Video není dostupné.
Omlouváme se.
PE error LG top Loading washing machine jetspray Smart Inverter 8kg
Vložit
- čas přidán 19. 02. 2021
- *Water level sensor switch defect.
*May be soap powder or lints clogged in the switch hose..
*changing pressure switch...
Please watch our food food channel for delicious food and sweats..
• How to prepare Belgaum...
You’re the first one to actually show what should be done. Thank you.
Thanks! Tried it and the washer is back on duty! Excellent easy to follow instructions. Congratulations!
Great to hear!
Sir,LG washing inverter direct drive, intermittent drain ang PE error?what is the possible deffect sir?or aby suggestion thank you ❤
how much would be the pressure switch cost?
The same machine hang with air dryer and spin buttons on. How to correct?
Thanks you bhai
Welcome...
Sir lg ka 7kg topload machine hai PE show ho raha hai supply chek kiya to 2۔7 dono side aa raha hai pressure sensor ka creativity bhi aa raha hai ab main kya change karu samajh nahi raha
Thank you t worked 🥳🥳🇱🇰
Good info
Glad you think so!
Ek ment apsa bat ho sakti hai kia
Thank you I will try and comment u
All the best
How to remove the back cover.unscrew it but it difficult to open
After removal of screws release the rear side cover lock with the help of flat surface screw driver...
Lmaoooo in my case there was a mouse xd
It worked, thank you.
Glad it helped
I can't open it
It work
Sir my LG top load machine some time it's on some time off, is there any problem in wire plz suggest
If it works properly after turnon itself, then surely there is some loose connections between mains wire and wall socket.
Check the wall socket and switch.
open the back panel of washing machine and check mains wire connector.
Clean the connector pin if any rust. Press and hold the connector and check for continuous work.,
cut and change the plug pin
Hope it may work properly....
Kitna hai rate pressure switch ka
Around Rs 300 to 400
Can we clean it whitout buying new one
Before thinking about replacement, pullout the sensor switch connector and clean the switch pins and connector for the rust. Mostly there will form a rust between the switch and the connector. Clean the thin pipe which connected to the tub for blockages. I hope it will help you. Thanks for your comments...
Sir plz reply even after changing pressure switch its won't work again its shows like pe
Madam... Please check the pressure switch 5mm tube which connected to tub for blockages...
Remove the tube and clean it... There is a possibility of blocks of detergents.. Or lints..
After removing ttub side tube, fill half tub of water and check whether water comes out from pressure vent or not... If water comes out normally then tub condition is ok... If water blocking then need to clean the air vent with chemicals... If everything ok then check the switch connector for rust.... if it is clean then change the wires of pressure switch with connector ...
Finally possibilities of PCB faulty but rarely..
Hopefully instructions will help you..
What if it doesn't work even if i already replaced it with the new one?
1.Check the thin tube which connected between the tub and switch.
2. Remove the tube and clean it.
3. Remove the tube from switch side and fill the water half tub and check the clear water flow... Must be clear flow.
4. If no flow put some cleaninh chemicals to the tub vent while empty and leave it for 30 minutes.
Again fill the water check for clear flow.
*If everything works then possibly problems in circuit board which gives a pressure sensing signal.. Check the related components.
White line canakting
Please help me my washing machine is being overflow and no spinning
Remove back cover first. Then fill the half tub and remove the tub side thin pipe from the bottom side and check for proper water flow... If water flows clearly from the tub it means there is no any blockages in tub air pressure vent. Remove the thin pipe and clean with water if any blockages if everything ok then change the sensor switch...
Blockages or faulty sensor switch is the reasons for over flowing...
How much it cost that pressure switch
Rs 500 to 650....
@@noorie02 thnk u
What is the cost of this ..??
Rs 500- 600
Rate p E Erorr gadda price kiya hai
Water level gadda pricekiya hai
500-600
presure switch rate
Its around Rs. 450/-
Bai new switch lgga kr be PE aa rha hai
Remove back cover first. Then fill the half tub and remove the tub side thin pipe from the bottom side and check for proper water flow... If water flows clearly from the tub it means there is no any blockages in tub air pressure vent. Remove the thin pipe and clean with water if any blockages. Check wire connections of the switch...clean the Connectors if there any rust.. Change the wires kf damaged
What is the cost of new pressure switch ?
Its around Rs. 500/ to 600/
Hello, where it can be possible to buy that switch for LG washing machine?
Try any service center it is easily available.. . If not available try online shop
Take the sample is better....