Beginner Guide // How To Build Budget DJI Cinematic FPV Drone 2020
Vložit
- čas přidán 7. 08. 2024
- Part 2: • DJI FPV Drone Build //...
Drone Parts:
Racerstar Motors: bit.ly/2KIWZBE
FrSky R9 Mini: bit.ly/2m5gqfi
Geprc Mark4 HD: bit.ly/2UrramX
DJi Air Unit: bit.ly/31xC7qp
Batteries: bit.ly/2Piyqk8
Batteries #2: bit.ly/2AQY2vt
Propellers: bit.ly/2UdGxyM
Upgraded Flight Controller Combo: bit.ly/2WJUvu6
The Connection Are still the Same with the Upgraded Variant
Tools:
Hex Driver: bit.ly/2NwBVxt
Soldering Station: bit.ly/2ylZC9O
-- My Tools & Gear 2020--
Goggles #1: bit.ly/2YEjBwT
Google #2: bit.ly/2YDi4q8
RC Controller: bit.ly/2LR9uxc
Main Battery Charger: bit.ly/2SQGWp9
Fav Soldering Iron: bit.ly/2ylZC9O
-FPV Merch-
shopdronemesh.com/product-cat...
You need help getting Manufacturing and Product in Market:
dronemeshlabs@gmail.com
Want A Custom Build Email me:
dronemeshlabs@gmail.com
Follow Me on Instagram
/ dronemesh
Follow me on Facebook
/ dronemesh
Consider Following me and supporting on Patreon.
/ dronemesh
-Latest Fav Products-
FC #1: bit.ly/2Vz2Gro
Budget ESC: bit.ly/3elmaIu
-- My Tools & Gear 2020--
Goggles #1: bit.ly/2YEjBwT
Google #2: bit.ly/2YDi4q8
RC Controller: bit.ly/2LR9uxc
Main Battery Charger: bit.ly/2SQGWp9
Fav Soldering Iron: bit.ly/2ylZC9O
--Recording 2020--
Audio Interface: amzn.to/36iajaE
Microphones: amzn.to/3g9dyFR
Lav Microphone: amzn.to/3cNDZi1
Camera: amzn.to/2AEk3Qu
2nd Camera: amzn.to/2Tl1YNN
--PC Specs 2020--
AMD 3950x: amzn.to/2WRqEQx
GTX 2060: amzn.to/2XfEOtC
Auros Elite MB: amzn.to/3bNCQ91
Case: amzn.to/2LGMlwb
RGB Ram: amzn.to/2TmVm1G
Water Cooler: amzn.to/2zgeabR
-- TOP 30x30 4in1 ESC --
Aikon AK32
BG: bit.ly/2uSBI0O
GetFPV: bit.ly/2FU854b
RDQ: bit.ly/2YVkL3K
Tekko32 Metal
BG: bit.ly/2G5VfRC
GetFPV: bit.ly/2VsroYV
RDQ: bit.ly/2UF3WKU
T-Motor F55A
BG: bit.ly/2JIdAo1
GetFPV: bit.ly/2P2i8sp
RDQ: bit.ly/2I3D69n
T-Motor F45A
BG: bit.ly/2CZe9IP
GetFPV: bit.ly/2D3g2U3
RDQ: bit.ly/2YZmCof
Dalrc Rocket
BG: bit.ly/2O5Pcxc
GetFPV: bit.ly/2WQ8Imk
RDQ: bit.ly/2Kg0EKe
-- Best 20x20 4in1 ESC In Order From Best --
HGLRC Forward
BG: bit.ly/2CM2oEG
GETFPV: N/A
RDQ: bit.ly/2GfMKDQ
Aikon AK32 Mini
BG: bit.ly/2Yu2E4p
GetFPV: bit.ly/2KlKlLU
RDQ: bit.ly/2KfQ6KV
Airbot Ori32
BG: bit.ly/2UTK2JF
GETFPV: bit.ly/2KlLfrM
RDQ: bit.ly/2U94tRe
------------------------------------
I highly recommend these products if unsure
Tekko32
bit.ly/2NwffxB
kakuteV2 AIO
bit.ly/2CxQct0
Hakcrc (Best Budget ESC)
bit.ly/2OgrOlO
25km Range on these awesome VTX's
FX2
goo.gl/8PswEP
X2
goo.gl/VsDZ6n
---------------------------------------------------------------
The HEX driver I recommended which i bought 2 sets of (Must have if your into building)
bit.ly/2NwBVxt
Batteries I use
bit.ly/2PlCvQn
Camera I use
amzn.to/2iQHCwV
Standoffs I find to be the best
bit.ly/2CwG17Z
Xt60 Premade I use
bit.ly/2Pmf89j
Heat shrink I mentioned
bit.ly/2PkrVcA
Soldering station
bit.ly/2zZP9za
Some of the links are affiliated links.
