Can you use the same press tool used to press the bearing, to press the hub into the new bearing??
Absolutely
Where do you get / buy the Hub Tamer / bearing press removal tool? Part number would be helpful. Thanks!
Harbor Freight MADDOX Front Wheel Drive Bearing Remover and Installer
How do you remove the axle so easily? Mine is stuck it won't come out. Any recommendations?
Almost no rust on this vehicle made it super easy, you can put the axle nut on a few turns and use A dead blow hammer to try and push it out of the hub. You could also try a center punch in the middle of the axle shaft with a hammer just be cautious to not damage the threads on the axle.
Part number hub bearing
Think it would it be easier to just replace the whole hub assembly?
Unfortunately this requires a press bearing and hub no hub assembly for parts on this style.
Not all car has the complete hub assembly available on nearby market.
I think that nut that goes to center/axle is wrong because since there is no whole thu axle you can't put the pin thru???
2 styles of axle nuts one that requires a cotter pin and others that are self locking.The locking nuts are very common on these newer models vehicles. Basically the outside threaded portion of the nut is not perfectly circular and really grips the threads when tightened down. No issue here.
How did you get the bearing race off?
A little heat and a chisel or carefully make a cut in the race and use a chisel to split it. If you access to a oxy acetylene torch you can heat and spin it off easily. If not the cut and split method is generally the easiest for a DIYER. Just be careful not to cut into the shaft of the hub.
You should include any torque specs you use.
Dude already gave instructions to doing it without a freaking press get a life
@@wyelandlebeouf7202 What are you 12yo. I was a mechanic for 7 years. Do some research before making a snarky comment. Without the proper torque on that axle nut, the bearing will fail.
@@justapile4376 You were a mechanic for 7 years? Then, why didn't you simply comment the torque specs? The guy in the video used a torch, but you didn't suggest he include the type of gas he used. What are you 12?
@@32Clinton32 I could have. But I get the impression that it would have gone over your head.
ugga dugga
How did it sound before replacement
Slight Humming noise while driving.
Do the new bearings come with that little horseshoe locking pin, and if mine didn't, and the old one was broken can I get another one? Also I didn't see you put that on (the lock pin). However Im assuming it's fairly simple to pop in there, do you pop it in after you put the bearing in the knuckle, but before you put the hub in the bearing?
Depending on the brand bearing you purchase yes it may come with a replacement so just check when shopping for your part. If I skipped that step my apologies the retaining ring will go on right after installing the bearing into the knuckle and right before installing the hub.
Thanks, I work on all my own stuff, not because I'm a machanic, but I just don't have the money. So I often have questions. However, alot of people don't usually answer your questions, so again thanks man.
@@James-ju1el Completely Understand!!! No problem at all any time!
Im not a mechanic, but I think you never put grease on pressed surfaces as the bearing may spin
only if the bearing is already frozen solid and fully seized. Once it's in place the grease film breaks down and it/s there until you press it out again.
You must lube the contact surfaces when pressing in a bearing to aid in proper fitment. Any residual lube in that area will not cause slippage but it will reduce the chance of moisture ingressing to the area and causing rust.
Where can i rent buy tool?
For DIY Light Use Harbor Freight Sells a Maddox Brand, It Was Actually The First One I Had I Ever Purchased The Kit Help Up Pretty Well Considering It’s Lower Cost.You Can Also Call Around To Your Local Parts Stores To See If They Offer A Hub Tamer As A Loan A Tool.
I thought your titie said no press
A Hub Tammer Is Not A Press. At One Point A Hydraulic Press Was The Standard Practice For Removal And Install Of Wheel Bearings And Hubs. This Video Shows The Replacement With A Hub Tammer That Can Allow The Removal And Install Of A Wheel Bearing On Or Off Of The Vehicle, Per The Title And Thumbnail Picture Of The Video That Shows What A Press Is And Looks Like Marked With A Red X There Was Never At Any Point A “Press” Used For This Repair.
This Is The Alternative Method And Most Commonly Used Tool When Not Using A Press.
Can you please talk less and just show us how ?
In under 20 minutes I can save you hundreds on replacing a bearing your self. Really talk less??? if 20 minutes of your time is more valuable then the money saved take it to a shop to get it fixed!!! Everything said covers the information needed to properly do this repair!