Contact: mesh.drone@gmail.com - Věda a technologie
Drone Parts:
Racerstar Motors: bit.ly/2KIWZBE
FrSky R9 Mini: bit.ly/2m5gqfi
Geprc Mark4 HD: bit.ly/2UrramX
DJi Air Unit: bit.ly/31xC7qp
Batteries: bit.ly/2Piyqk8
Batteries #2: bit.ly/2AQY2vt
Propellers: bit.ly/2UdGxyM
Upgraded Flight Controller Combo: bit.ly/2WJUvu6
The Connection Are still the Same with the Upgraded Variant
Tools:
Hex Driver: bit.ly/2NwBVxt
Soldering Station: bit.ly/2ylZC9O
If I was to upgrade on the Fc and esc, what would be a good choice (with Dji pnp) ?
Also I have some Xing-e 2207 - 2450kv. Good fit?
do you have to use DJI goggles and controller with the DJI Air Unit????
@@JifferRiffic You have to use the goggles. You can add any reciever you like and use any controller supporting that reciever. But the air unit also support the dji controller. Then you don’t need any extra reciever. In short air unit is both vtx and reciever in one.
can you gift me plz 😍😍
Could you make a video on how to connect a controller?
Hey please do everything on screen everything if we’re watching were interested thanks you keep up the good work. EVERYTHING lol thanks
Beautiful build, Sam! 😃
Looking forward to the flight video!
Stay safe there with your family! 🖖😊
If you would use a dampened sponge to clean the soldering tip after a few connections you'll get better connections without globs of solder. Also, use a liquid flux pen or soldering rosin paste on the circuit board pads and the solder will flow much, much easier without you having to use so much solder.
Thanks for doing this please never give up
Just on time , thanks 🙏
Thanks for the drone content! +subscribed
Nice man !!
The quality of this video is just absolutely lit
This what I saw looking for !
I did this build, but with Xing E-2208 1700KV. great FC, shame no Inav target. All the 5v pads I used are powered by the USB, which is nice.
THANKS FOR THIS VIDEO AWESOME 💥💥💪
I like the racerstars man.
Old school!
unfortunately, we cannot use "DJI" and "budget" in the same sentence...lol
hm, I think you're not quite right. There is a proverb in Russia that greedy person pays twice. For example you decided to build first quad with analog video. Things you shuold by for video: VTX, 3 antenas, goggles(for example ev800d). Than you meet person with normal goggles and whant to buy them and the only thing wich is worth to be bought for upgrade is HDO2+rapidfire... For such a money it's better to by digital fpv system with awsome video quality and signal penetration than shitty analog. I was a little bit lucky to by for my first goggles aomway commander v1s for 120$. But as i watched HDO's quality with rapidfire i found out that there are not too much difference in video quality. So for now I'm hoarding money to buy DJI FPV system...I'm realy dreaming of it... But it cost as 4 my salarys... So I hope to hoard this some in a year... Or not to eat for 5 month))))
Yes..truueee af
@@user-lu2cy9xv2z this comment is 10 months old now. Did you get it?
@@x1c3x fuck yeah!!! but I had to sell my mini lathe and 1070ti...
@@user-lu2cy9xv2z Dreams really do come true
I havent used a mark 4 yet but i absolutely love the look of them.
thank yoooooooo perfect motors✊🏾✊🏾
Keep it up bro
Continu this👏👏
Ayyyy I’m building my next quad with the hifionrc f722 but they sent me the V2 version which doesn’t have the dual gyros but still super good for the price IMO
Amazing👏👏👏😍
Yeeeees I like it!
Drone Mesh I have been told that having the compassitor mounted on the battery plug the way you have it does little to stop power spikes, etc. Can you do a test to show how it helps mounted to the plug compared to mounting it on the ESC?? That's a nice quick easy build.
Question: can I use RX3/TX3 for DJI AIR UNIT for better cable management for example?
I have the same frame and I think the 20cm replacement cable for air unit is mandatory, else the cable introduces vibrations
Agree I love those motors 😊😊 what’s your oppinion on Hard mounting fc? Fettec highly recommends for their fc.based on that I decided to get Glider hammer from Fpv Cycle and put esc between arms on 30x30 and FC above middle plate on 20x20 mounting :) (+ emi and fire isolation 🤷♂️)
Yeah nice 😉
Do a top of the line DJI build as well!
I am new to Drone building. Very helpful video. Is there a specific reason why you did not use a PDB in this build?
A zip tie and a piece of heat shrink or tubing can make a cable stand off. Slide a piece of tube 1/8” long or so on to zip tie, loop the tie back into the heat shrink, opposite direction as first. Kind of looks like an eight, attach where ever. 🤙
Do you have a video about setup? You go from build to flying but there are way more steps binding ect.
Solder wick will remove unwanted solder.
Liquid or paste Flux would be helpful as well.
LMAO @ and "that's what she said", you caught me off guard. I watched many of your vids today as I want to build a long range quad. maybe a 5 inch with lower KV motors and a light weight deadcat style frame. I have the r9m 2019 with the super 8 antenna and the R9 MX OTA ACCESS Long Range Receiver with Ipex4 T Antenna. Thanks for all videos as I have never used the r9m, set it up or built my own quad. Your videos give me the confidence to carry on and...gitt'er done.
Is it possible to receive a digital HD video on a screen without having to buy dji goggles? Like a module that outputs the video feed to hdmi or usb C to connect with your phone, pc or any other screen.
Hi, Do you have any video that showing how to build a drone that navigate by laser, for example, I target some point at the ground and the drone should land there? Thank you for eventually replay 😀
Awesome build sir !
Is it possible to do the same build but with a Caddx Vista and a TBS Nano Rx ?
Someone please help, I'm just starting fpv, I got my first protek35 prebuilt with dji digital setup and now I am looking to build or buy another different drone, what receiver do I need to look for to be on the drone for it to work with the dji controller, struggling to find a video on this? Is it the Fr sky one?
Noob question here. It looks like the solder points on each pad of the ESC are slightly touching each other. Doesn't this impact the signals?
How fast can this go and what type of range can you get with this using the Dji fpv controller and goggles v1
I also want to know why have used air unit instead of vista? Also for real I think that iflight 5 inch frames are much better and have more smart solutions for example motorwires protection, reciever holder and etc...
why do you rub the solder tip on the contact as compared to just placing it on the area when soldering?
Where do we get the 3D printed parts for the motor guards, the mount for the FrSky R9 Mini, etc.
I found this o helpful for my 1st build and i am stuck now with the motors saying cc and ccw which order should i place it and also a 3d printed tpu for holding dji air unit can you please help out me sir?
So if I were to buy the Air unit with the controller, i would be able to skip adding that additional receiver?
Can you make a video on your main basher style quad? Please 🙏
Can you use radiomaster radio with this or do you need a dji radio?
what did you solder the capacitor and the battery cables too its hard to see it in the video??????
Nice 👌👌👌👍👍👌👍
Hey Sam, when can we seen a part two for this video about performance, flight times (and ways to get the most out with varying batteries), distance and with go pro on vs go pro lite on
I was looking for the exact same thing.
The DJI Air unit alone is US$179.00 so how you calculated 161$?
These motors are bad. The bearings are the worst I ever had and the magnets become loose on 5-6s resulting in random crashes.
Better take some cheap from T-Motor !
Greetings
I was thinking the same thing! Freaking click bait video. SMH
Or even the iflight xing e line. Thosr are pretty dang good for a budget motor
Do you have an updated version of this for 2022 / 2023???
Great
Thanks very helpful but can you do a follow up video for total beginners that shows parts that you skipped, like extending the DJI cable (where did you get the extra cable?), attaching the xt60, attaching the capacitor to the xt60 (you said we would have been bored but i dont know why. If it really takes a long time, maybe do a timelapse or add voiceover to explain stuff), attaching the ESC to the frame, connecting the ESC to the FC, installing the motors on the frame, changing the motor spin orientation, setting up in betaflight. Also I thought i saw r3 and t3 toward the rear. Is there a reason you didnt use those instead for the DJI cable? Anyway this video did really well and i think this follow up would also do well.
you need a capacitor for xt60 to lower the noise aka voltage spikes which might cause interference with your quad's video and control or even damage your esc
hi there what is the link for the smaller capacitor as can't see it? thanks
Can you link the Battery cable holder you mentioned?
Can you please share the stl's you used for this build. Thanks
Your Thumbnail is miss leading!! The DJI Air Unit alone is more the $161.00. I call click bait in this video!
Yep, click bait like this gets a thumbs down even though I enjoyed the video. Can't support this kind of blatant click bait.
Thank you for the step-by-step walkthrough video! Just started getting into FPV drone building but I had a question about the build. Is there a specific capacitor that we need to connect to the XT60? I saw in the video that you used a 830uf 25V panasonic capacitor but I was only able to find 820uf 25V capacitors. Will that make a difference? Thanks again!
i had the same question, did you find the answer?
Do you have a more detailed video for installing the low noise stuff and the camera? I’ve never built one before and want to. But your video assumes a little experience building. Lol. Have anything like this for absolute beginners?
I have a Phantom3 Pro and I want to use the parts to build something else. Has anyone done or seen a video about it? If so please share link
So where are the Stls for the 3D printed parts? I want the XT60 holder..
So if you had the dji remote you wouldn’t need to add a receiver?
THATS AWSOME!
"Thats what she said!🤣"
Could you do a video on how exactly you chose components and check for compatibility for a given build? That would be huge! Thanks
I have done videos like that however I can revisit. How are you searching for this topic so I can position the videos tittle correctly.
Is there any coding we have to do after finishing?
Although i dont have money 💰 to buy dji goggles because they are so freakin expensive but i love to watch your videos may be some day
What's the final weight on something like this? Do they fall under 250g? I want to look at alternatives to the DJI mini 3 pro
No this don't fall under 250g.
in part two, can you please experiment with the battery setup to maximise flight time and also test range (mid range cinematic fpv with DJI unit at 20min+ flight time would be duh dream)
with of course go pro mounted, hero 7
How do you know all the electronics work together?
How do we get an INAV target for this great FC?
Where can i see how they fly and the camera quality?
Where did you find the 3D printed motor guards?
does it have alt hold or return ?
Does the drone have live feed to a phone? Or pc?
Is the battery rechargable
Can you control this with a smartphone?
Hi, where can I get this XT60 3d printed part?
when you soldered the motors onto the board because there's 3 wires do they have to be in a specific config, or does it not matter as long as you solder them to their corresponding sections?
Depending on the board, it may not matter. The esc he’s using, you can change the motor rotation in the software.
It looks like the R9 mini uses ACCESS protocol. Do we need a FrSky Radio for this to work ? or can we use Jumper/Radiomaster ?
I am new to fpv. I bought the Frsky radio and the receiver but I couldn't bind it to my radio through ACCESS protocol. And just after that I tried flashing Different firmware LBT or FCC. It still didnt work. Then I looked at the manual and online and it turns out these R9 mini OTA receivers are compatible with external module called R9M or R9M lite... cuz those are long range receivers up to 10km so needs external modules. I am learning myself just looking thro different yt videos or googling for answer😄😄
Maybe I’m putting to much faith in you but... you seem to think out and test everything before you speak, most the time haha. I trust what you say. Thanks for the video.
Is there going to be a part 2 to this? Please respond
A demo would have made this an excellent video.
Will this have geofencing?
Will dji rc work with this drone???
What solder do you use???
sir,also make a 200usd drones fpv racing ones and thannks for this video
Agree with this. Would be nice to see a racing build.
Drone mesh i have an idea that i kinda want to bring life and would like to know were i could get a PCD or PDB printed
Pcbway is where I get everything done
Can you put the link to every single component
Do sell the frame "foldable" ?
So once I’m putting this together... what else is there to do? Is it ready to flight once built?
You need to set it up
Does race wire/PCBs diminish energy sent to the motor at all?
Oh, and can I use this frame with the Caddx Vista instead? I have an extra one laying around
Hey man I want to get into this sport - what are good goggles and cheep ones and also what are good and cheap controller that I need which would fit the receiver etc.... please help haha
Best budget google is eachine ev800d (analog) and radio Radiomaster tx16s Hall
@@janickithomas thanks buddy and do they support all the recivers and stuff on the drone ? or i need special reciver for the remote and goggles?
will this frame allow to use an analog VTX instead of DJI air unit?
Greetings from Colombia
There is the non HD version
What happened to drone mesh? ?????
would this build work for an analogue vtx? If so, what vtx and camera would you recommend?
Rushfpv vtx and a forever or runcam
@@DroneMesh Hi sorry I'm super new in the fpv scene. I found the vtx but could you elaborate a bit more on the camera?
Naissss
So...mow much does this budget build in fact cost?
Why FPV drone have Ba glitchy camera
The hex link doesn't work...
Is it same for 6s build too ..??
do not take those motors on 6s! The bearings are the worst I ever had and the magnets become loose on 5S and 6s resulting in random crashes.
Hey there i am new I am now learning I went to my local Air field and watched some guys fly after i was flying i dropped everything watched them fly omg i was hooked i was wondering if u could get me set up right and help me build my own because I love building plans and cars so I ready to learn if u could get me set i want vr for start I want it fast okay really fast is possible for some that is learning about this now